Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

STM32U575CIT6Q

STMICROELECTRONICS · Global Sourcing Parts · LQFP-48(7x7)

STM32U575CIT6Q from STMICROELECTRONICS, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VBAT power_in Backup-domain supply pin that powers the RTC, the 32 x 32-bit backup registers and the 2-Kbyte backup SRAM in VBAT mode.
2 PC13 bidirectional FT_o I/O supplied through the power switch (VSW) with EVENTOUT, WKUP2, RTC_TS/RTC_OUT1 and TAMP_IN1/TAMP_OUT2 functions; the switch sinks only 3 mA, so output speed must not exceed 2 MHz at 30 pF and the pin must not be used as a current source.
3 PC14-OSC32_IN bidirectional FT_o I/O supplied through the power switch (VSW) that doubles as the OSC32_IN low-speed oscillator input, with the same 3 mA shared source limit as PC13 to PC15.
4 PC15-OSC32_OUT bidirectional FT_o I/O supplied through the power switch (VSW) that doubles as the OSC32_OUT low-speed oscillator output, with the same 3 mA shared source limit as PC13 to PC15.
5 PH0-OSC_IN (PH0) bidirectional FT I/O whose additional function is the OSC_IN high-speed oscillator input.
6 PH1-OSC_OUT (PH1) bidirectional FT I/O whose additional function is the OSC_OUT high-speed oscillator output.
7 NRST bidirectional Bidirectional reset pin with an embedded weak pull-up resistor.
8 VSSA power_in Analog ground for the ADCs, DACs, OPAMPs, COMPs and VREFBUF.
9 VDDA power_in Analog supply for the ADCs, DACs, OPAMPs, COMPs and VREFBUF, to be decoupled to VSSA.
10 PA0 bidirectional FT_ha I/O with analog switch function supplied by VDDA, also ADC1_IN5, OPAMP1_VINP, WKUP1 and TAMP_IN2/TAMP_OUT1, with alternate functions TIM2_CH1, TIM5_CH1, USART2_CTS and UART4_TX.
11 PA1 bidirectional FT_hat I/O with analog switch function supplied by VDDA, also ADC1_IN6, OPAMP1_VINM, WKUP3 and TAMP_IN5/TAMP_OUT4, with alternate functions TIM2_CH2, TIM5_CH2, SPI1_SCK, USART2_RTS/USART2_DE and UART4_RX.
12 PA2 bidirectional FT_ha I/O with analog switch function supplied by VDDA, also COMP1_INP3, ADC1_IN7 and WKUP4/LSCO, with alternate functions TIM2_CH3, TIM5_CH3, USART2_TX (boot), LPUART1_TX and UCPD1_FRSTX1.
13 PA3 bidirectional TT_hav I/O (3.6 V tolerant) with analog switch function supplied by VDDA, also OPAMP1_VOUT, ADC1_IN8 and WKUP5, with alternate functions TIM2_CH4, TIM5_CH4, SAI1_CK1, USART2_RX (boot) and LPUART1_RX.
14 PA4 bidirectional TT_ha I/O (3.6 V tolerant) with analog switch function supplied by VDDA, also ADC1_IN9, ADC4_IN9, DAC1_OUT1 and WKUP2, with alternate functions SPI1_NSS (boot), SPI3_NSS, USART2_CK and DCMI_HSYNC/PSSI_DE.
15 PA5 bidirectional TT_a I/O (3.6 V tolerant) with analog switch function supplied by VDDA, also ADC1_IN10, ADC4_IN10, DAC1_OUT2 and WKUP6, with alternate functions TIM2_CH1, TIM2_ETR, SPI1_SCK (boot), USART3_RX and LPTIM2_ETR.
16 PA6 bidirectional FT_ha I/O with analog switch function supplied by VDDA, also OPAMP2_VINP, ADC1_IN11, ADC4_IN11 and WKUP7, with alternate functions TIM1_BKIN, TIM3_CH1, TIM8_BKIN, SPI1_MISO (boot), USART3_CTS and LPUART1_CTS.
17 PA7 bidirectional FT_fha I/O with analog switch function supplied by VDDA and Fm+ capability, also OPAMP2_VINM, ADC1_IN12, ADC4_IN20 and WKUP8, with alternate functions TIM1_CH1N, TIM3_CH2, TIM8_CH1N, I2C3_SCL, SPI1_MOSI (boot) and USART3_TX.
18 PB0 bidirectional TT_ha I/O (3.6 V tolerant) with analog switch function supplied by VDDA, also OPAMP2_VOUT, ADC1_IN15 and ADC4_IN18, with alternate functions TIM1_CH2N, TIM3_CH3, TIM8_CH2N, SPI1_NSS, USART3_CK and COMP1_OUT.
19 PB1 bidirectional FT_ha I/O with analog switch function supplied by VDDA, also COMP1_INM1, ADC1_IN16, ADC4_IN19 and WKUP4, with alternate functions TIM1_CH3N, TIM3_CH4, LPTIM3_CH2, MDF1_SDI0, USART3_RTS/USART3_DE and LPUART1_RTS/LPUART1_DE.
20 VLXSMPS power_out SMPS switching node that must be connected to a 2.2 µH ±20% inductor (ISAT > 0.5 A, DCR < 200 mΩ) between VLXSMPS and VDD11.
21 VDDSMPS power_in Supply input of the SMPS step-down converter, which requires a 10 µF ±20% input capacitor with ESR < 10 mΩ at 3 MHz and a rated voltage of at least 10 V.
22 VSSSMPS power_in Ground return pin of the SMPS step-down converter.
23 VDD11 power_out SMPS-regulated core supply node that requires 2 × 2.2 µF ±20% output capacitors with ESR < 20 mΩ at 3 MHz and a rated voltage of at least 10 V.
24 VSS power_in Ground pin, which must always be connected to the ground of the external supply.
25 VDD power_in Main power supply pin operating from 1.71 V to 3.6 V.
26 PB13 bidirectional FT_fa I/O with Fm+ capability, with alternate functions TIM1_CH1N, LPTIM3_IN1, I2C2_SCL, SPI2_SCK (boot), MDF1_CKI1, USART3_CTS, LPUART1_CTS and SAI2_SCK_A.
27 PB14 bidirectional FT_fda I/O with Fm+ capability and UCPD dead-battery function, with alternate functions TIM1_CH2N, LPTIM3_ETR, TIM8_CH2N, I2C2_SDA, SPI2_MISO (boot), MDF1_SDI2 and USART3_RTS/USART3_DE; its internal pull-down enables the PA15 (UCPD1_CC1) dead-battery pull-down when high.
28 PB15 bidirectional FT_c I/O (5.5 V maximum input voltage) with USB Type-C function UCPD1_CC2 and WKUP7, with alternate functions RTC_REFIN, TIM1_CH3N, LPTIM2_IN2, TIM8_CH3N, SPI2_MOSI (boot) and SDMMC2_D1.
29 PA8 bidirectional FT_hv I/O (very high-speed capable), with alternate functions MCO, TIM1_CH1, SAI1_CK2, SPI1_RDY, USART1_CK, OTG_FS_SOF and TRACECLK.
30 PA9 bidirectional FT_u I/O whose USB function is supplied by VDDUSB, also OTG_FS_VBUS, with alternate functions TIM1_CH2, SPI2_SCK, DCMI_D0/PSSI_D0, USART1_TX (boot) and SAI1_FS_A.
31 PA10 bidirectional FT_u I/O whose USB function is supplied by VDDUSB, also OTG_FS_ID, with alternate functions CRS_SYNC, TIM1_CH3, LPTIM2_IN2, SAI1_D1, DCMI_D1/PSSI_D1 and USART1_RX (boot).
32 PA11 bidirectional FT_u I/O whose USB function is supplied by VDDUSB, also OTG_FS_DM (boot), with alternate functions TIM1_CH4, TIM1_BKIN2, SPI1_MISO, USART1_CTS, FDCAN1_RX and EVENTOUT.
33 PA12 bidirectional FT_u I/O whose USB function is supplied by VDDUSB, also OTG_FS_DP (boot), with alternate functions TIM1_ETR, SPI1_MOSI, OCTOSPIM_P2_NCS, USART1_RTS/USART1_DE and FDCAN1_TX.
34 PA13 bidirectional FT I/O that after reset is configured as the JTMS/SWDIO debug function with an internal pull-up enabled, with alternate functions IR_OUT, OTG_FS_NOE and SAI1_SD_B.
35 VSS power_in Ground pin, which must always be connected to the ground of the external supply.
36 VDD power_in Main power supply pin operating from 1.71 V to 3.6 V.
37 PA14 bidirectional FT I/O that after reset is configured as the JTCK/SWCLK debug function with an internal pull-down enabled, with alternate functions LPTIM1_CH1, I2C1_SMBA, I2C4_SMBA, OTG_FS_SOF and SAI1_FS_B.
38 PA15 (JTDI) bidirectional FT_c I/O (5.5 V maximum input voltage) that after reset is configured as JTDI with an internal pull-up, also UCPD1_CC1 dead-battery pull-down, with alternate functions TIM2_CH1, TIM2_ETR, USART2_RX, SPI1_NSS, SPI3_NSS and SAI2_FS_B.
39 PB3 bidirectional FT_fa I/O that after reset is configured as JTDO/TRACESWO, also COMP2_INM2, with alternate functions TIM2_CH2, LPTIM1_CH1, I2C1_SDA, SPI1_SCK, SPI3_SCK and USART1_RTS/USART1_DE.
40 PB4 (NJTRST) bidirectional FT_fa I/O that after reset is configured as NJTRST with an internal pull-up enabled, also COMP2_INP1, with alternate functions LPTIM1_CH2, TIM3_CH1, SPI1_MISO, SPI3_MISO and USART1_CTS.
41 PB5 bidirectional FT_havd I/O with USB Type-C dead-battery function UCPD1_DBCC1 and WKUP6, with alternate functions LPTIM1_IN1, TIM3_CH2, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI (boot) and USART1_CK.
42 PB6 bidirectional FT_fa I/O with Fm+ capability, also COMP2_INP2 and WKUP3, with alternate functions LPTIM1_ETR, TIM4_CH1, I2C1_SCL (boot), I2C4_SCL and USART1_TX.
43 PB7 bidirectional FT_fhav I/O with Fm+ capability, also COMP2_INM1, PVD_IN and WKUP4, with alternate functions LPTIM1_IN2, TIM4_CH2, I2C1_SDA (boot), I2C4_SDA and USART1_RX.
44 PH3-BOOT0 bidirectional FT I/O that also provides the BOOT0 boot-selection function, and BOOT0 is excluded from the standard I/O input characteristics.
45 PB8 bidirectional FT_f I/O with Fm+ capability and WKUP5, with alternate functions TIM4_CH3, SAI1_CK1, I2C1_SCL, MDF1_CCK0, FDCAN1_RX (boot), SDMMC2_D4 and TIM16_CH1.
46 VDD11 power_out SMPS-regulated core supply node that requires 2 × 2.2 µF ±20% output capacitors with ESR < 20 mΩ at 3 MHz and a rated voltage of at least 10 V.
47 VSS power_in Ground pin, which must always be connected to the ground of the external supply.
48 VDD power_in Main power supply pin operating from 1.71 V to 3.6 V.

Key specifications

Parameter Value
Manufacturer STMICROELECTRONICS
Package LQFP-48(7x7)
Category Global Sourcing Parts
Pins 48

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Standard operating voltage (IO_VDD_HSLV = 0) VDD 1.71 3.6 V IO_VDD_HSLV = 0 156
Standard operating voltage (IO_VDD_HSLV = 1) VDD 1.71 2.7 V IO_VDD_HSLV = 1 156
Supply voltage for PG[15:2] I/Os VDDIO2 1.08 3.6 V At least one I/O in PG[15:2] used, IO_VDDIO2_HSLV = 0 156
Supply voltage for PG[15:2] I/Os (HSLV) VDDIO2 1.08 2.7 V At least one I/O in PG[15:2] used, IO_VDDIO2_HSLV = 1 156
Supply voltage for PG[15:2] I/Os (not used) VDDIO2 0 3.6 V PG[15:2] I/Os not used 156
USB supply voltage VDDUSB 3 3.6 V USB used 156
USB supply voltage (not used) VDDUSB 0 3.6 V USB not used 156
Analog supply voltage VDDA 1.58 3.6 V COMP used 156
Analog supply voltage VDDA 1.6 3.6 V DAC or OPAMP used 156
Analog supply voltage VDDA 1.62 3.6 V ADC used 156
Analog supply voltage VDDA 1.8 3.6 V VREFBUF used (normal mode) 156
Analog supply voltage (not used) VDDA 0 3.6 V ADC, DAC, COMP, OPAMP, and VREFBUF not used 156
Backup domain supply voltage VBAT 1.65 3.6 V 156
I/O input voltage VIN -0.3 V All I/Os except FT_c and TT_xx pins; max is a formula, see review_required 156
Input voltage on FT_t pins in VBAT mode VIN -0.3 V FT_t pins in VBAT mode; max is a formula, see review_required 156
FT_c I/O input voltage VIN -0.3 5 V FT_c I/Os 156
TT_xx I/O input voltage VIN -0.3 V TT_xx I/Os; max is VDDIOx + 0.3, see review_required 156
Sum of output current sourced by all I/Os powered by VSW IIO_SW 3 mA 156
Internal regulator VCORE VCORE 1.15 1.21 1.27 V Internal regulator ON, Range 1 157
Internal regulator VCORE VCORE 1.05 1.1 1.15 V Internal regulator ON, Range 2 157
Internal regulator VCORE VCORE 0.95 1 1.05 V Internal regulator ON, Range 3 157
Internal regulator VCORE VCORE 0.81 0.9 0.99 V Internal regulator ON, Range 4 157
AHB clock frequency fHCLK fHCLK 160 MHz Voltage scaling Range 1 157
AHB clock frequency fHCLK fHCLK 110 MHz Voltage scaling Range 2 157
AHB clock frequency fHCLK fHCLK 55 MHz Voltage scaling Range 3 157
AHB clock frequency fHCLK fHCLK 25 MHz Voltage scaling Range 4 157
Ambient temperature for suffix 6 (maximum power dissipation) TA -40 85 °C Suffix 6, maximum power dissipation 158
Ambient temperature for suffix 6 (low-power dissipation) TA -40 105 °C Suffix 6, low-power dissipation 158
Junction temperature range TJ -40 105 °C Suffix 6 version 158
Voltage on VDDX - VSS (external main supply) VDDX - VSS -0.3 4 V Includes VDDSMPS, VDDA, VDDUSB, VBAT, VREF+ 154
I/O supply VDDIOx - VSS VDDIOx - VSS -0.3 4 V I/O supply when HSLV = 0 154
I/O supply VDDIOx - VSS VDDIOx - VSS -0.3 2.75 V I/O supply when HSLV = 1 154
Input voltage on FT_xx pins except FT_c pins VIN -0.3 V Max is a formula, see review_required 154
Input voltage on FT_c pins VIN -0.3 5.5 V 154
Input voltage on any other pins VIN -0.3 4 V 154
Allowed voltage difference for VREF+ > VDDA VREF+ - VDDA 0.4 V VREF+ > VDDA; printed as '- 0.4', read as max, see review_required 154
Variations between different VDDx power pins of the same domain /ΔVDDx/ 50 mV 154
Variations between all the different ground pins /VSSx-VSS/ 50 mV Including VREF- pin 154
Total current into sum of all VDD power lines (source) ∑IVDD 200 mA 154
Total current out of sum of all VSS ground lines (sink) ∑IVSS 200 mA 154
Maximum current into each VDD power pin (source) IVDD 100 mA 154
Maximum current out of each VSS ground pin (sink) IVSS 100 mA 154
Output current sunk by any I/O and control pin IIO 20 mA Sink 154
Output current sourced by any I/O and control pin IIO 20 mA Source 154
Total output current sunk by sum of all I/Os and control pins ∑I(PIN) 120 mA Sink 154
Total output current sourced by sum of all I/Os and control pins ∑I(PIN) 120 mA Source 154
Injected current on FT_xx, TT_xx, RST pins IINJ(PIN) -5 0 mA 154
Total injected current (sum of all I/Os and control pins) ∑/IINJ(PIN)/ 25 mA Printed as ±25; absolute sum of injected currents 154
Storage temperature range TSTG -65 150 °C 155
Maximum junction temperature TJ 140 °C 155
Embedded brownout reset threshold 0 (rising edge) VBOR0 1.6 1.66 1.71 V Rising edge 159
Embedded brownout reset threshold 0 (falling edge) VBOR0 1.58 1.64 1.69 V Falling edge, range 1, 2, 3 159
VBAT brownout reset threshold VBOR_VBAT 1.58 1.65 V 160
Internal reference voltage VREFINT 1.175 1.215 1.255 V Range 1, 2, 3 161

CAD (KiCad official)

  • Symbol: STM32U575CIT6Q
  • Footprint: Package_QFP:LQFP-48_7x7mm_P0.5mm
  • 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
  • 3D model files: stm32u575cit6q-etched.step / stm32u575cit6q-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm32u575cit6q.step / stm32u575cit6q.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMICROELECTRONICS datasheet (346 pp, sha256 f3de0b5e62ad45ed, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF