component
STM32U575CIT6Q
Public Made by Adomby adom
STMICROELECTRONICS Global Sourcing Parts, LQFP-48(7x7). Pinout checked against ST's open pin data, KiCad symbol/footprint/3D.
Generated by kicad-footprint-generator · KiCad file format 20260206
STM32U575CIT6Q
STMICROELECTRONICS · Global Sourcing Parts · LQFP-48(7x7)
STM32U575CIT6Q from STMICROELECTRONICS, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup-domain supply pin that powers the RTC, the 32 x 32-bit backup registers and the 2-Kbyte backup SRAM in VBAT mode. |
| 2 | PC13 | bidirectional | FT_o I/O supplied through the power switch (VSW) with EVENTOUT, WKUP2, RTC_TS/RTC_OUT1 and TAMP_IN1/TAMP_OUT2 functions; the switch sinks only 3 mA, so output speed must not exceed 2 MHz at 30 pF and the pin must not be used as a current source. |
| 3 | PC14-OSC32_IN | bidirectional | FT_o I/O supplied through the power switch (VSW) that doubles as the OSC32_IN low-speed oscillator input, with the same 3 mA shared source limit as PC13 to PC15. |
| 4 | PC15-OSC32_OUT | bidirectional | FT_o I/O supplied through the power switch (VSW) that doubles as the OSC32_OUT low-speed oscillator output, with the same 3 mA shared source limit as PC13 to PC15. |
| 5 | PH0-OSC_IN (PH0) | bidirectional | FT I/O whose additional function is the OSC_IN high-speed oscillator input. |
| 6 | PH1-OSC_OUT (PH1) | bidirectional | FT I/O whose additional function is the OSC_OUT high-speed oscillator output. |
| 7 | NRST | bidirectional | Bidirectional reset pin with an embedded weak pull-up resistor. |
| 8 | VSSA | power_in | Analog ground for the ADCs, DACs, OPAMPs, COMPs and VREFBUF. |
| 9 | VDDA | power_in | Analog supply for the ADCs, DACs, OPAMPs, COMPs and VREFBUF, to be decoupled to VSSA. |
| 10 | PA0 | bidirectional | FT_ha I/O with analog switch function supplied by VDDA, also ADC1_IN5, OPAMP1_VINP, WKUP1 and TAMP_IN2/TAMP_OUT1, with alternate functions TIM2_CH1, TIM5_CH1, USART2_CTS and UART4_TX. |
| 11 | PA1 | bidirectional | FT_hat I/O with analog switch function supplied by VDDA, also ADC1_IN6, OPAMP1_VINM, WKUP3 and TAMP_IN5/TAMP_OUT4, with alternate functions TIM2_CH2, TIM5_CH2, SPI1_SCK, USART2_RTS/USART2_DE and UART4_RX. |
| 12 | PA2 | bidirectional | FT_ha I/O with analog switch function supplied by VDDA, also COMP1_INP3, ADC1_IN7 and WKUP4/LSCO, with alternate functions TIM2_CH3, TIM5_CH3, USART2_TX (boot), LPUART1_TX and UCPD1_FRSTX1. |
| 13 | PA3 | bidirectional | TT_hav I/O (3.6 V tolerant) with analog switch function supplied by VDDA, also OPAMP1_VOUT, ADC1_IN8 and WKUP5, with alternate functions TIM2_CH4, TIM5_CH4, SAI1_CK1, USART2_RX (boot) and LPUART1_RX. |
| 14 | PA4 | bidirectional | TT_ha I/O (3.6 V tolerant) with analog switch function supplied by VDDA, also ADC1_IN9, ADC4_IN9, DAC1_OUT1 and WKUP2, with alternate functions SPI1_NSS (boot), SPI3_NSS, USART2_CK and DCMI_HSYNC/PSSI_DE. |
| 15 | PA5 | bidirectional | TT_a I/O (3.6 V tolerant) with analog switch function supplied by VDDA, also ADC1_IN10, ADC4_IN10, DAC1_OUT2 and WKUP6, with alternate functions TIM2_CH1, TIM2_ETR, SPI1_SCK (boot), USART3_RX and LPTIM2_ETR. |
| 16 | PA6 | bidirectional | FT_ha I/O with analog switch function supplied by VDDA, also OPAMP2_VINP, ADC1_IN11, ADC4_IN11 and WKUP7, with alternate functions TIM1_BKIN, TIM3_CH1, TIM8_BKIN, SPI1_MISO (boot), USART3_CTS and LPUART1_CTS. |
| 17 | PA7 | bidirectional | FT_fha I/O with analog switch function supplied by VDDA and Fm+ capability, also OPAMP2_VINM, ADC1_IN12, ADC4_IN20 and WKUP8, with alternate functions TIM1_CH1N, TIM3_CH2, TIM8_CH1N, I2C3_SCL, SPI1_MOSI (boot) and USART3_TX. |
| 18 | PB0 | bidirectional | TT_ha I/O (3.6 V tolerant) with analog switch function supplied by VDDA, also OPAMP2_VOUT, ADC1_IN15 and ADC4_IN18, with alternate functions TIM1_CH2N, TIM3_CH3, TIM8_CH2N, SPI1_NSS, USART3_CK and COMP1_OUT. |
| 19 | PB1 | bidirectional | FT_ha I/O with analog switch function supplied by VDDA, also COMP1_INM1, ADC1_IN16, ADC4_IN19 and WKUP4, with alternate functions TIM1_CH3N, TIM3_CH4, LPTIM3_CH2, MDF1_SDI0, USART3_RTS/USART3_DE and LPUART1_RTS/LPUART1_DE. |
| 20 | VLXSMPS | power_out | SMPS switching node that must be connected to a 2.2 µH ±20% inductor (ISAT > 0.5 A, DCR < 200 mΩ) between VLXSMPS and VDD11. |
| 21 | VDDSMPS | power_in | Supply input of the SMPS step-down converter, which requires a 10 µF ±20% input capacitor with ESR < 10 mΩ at 3 MHz and a rated voltage of at least 10 V. |
| 22 | VSSSMPS | power_in | Ground return pin of the SMPS step-down converter. |
| 23 | VDD11 | power_out | SMPS-regulated core supply node that requires 2 × 2.2 µF ±20% output capacitors with ESR < 20 mΩ at 3 MHz and a rated voltage of at least 10 V. |
| 24 | VSS | power_in | Ground pin, which must always be connected to the ground of the external supply. |
| 25 | VDD | power_in | Main power supply pin operating from 1.71 V to 3.6 V. |
| 26 | PB13 | bidirectional | FT_fa I/O with Fm+ capability, with alternate functions TIM1_CH1N, LPTIM3_IN1, I2C2_SCL, SPI2_SCK (boot), MDF1_CKI1, USART3_CTS, LPUART1_CTS and SAI2_SCK_A. |
| 27 | PB14 | bidirectional | FT_fda I/O with Fm+ capability and UCPD dead-battery function, with alternate functions TIM1_CH2N, LPTIM3_ETR, TIM8_CH2N, I2C2_SDA, SPI2_MISO (boot), MDF1_SDI2 and USART3_RTS/USART3_DE; its internal pull-down enables the PA15 (UCPD1_CC1) dead-battery pull-down when high. |
| 28 | PB15 | bidirectional | FT_c I/O (5.5 V maximum input voltage) with USB Type-C function UCPD1_CC2 and WKUP7, with alternate functions RTC_REFIN, TIM1_CH3N, LPTIM2_IN2, TIM8_CH3N, SPI2_MOSI (boot) and SDMMC2_D1. |
| 29 | PA8 | bidirectional | FT_hv I/O (very high-speed capable), with alternate functions MCO, TIM1_CH1, SAI1_CK2, SPI1_RDY, USART1_CK, OTG_FS_SOF and TRACECLK. |
| 30 | PA9 | bidirectional | FT_u I/O whose USB function is supplied by VDDUSB, also OTG_FS_VBUS, with alternate functions TIM1_CH2, SPI2_SCK, DCMI_D0/PSSI_D0, USART1_TX (boot) and SAI1_FS_A. |
| 31 | PA10 | bidirectional | FT_u I/O whose USB function is supplied by VDDUSB, also OTG_FS_ID, with alternate functions CRS_SYNC, TIM1_CH3, LPTIM2_IN2, SAI1_D1, DCMI_D1/PSSI_D1 and USART1_RX (boot). |
| 32 | PA11 | bidirectional | FT_u I/O whose USB function is supplied by VDDUSB, also OTG_FS_DM (boot), with alternate functions TIM1_CH4, TIM1_BKIN2, SPI1_MISO, USART1_CTS, FDCAN1_RX and EVENTOUT. |
| 33 | PA12 | bidirectional | FT_u I/O whose USB function is supplied by VDDUSB, also OTG_FS_DP (boot), with alternate functions TIM1_ETR, SPI1_MOSI, OCTOSPIM_P2_NCS, USART1_RTS/USART1_DE and FDCAN1_TX. |
| 34 | PA13 | bidirectional | FT I/O that after reset is configured as the JTMS/SWDIO debug function with an internal pull-up enabled, with alternate functions IR_OUT, OTG_FS_NOE and SAI1_SD_B. |
| 35 | VSS | power_in | Ground pin, which must always be connected to the ground of the external supply. |
| 36 | VDD | power_in | Main power supply pin operating from 1.71 V to 3.6 V. |
| 37 | PA14 | bidirectional | FT I/O that after reset is configured as the JTCK/SWCLK debug function with an internal pull-down enabled, with alternate functions LPTIM1_CH1, I2C1_SMBA, I2C4_SMBA, OTG_FS_SOF and SAI1_FS_B. |
| 38 | PA15 (JTDI) | bidirectional | FT_c I/O (5.5 V maximum input voltage) that after reset is configured as JTDI with an internal pull-up, also UCPD1_CC1 dead-battery pull-down, with alternate functions TIM2_CH1, TIM2_ETR, USART2_RX, SPI1_NSS, SPI3_NSS and SAI2_FS_B. |
| 39 | PB3 | bidirectional | FT_fa I/O that after reset is configured as JTDO/TRACESWO, also COMP2_INM2, with alternate functions TIM2_CH2, LPTIM1_CH1, I2C1_SDA, SPI1_SCK, SPI3_SCK and USART1_RTS/USART1_DE. |
| 40 | PB4 (NJTRST) | bidirectional | FT_fa I/O that after reset is configured as NJTRST with an internal pull-up enabled, also COMP2_INP1, with alternate functions LPTIM1_CH2, TIM3_CH1, SPI1_MISO, SPI3_MISO and USART1_CTS. |
| 41 | PB5 | bidirectional | FT_havd I/O with USB Type-C dead-battery function UCPD1_DBCC1 and WKUP6, with alternate functions LPTIM1_IN1, TIM3_CH2, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI (boot) and USART1_CK. |
| 42 | PB6 | bidirectional | FT_fa I/O with Fm+ capability, also COMP2_INP2 and WKUP3, with alternate functions LPTIM1_ETR, TIM4_CH1, I2C1_SCL (boot), I2C4_SCL and USART1_TX. |
| 43 | PB7 | bidirectional | FT_fhav I/O with Fm+ capability, also COMP2_INM1, PVD_IN and WKUP4, with alternate functions LPTIM1_IN2, TIM4_CH2, I2C1_SDA (boot), I2C4_SDA and USART1_RX. |
| 44 | PH3-BOOT0 | bidirectional | FT I/O that also provides the BOOT0 boot-selection function, and BOOT0 is excluded from the standard I/O input characteristics. |
| 45 | PB8 | bidirectional | FT_f I/O with Fm+ capability and WKUP5, with alternate functions TIM4_CH3, SAI1_CK1, I2C1_SCL, MDF1_CCK0, FDCAN1_RX (boot), SDMMC2_D4 and TIM16_CH1. |
| 46 | VDD11 | power_out | SMPS-regulated core supply node that requires 2 × 2.2 µF ±20% output capacitors with ESR < 20 mΩ at 3 MHz and a rated voltage of at least 10 V. |
| 47 | VSS | power_in | Ground pin, which must always be connected to the ground of the external supply. |
| 48 | VDD | power_in | Main power supply pin operating from 1.71 V to 3.6 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMICROELECTRONICS |
| Package | LQFP-48(7x7) |
| Category | Global Sourcing Parts |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Standard operating voltage (IO_VDD_HSLV = 0) | VDD | 1.71 | 3.6 | V | IO_VDD_HSLV = 0 | 156 | |
| Standard operating voltage (IO_VDD_HSLV = 1) | VDD | 1.71 | 2.7 | V | IO_VDD_HSLV = 1 | 156 | |
| Supply voltage for PG[15:2] I/Os | VDDIO2 | 1.08 | 3.6 | V | At least one I/O in PG[15:2] used, IO_VDDIO2_HSLV = 0 | 156 | |
| Supply voltage for PG[15:2] I/Os (HSLV) | VDDIO2 | 1.08 | 2.7 | V | At least one I/O in PG[15:2] used, IO_VDDIO2_HSLV = 1 | 156 | |
| Supply voltage for PG[15:2] I/Os (not used) | VDDIO2 | 0 | 3.6 | V | PG[15:2] I/Os not used | 156 | |
| USB supply voltage | VDDUSB | 3 | 3.6 | V | USB used | 156 | |
| USB supply voltage (not used) | VDDUSB | 0 | 3.6 | V | USB not used | 156 | |
| Analog supply voltage | VDDA | 1.58 | 3.6 | V | COMP used | 156 | |
| Analog supply voltage | VDDA | 1.6 | 3.6 | V | DAC or OPAMP used | 156 | |
| Analog supply voltage | VDDA | 1.62 | 3.6 | V | ADC used | 156 | |
| Analog supply voltage | VDDA | 1.8 | 3.6 | V | VREFBUF used (normal mode) | 156 | |
| Analog supply voltage (not used) | VDDA | 0 | 3.6 | V | ADC, DAC, COMP, OPAMP, and VREFBUF not used | 156 | |
| Backup domain supply voltage | VBAT | 1.65 | 3.6 | V | 156 | ||
| I/O input voltage | VIN | -0.3 | V | All I/Os except FT_c and TT_xx pins; max is a formula, see review_required | 156 | ||
| Input voltage on FT_t pins in VBAT mode | VIN | -0.3 | V | FT_t pins in VBAT mode; max is a formula, see review_required | 156 | ||
| FT_c I/O input voltage | VIN | -0.3 | 5 | V | FT_c I/Os | 156 | |
| TT_xx I/O input voltage | VIN | -0.3 | V | TT_xx I/Os; max is VDDIOx + 0.3, see review_required | 156 | ||
| Sum of output current sourced by all I/Os powered by VSW | IIO_SW | 3 | mA | 156 | |||
| Internal regulator VCORE | VCORE | 1.15 | 1.21 | 1.27 | V | Internal regulator ON, Range 1 | 157 |
| Internal regulator VCORE | VCORE | 1.05 | 1.1 | 1.15 | V | Internal regulator ON, Range 2 | 157 |
| Internal regulator VCORE | VCORE | 0.95 | 1 | 1.05 | V | Internal regulator ON, Range 3 | 157 |
| Internal regulator VCORE | VCORE | 0.81 | 0.9 | 0.99 | V | Internal regulator ON, Range 4 | 157 |
| AHB clock frequency fHCLK | fHCLK | 160 | MHz | Voltage scaling Range 1 | 157 | ||
| AHB clock frequency fHCLK | fHCLK | 110 | MHz | Voltage scaling Range 2 | 157 | ||
| AHB clock frequency fHCLK | fHCLK | 55 | MHz | Voltage scaling Range 3 | 157 | ||
| AHB clock frequency fHCLK | fHCLK | 25 | MHz | Voltage scaling Range 4 | 157 | ||
| Ambient temperature for suffix 6 (maximum power dissipation) | TA | -40 | 85 | °C | Suffix 6, maximum power dissipation | 158 | |
| Ambient temperature for suffix 6 (low-power dissipation) | TA | -40 | 105 | °C | Suffix 6, low-power dissipation | 158 | |
| Junction temperature range | TJ | -40 | 105 | °C | Suffix 6 version | 158 | |
| Voltage on VDDX - VSS (external main supply) | VDDX - VSS | -0.3 | 4 | V | Includes VDDSMPS, VDDA, VDDUSB, VBAT, VREF+ | 154 | |
| I/O supply VDDIOx - VSS | VDDIOx - VSS | -0.3 | 4 | V | I/O supply when HSLV = 0 | 154 | |
| I/O supply VDDIOx - VSS | VDDIOx - VSS | -0.3 | 2.75 | V | I/O supply when HSLV = 1 | 154 | |
| Input voltage on FT_xx pins except FT_c pins | VIN | -0.3 | V | Max is a formula, see review_required | 154 | ||
| Input voltage on FT_c pins | VIN | -0.3 | 5.5 | V | 154 | ||
| Input voltage on any other pins | VIN | -0.3 | 4 | V | 154 | ||
| Allowed voltage difference for VREF+ > VDDA | VREF+ - VDDA | 0.4 | V | VREF+ > VDDA; printed as '- 0.4', read as max, see review_required | 154 | ||
| Variations between different VDDx power pins of the same domain | /ΔVDDx/ | 50 | mV | 154 | |||
| Variations between all the different ground pins | /VSSx-VSS/ | 50 | mV | Including VREF- pin | 154 | ||
| Total current into sum of all VDD power lines (source) | ∑IVDD | 200 | mA | 154 | |||
| Total current out of sum of all VSS ground lines (sink) | ∑IVSS | 200 | mA | 154 | |||
| Maximum current into each VDD power pin (source) | IVDD | 100 | mA | 154 | |||
| Maximum current out of each VSS ground pin (sink) | IVSS | 100 | mA | 154 | |||
| Output current sunk by any I/O and control pin | IIO | 20 | mA | Sink | 154 | ||
| Output current sourced by any I/O and control pin | IIO | 20 | mA | Source | 154 | ||
| Total output current sunk by sum of all I/Os and control pins | ∑I(PIN) | 120 | mA | Sink | 154 | ||
| Total output current sourced by sum of all I/Os and control pins | ∑I(PIN) | 120 | mA | Source | 154 | ||
| Injected current on FT_xx, TT_xx, RST pins | IINJ(PIN) | -5 | 0 | mA | 154 | ||
| Total injected current (sum of all I/Os and control pins) | ∑/IINJ(PIN)/ | 25 | mA | Printed as ±25; absolute sum of injected currents | 154 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 155 | ||
| Maximum junction temperature | TJ | 140 | °C | 155 | |||
| Embedded brownout reset threshold 0 (rising edge) | VBOR0 | 1.6 | 1.66 | 1.71 | V | Rising edge | 159 |
| Embedded brownout reset threshold 0 (falling edge) | VBOR0 | 1.58 | 1.64 | 1.69 | V | Falling edge, range 1, 2, 3 | 159 |
| VBAT brownout reset threshold | VBOR_VBAT | 1.58 | 1.65 | V | 160 | ||
| Internal reference voltage | VREFINT | 1.175 | 1.215 | 1.255 | V | Range 1, 2, 3 | 161 |
CAD (KiCad official)
- Symbol:
STM32U575CIT6Q - Footprint:
Package_QFP:LQFP-48_7x7mm_P0.5mm - 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
stm32u575cit6q-etched.step/stm32u575cit6q-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32u575cit6q.step/stm32u575cit6q.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMICROELECTRONICS datasheet (346 pp, sha256
f3de0b5e62ad45ed, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).