Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

SST26VF032BEUI-104I

Microchip Tech · EEPROM · SOIC-8-208mil

SST26VF032BEUI-104I from Microchip Tech, in a SOIC-8-208mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CE# input Chip Enable: the device is enabled by a high-to-low transition and CE# must remain low for the duration of any command sequence.
2 SO/SIO1 bidirectional Serial data output in SPI mode (default after Power-On Reset, shifted out on the falling edge of SCK) and serial data I/O 1 in dual/quad I/O mode.
3 WP#/SIO2 bidirectional Write-Protect, used with the WPEN and IOC bits to prohibit writes to the Block Protection register and only working in SPI single-bit and dual-bit read mode; serial data I/O 2 in quad mode.
4 VSS power_in Ground.
5 SI/SIO0 bidirectional Serial data input in SPI mode (default after Power-On Reset, latched on the rising edge of SCK) and serial data I/O 0 in dual/quad I/O mode.
6 SCK input Serial clock that times the serial interface; commands, addresses and input data are latched on the rising edge and output data is shifted out on the falling edge.
7 HOLD#/SIO3 bidirectional Hold pin temporarily stops serial communication while the device is selected, only works in SPI single-bit and dual-bit modes and must be tied high when not in use; serial data I/O 3 in quad mode.
8 VDD power_in Power supply voltage, 2.7V to 3.6V (104 MHz) or 2.3V to 3.6V (80 MHz).

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOIC-8-208mil
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VDD 2.3 3.6 V Operating range, Industrial 42
Ambient temperature (Industrial) TA -40 85 °C Industrial 42
Temperature under bias -55 125 °C 42
Storage temperature -65 150 °C 42
DC voltage on any pin to ground -0.5 V upper limit printed as VDD+0.5V 42
Transient voltage on any pin to ground -2 V < 20 ns; upper limit printed as VDD+2.0V 42
Package power dissipation capability 1 W TA = +25°C 42
Surface mount solder reflow temperature 260 °C 10 seconds 42
Read Current IDDR1 8 15 mA VDD = VDD maximum, CE# = 0.1 VDD/0.9 VDD @40 MHz, SO = open 44
Read Current IDDR2 20 mA VDD = VDD maximum, CE# = 0.1 VDD/0.9 VDD @104 MHz, SO = open 44
Program and Erase Current IDDW1 25 mA CE# = VDD maximum 44
Standby Current ISB1 15 45 µA CE# = VDD, VIN = VDD or VSS 44
Input Leakage Current ILI 2 µA VIN = GND to VDD, VDD = VDD maximum 44
Output Leakage Current ILO 2 µA VOUT = GND to VDD, VDD = VDD maximum 44
Input Low-Voltage VIL 0.8 V VDD = VDD minimum 44
Input High-Voltage VIH 0.7 *VDD VDD = VDD maximum; printed 0.7*VDD 44
Output Low-Voltage VOL 0.2 V IOL = 100 µA, VDD = VDD minimum 44
Output Pin Capacitance COUT 8 pF VOUT = 0V, TA = +25°C, f = 1 MHz 44
Input Capacitance CIN 6 pF VIN = 0V, TA = +25°C, f = 1 MHz 44
Endurance NEND 100000 cycles JEDEC Standard A117 and AEC-Q100-005 44
Data Retention TDR 100 years JEDEC Standard A103 and AEC-Q100-005 44
Sector Erase TSE 25 ms 45
Block Erase TBE 25 ms 45
Chip Erase TSCE 50 ms 45
Page Program TPP 1.5 ms 45
Program Security ID TPSID 1.5 ms 45
Write Suspend Latency TWS 25 µs 45
Write Protection Enable Bit Latency TWPEN 25 ms 45
VDD Minimum to Read Operation TPU-READ 100 µs 42
VDD Minimum to Write Operation TPU-WRITE 100 µs 42
Power-down Duration TPD 100 ms 42
VDD off time VOFF 0.3 V 0V recommended 42
Serial Clock Frequency FCLK 104 MHz 104 MHz column 46
Serial Clock Period TCLK 9.6 ns 104 MHz column, as printed 46
Serial Clock High Time TSCKH 4.5 ns 104 MHz column 46
Serial Clock Low Time TSCKL 4.5 ns 104 MHz column 46
CE# Active Setup Time TCES 5 ns 104 MHz column, relative to SCK 46
CE# Active Hold Time TCEH 5 ns 104 MHz column, relative to SCK 46
CE# Not Active Setup Time TCHS 5 ns 104 MHz column, relative to SCK 46
CE# Not Active Hold Time TCHH 5 ns 104 MHz column, relative to SCK 46
CE# High Time TCPH 12 ns 104 MHz column 46
CE# High to High-Z Output TCHZ 12 ns 104 MHz column 46
SCK Low to Low-Z Output TCLZ 0 ns 104 MHz column 46
HOLD# Low Setup Time THLS 5 ns 104 MHz column 46
HOLD# High Setup Time THHS 5 ns 104 MHz column 46
HOLD# Low Hold Time THLH 5 ns 104 MHz column 46
HOLD# High Hold Time THHH 5 ns 104 MHz column 46
HOLD# Low-to-High-Z Output THZ 8 ns 104 MHz column 46
HOLD# High-to-Low-Z Output TLZ 8 ns 104 MHz column 46
Data In Setup Time TDS 3 ns 104 MHz column 46
Data In Hold Time TDH 4 ns 104 MHz column 46
Output Hold from SCK Change TOH 0 ns 104 MHz column 46

CAD (KiCad official)

  • Symbol: SST26VF032BEUI-104I
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8-208mil (KiCad packages3D, STEP)
  • 3D model files: sst26vf032beui-104i-etched.step / sst26vf032beui-104i-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); sst26vf032beui-104i.step / sst26vf032beui-104i.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (81 pp, sha256 889839aacf54a03d, retrieved 2026-10-23, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF