Generated by kicad-footprint-generator · KiCad file format 20260206
SST26VF032BEUI-104I
Microchip Tech · EEPROM · SOIC-8-208mil
SST26VF032BEUI-104I from Microchip Tech, in a SOIC-8-208mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CE# | input | Chip Enable: the device is enabled by a high-to-low transition and CE# must remain low for the duration of any command sequence. |
| 2 | SO/SIO1 | bidirectional | Serial data output in SPI mode (default after Power-On Reset, shifted out on the falling edge of SCK) and serial data I/O 1 in dual/quad I/O mode. |
| 3 | WP#/SIO2 | bidirectional | Write-Protect, used with the WPEN and IOC bits to prohibit writes to the Block Protection register and only working in SPI single-bit and dual-bit read mode; serial data I/O 2 in quad mode. |
| 4 | VSS | power_in | Ground. |
| 5 | SI/SIO0 | bidirectional | Serial data input in SPI mode (default after Power-On Reset, latched on the rising edge of SCK) and serial data I/O 0 in dual/quad I/O mode. |
| 6 | SCK | input | Serial clock that times the serial interface; commands, addresses and input data are latched on the rising edge and output data is shifted out on the falling edge. |
| 7 | HOLD#/SIO3 | bidirectional | Hold pin temporarily stops serial communication while the device is selected, only works in SPI single-bit and dual-bit modes and must be tied high when not in use; serial data I/O 3 in quad mode. |
| 8 | VDD | power_in | Power supply voltage, 2.7V to 3.6V (104 MHz) or 2.3V to 3.6V (80 MHz). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-8-208mil |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VDD | 2.3 | 3.6 | V | Operating range, Industrial | 42 | |
| Ambient temperature (Industrial) | TA | -40 | 85 | °C | Industrial | 42 | |
| Temperature under bias | -55 | 125 | °C | 42 | |||
| Storage temperature | -65 | 150 | °C | 42 | |||
| DC voltage on any pin to ground | -0.5 | V | upper limit printed as VDD+0.5V | 42 | |||
| Transient voltage on any pin to ground | -2 | V | < 20 ns; upper limit printed as VDD+2.0V | 42 | |||
| Package power dissipation capability | 1 | W | TA = +25°C | 42 | |||
| Surface mount solder reflow temperature | 260 | °C | 10 seconds | 42 | |||
| Read Current | IDDR1 | 8 | 15 | mA | VDD = VDD maximum, CE# = 0.1 VDD/0.9 VDD @40 MHz, SO = open | 44 | |
| Read Current | IDDR2 | 20 | mA | VDD = VDD maximum, CE# = 0.1 VDD/0.9 VDD @104 MHz, SO = open | 44 | ||
| Program and Erase Current | IDDW1 | 25 | mA | CE# = VDD maximum | 44 | ||
| Standby Current | ISB1 | 15 | 45 | µA | CE# = VDD, VIN = VDD or VSS | 44 | |
| Input Leakage Current | ILI | 2 | µA | VIN = GND to VDD, VDD = VDD maximum | 44 | ||
| Output Leakage Current | ILO | 2 | µA | VOUT = GND to VDD, VDD = VDD maximum | 44 | ||
| Input Low-Voltage | VIL | 0.8 | V | VDD = VDD minimum | 44 | ||
| Input High-Voltage | VIH | 0.7 | *VDD | VDD = VDD maximum; printed 0.7*VDD | 44 | ||
| Output Low-Voltage | VOL | 0.2 | V | IOL = 100 µA, VDD = VDD minimum | 44 | ||
| Output Pin Capacitance | COUT | 8 | pF | VOUT = 0V, TA = +25°C, f = 1 MHz | 44 | ||
| Input Capacitance | CIN | 6 | pF | VIN = 0V, TA = +25°C, f = 1 MHz | 44 | ||
| Endurance | NEND | 100000 | cycles | JEDEC Standard A117 and AEC-Q100-005 | 44 | ||
| Data Retention | TDR | 100 | years | JEDEC Standard A103 and AEC-Q100-005 | 44 | ||
| Sector Erase | TSE | 25 | ms | 45 | |||
| Block Erase | TBE | 25 | ms | 45 | |||
| Chip Erase | TSCE | 50 | ms | 45 | |||
| Page Program | TPP | 1.5 | ms | 45 | |||
| Program Security ID | TPSID | 1.5 | ms | 45 | |||
| Write Suspend Latency | TWS | 25 | µs | 45 | |||
| Write Protection Enable Bit Latency | TWPEN | 25 | ms | 45 | |||
| VDD Minimum to Read Operation | TPU-READ | 100 | µs | 42 | |||
| VDD Minimum to Write Operation | TPU-WRITE | 100 | µs | 42 | |||
| Power-down Duration | TPD | 100 | ms | 42 | |||
| VDD off time | VOFF | 0.3 | V | 0V recommended | 42 | ||
| Serial Clock Frequency | FCLK | 104 | MHz | 104 MHz column | 46 | ||
| Serial Clock Period | TCLK | 9.6 | ns | 104 MHz column, as printed | 46 | ||
| Serial Clock High Time | TSCKH | 4.5 | ns | 104 MHz column | 46 | ||
| Serial Clock Low Time | TSCKL | 4.5 | ns | 104 MHz column | 46 | ||
| CE# Active Setup Time | TCES | 5 | ns | 104 MHz column, relative to SCK | 46 | ||
| CE# Active Hold Time | TCEH | 5 | ns | 104 MHz column, relative to SCK | 46 | ||
| CE# Not Active Setup Time | TCHS | 5 | ns | 104 MHz column, relative to SCK | 46 | ||
| CE# Not Active Hold Time | TCHH | 5 | ns | 104 MHz column, relative to SCK | 46 | ||
| CE# High Time | TCPH | 12 | ns | 104 MHz column | 46 | ||
| CE# High to High-Z Output | TCHZ | 12 | ns | 104 MHz column | 46 | ||
| SCK Low to Low-Z Output | TCLZ | 0 | ns | 104 MHz column | 46 | ||
| HOLD# Low Setup Time | THLS | 5 | ns | 104 MHz column | 46 | ||
| HOLD# High Setup Time | THHS | 5 | ns | 104 MHz column | 46 | ||
| HOLD# Low Hold Time | THLH | 5 | ns | 104 MHz column | 46 | ||
| HOLD# High Hold Time | THHH | 5 | ns | 104 MHz column | 46 | ||
| HOLD# Low-to-High-Z Output | THZ | 8 | ns | 104 MHz column | 46 | ||
| HOLD# High-to-Low-Z Output | TLZ | 8 | ns | 104 MHz column | 46 | ||
| Data In Setup Time | TDS | 3 | ns | 104 MHz column | 46 | ||
| Data In Hold Time | TDH | 4 | ns | 104 MHz column | 46 | ||
| Output Hold from SCK Change | TOH | 0 | ns | 104 MHz column | 46 |
CAD (KiCad official)
- Symbol:
SST26VF032BEUI-104I - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8-208mil (KiCad packages3D, STEP)
- 3D model files:
sst26vf032beui-104i-etched.step/sst26vf032beui-104i-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sst26vf032beui-104i.step/sst26vf032beui-104i.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (81 pp, sha256
889839aacf54a03d, retrieved 2026-10-23, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).