Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

STM32WB55RGV7

STMicroelectronics · RF Transceiver ICs · QFN-68-EP(8x8)

STM32WB55RGV7 from STMicroelectronics, in a QFN-68-EP(8x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VBAT power_in Backup-domain supply (1.55 to 3.6 V) that powers the RTC, LSE and backup registers when VDD is not present.
2 PC13 bidirectional 5 V-tolerant GPIO supplied through the power switch, which sinks only 3 mA, so output speed is limited to 2 MHz with 30 pF and it must not source LEDs; also RTC_TAMP1/RTC_TS/RTC_OUT/WKUP2.
3 PC14-OSC32_IN bidirectional GPIO supplied through the power switch (3 mA sink limit, 2 MHz / 30 pF output limit, no current-source use) that doubles as the LSE oscillator input OSC32_IN.
4 PC15-OSC32_OUT bidirectional GPIO supplied through the power switch (3 mA sink limit, 2 MHz / 30 pF output limit, no current-source use) that doubles as the LSE oscillator output OSC32_OUT.
5 PH3-BOOT0 bidirectional 5 V-tolerant I/O shared with the BOOT0 boot-mode function and the LSCO clock output (available in Run and Stop modes).
6 PB8 bidirectional 5 V-tolerant I/O, Fm+ capable and with LCD function supplied by VLCD; alternate functions include TIM1_CH2N, I2C1_SCL, QUADSPI_BK1_IO1, LCD_SEG16 and TIM16_CH1.
7 PB9 bidirectional 5 V-tolerant I/O, Fm+ capable, with analog switch function supplied by VDDA; alternate functions include I2C1_SDA, SPI2_NSS, IR_OUT, QUADSPI_BK1_IO0, LCD_COM3 and TIM17_CH1.
8 NRST bidirectional Bidirectional reset pin with weak internal pull-up resistor (RST structure), with the internal reset pull-up deactivated when the reset source is internal.
9 PC0 bidirectional 5 V-tolerant I/O with analog switch function supplied by VDDA; alternate functions include LPTIM1_IN1, I2C3_SCL, LPUART1_RX and LPTIM2_IN1, and additional function ADC1_IN1.
10 PC1 bidirectional 5 V-tolerant I/O with analog switch function supplied by VDDA; alternate functions include LPTIM1_OUT, SPI2_MOSI, I2C3_SDA, LPUART1_TX and LCD_SEG19, and additional function ADC1_IN2.
11 PC2 bidirectional 5 V-tolerant I/O with LCD function supplied by VLCD and analog switch function supplied by VDDA; alternate functions include LPTIM1_IN2, SPI2_MISO and LCD_SEG20, and additional function ADC1_IN3.
12 PC3 bidirectional 5 V-tolerant I/O with analog switch function supplied by VDDA; alternate functions include LPTIM1_ETR, SAI1_PDM_DI1, SPI2_MOSI, LCD_VLCD and SAI1_SD_A, and additional function ADC1_IN4.
13 VREF+ power_in Positive reference voltage for the ADC (2 V up to VDDA when VDDA is 2 V or higher) and the VREFBUF_OUT buffered output; VREF+ must not exceed VDDA by more than 0.4 V.
14 VDDA power_in Analog supply for the ADC, comparators and voltage reference buffer, 1.62 to 3.6 V (2.4 V minimum when VREFBUF is used), connected to VDD when unused.
15 PA0 bidirectional 5 V-tolerant I/O with analog switch function supplied by VDDA; alternate functions include TIM2_CH1, COMP1_OUT, SAI1_EXTCLK and TIM2_ETR, and additional functions COMP1_INM, ADC1_IN5 and RTC_TAMP2/WKUP1.
16 PA1 bidirectional 5 V-tolerant I/O with LCD function supplied by VLCD and analog switch function supplied by VDDA; alternate functions include TIM2_CH2, I2C1_SMBA, SPI1_SCK and LCD_SEG0, and additional functions COMP1_INP and ADC1_IN6.
17 PA2 bidirectional 5 V-tolerant I/O with LCD and analog switch functions; alternate functions include LSCO, TIM2_CH3, LPUART1_TX, QUADSPI_BK1_NCS and COMP2_OUT, and additional functions COMP2_INM, ADC1_IN7 and WKUP4 (Standby/Shutdown wakeup).
18 PA3 bidirectional 5 V-tolerant I/O with LCD and analog switch functions; alternate functions include TIM2_CH4, SAI1_PDM_CK1, LPUART1_RX, QUADSPI_CLK and LCD_SEG2, and additional functions COMP2_INP and ADC1_IN8.
19 PA4 bidirectional 5 V-tolerant I/O with analog switch function supplied by VDDA; alternate functions include SPI1_NSS, SAI1_FS_B, LPTIM2_OUT and LCD_SEG5, and additional functions COMP1_INM, COMP2_INM and ADC1_IN9.
20 PA5 bidirectional 5 V-tolerant I/O with analog switch function supplied by VDDA; alternate functions include TIM2_CH1, TIM2_ETR, SPI1_SCK, LPTIM2_ETR and SAI1_SD_B, and additional functions COMP1_INM, COMP2_INM and ADC1_IN10.
21 PA6 bidirectional 5 V-tolerant I/O with LCD and analog switch functions; alternate functions include TIM1_BKIN, SPI1_MISO, LPUART1_CTS, QUADSPI_BK1_IO3, LCD_SEG3 and TIM16_CH1, and additional function ADC1_IN11.
22 PA7 bidirectional 5 V-tolerant Fm+-capable I/O with analog switch function supplied by VDDA; alternate functions include TIM1_CH1N, I2C3_SCL, SPI1_MOSI, QUADSPI_BK1_IO2, COMP2_OUT and TIM17_CH1, and additional function ADC1_IN12.
23 PA8 bidirectional 5 V-tolerant I/O with LCD and analog switch functions; alternate functions include MCO, TIM1_CH1, SAI1_PDM_CK2, USART1_CK, LCD_COM0 and LPTIM2_OUT, and additional function ADC1_IN15.
24 PA9 bidirectional 5 V-tolerant Fm+-capable I/O with analog switch function supplied by VDDA; alternate functions include TIM1_CH2, I2C1_SCL, SPI2_SCK, USART1_TX and LCD_COM1, and additional functions COMP1_INM and ADC1_IN16.
25 PC4 bidirectional 5 V-tolerant I/O with LCD and analog switch functions; alternate function CM4_EVENTOUT and LCD_SEG22, with additional functions COMP1_INM and ADC1_IN13.
26 PC5 bidirectional 5 V-tolerant I/O with LCD and analog switch functions; alternate functions include SAI1_PDM_DI3 and LCD_SEG23, and additional functions COMP1_INP, ADC1_IN14 and WKUP5 (Standby/Shutdown wakeup).
27 PB2 bidirectional 5 V-tolerant I/O with LCD (VLCD) and analog switch functions; alternate functions include RTC_OUT, LPTIM1_OUT, I2C3_SMBA, SPI1_NSS and SAI1_EXTCLK, and additional function COMP1_INP.
28 PB10 bidirectional 5 V-tolerant Fm+-capable I/O with LCD function supplied by VLCD; alternate functions include TIM2_CH3, I2C3_SCL, SPI2_SCK, LPUART1_RX, TSC_SYNC, QUADSPI_CLK, LCD_SEG10 and COMP1_OUT.
29 PB11 bidirectional 5 V-tolerant Fm+-capable I/O with LCD function supplied by VLCD; alternate functions include TIM2_CH4, I2C3_SDA, LPUART1_TX, QUADSPI_BK1_NCS, LCD_SEG11 and COMP2_OUT.
30 VDD power_in Main supply, 1.71 to 3.6 V for I/Os, the internal regulator and the RF, SMPS and clock functions; VDD, VDDRF and VDDSMPS must be wired together.
31 RF1 bidirectional RF input/output that must be connected to the antenna through a low-pass matching network, using the nominal PCB layout.
32 VSSRF power_in RF ground that must be connected to GND, and the exposed pad must be connected to the GND plane for correct RF operation.
33 VDDRF power_in Dedicated RF supply, 1.71 to 3.6 V, that must always be connected to VDD.
34 OSC_OUT output 32 MHz main oscillator output, also used as the HSE source, to be laid out per the reference design (AN5165).
35 OSC_IN input 32 MHz main oscillator input, also used as the HSE source, to be laid out per the reference design (AN5165).
36 AT0 output Reserved RF pin that must be kept unconnected.
37 AT1 output Reserved RF pin that must be kept unconnected.
38 PB0 bidirectional 3.6 V-tolerant (TT) I/O with alternate functions COMP1_OUT and EXT_PA_TX (external PA transmit control); output speed must be set to 00 during RF operation because higher frequencies impact RF performance.
39 PB1 bidirectional 3.6 V-tolerant (TT) I/O with alternate functions LPUART1_RTS_DE and LPTIM2_IN1; output speed must be set to 00 during RF operation because higher frequencies impact RF performance.
40 PE4 bidirectional 5 V-tolerant (FT) I/O with CM4_EVENTOUT as its only listed alternate function.
41 VFBSMPS power_in SMPS feedback voltage input, 1.4 to 3.6 V.
42 VSSSMPS power_in Ground pin of the SMPS step-down converter, to be connected to GND.
43 VLXSMPS power_in SMPS switching node that connects to the external inductor L1 (2.2 µH for 8 MHz or 10 µH for 4 MHz operation) with 4.7 µF output capacitor C2.
44 VDDSMPS power_in SMPS input supply that must always be connected to VDD.
45 VDD power_in Supply pin, 1.71 to 3.6 V, that must be wired together with VDDRF and VDDSMPS.
46 PB12 bidirectional 5 V-tolerant I/O with LCD function supplied by VLCD; alternate functions include TIM1_BKIN, I2C3_SMBA, SPI2_NSS, LPUART1_RTS, TSC_G1_IO1, LCD_SEG12 and SAI1_FS_A.
47 PB13 bidirectional 5 V-tolerant Fm+-capable I/O with LCD function supplied by VLCD; alternate functions include TIM1_CH1N, I2C3_SCL, SPI2_SCK, LPUART1_CTS, TSC_G1_IO2, LCD_SEG13 and SAI1_SCK_A.
48 PB14 bidirectional 5 V-tolerant Fm+-capable I/O with LCD function supplied by VLCD; alternate functions include TIM1_CH2N, I2C3_SDA, SPI2_MISO, TSC_G1_IO3, LCD_SEG14 and SAI1_MCLK_A.
49 PB15 bidirectional 5 V-tolerant I/O with LCD function supplied by VLCD; alternate functions include RTC_REFIN, TIM1_CH3N, SPI2_MOSI, TSC_G1_IO4, LCD_SEG15 and SAI1_SD_A.
50 PC6 bidirectional 5 V-tolerant I/O with LCD function supplied by VLCD; alternate functions include TSC_G4_IO1 and LCD_SEG24.
51 PA10 bidirectional 5 V-tolerant Fm+-capable I/O with LCD function supplied by VLCD; alternate functions include TIM1_CH3, SAI1_PDM_DI1, I2C1_SDA, USART1_RX, USB_CRS_SYNC, LCD_COM2, SAI1_SD_A and TIM17_BKIN.
52 PA11 bidirectional 5 V-tolerant I/O with USB function supplied by VDDA-independent VDDUSB when USB alternate function is selected; alternate functions include TIM1_CH4, TIM1_BKIN2, SPI1_MISO, USART1_CTS and USB_DM.
53 PA12 bidirectional 5 V-tolerant I/O with USB function supplied by VDDUSB when USB alternate function is selected; alternate functions include TIM1_ETR, SPI1_MOSI, LPUART1_RX, USART1_RTS_DE and USB_DP.
54 PA13 bidirectional 5 V-tolerant I/O that after reset is configured as JTMS-SWDIO with an internal pull-up enabled; other alternate functions include IR_OUT, USB_NOE and SAI1_SD_B.
55 VDDUSB power_in USB transceiver supply, 3.0 to 3.6 V when USB is used, and connected to VDD when USB is not used.
56 PA14 bidirectional 5 V-tolerant I/O that after reset is configured as JTCK-SWCLK with an internal pull-down enabled; other alternate functions include LPTIM1_OUT, I2C1_SMBA, LCD_SEG5 and SAI1_FS_B.
57 PA15 bidirectional 5 V-tolerant I/O that after reset is configured as JTDI with an internal pull-up enabled; other alternate functions include TIM2_CH1, TIM2_ETR, SPI1_NSS, TSC_G3_IO1, LCD_SEG17 and MCO.
58 PC10 bidirectional 5 V-tolerant I/O with LCD function supplied by VLCD; alternate functions include TRACED1, TSC_G3_IO2 and LCD_COM4/LCD_SEG28/LCD_SEG40.
59 PC11 bidirectional 5 V-tolerant I/O with LCD function supplied by VLCD; alternate functions include TSC_G3_IO3 and LCD_COM5/LCD_SEG29/LCD_SEG41.
60 PC12 bidirectional 5 V-tolerant I/O with LCD function supplied by VLCD; alternate functions include LSCO, TRACED3, TSC_G3_IO4 and LCD_COM6/LCD_SEG30/LCD_SEG42, and additional function RTC_TAMP3/WKUP3.
61 PD0 bidirectional 5 V-tolerant I/O with alternate functions SPI2_NSS and CM4_EVENTOUT.
62 PD1 bidirectional 5 V-tolerant I/O with alternate functions SPI2_SCK and CM4_EVENTOUT.
63 PB3 bidirectional 5 V-tolerant I/O with LCD and analog switch functions that after reset is configured as JTDO-TRACESWO; other alternate functions include TIM2_CH2, SPI1_SCK, USART1_RTS_DE and SAI1_SCK_B, and additional function COMP2_INM.
64 PB4 bidirectional 5 V-tolerant I/O with analog switch function supplied by VDDA that after reset is configured as NJTRST with an internal pull-up enabled; other alternate functions include I2C3_SDA, SPI1_MISO, USART1_CTS and TIM17_BKIN, and additional function COMP2_INP.
65 PB5 bidirectional 5 V-tolerant I/O with LCD function supplied by VLCD; alternate functions include LPTIM1_IN1, I2C1_SMBA, SPI1_MOSI, USART1_CK, LPUART1_TX, LCD_SEG9, COMP2_OUT and TIM16_BKIN.
66 PB6 bidirectional 5 V-tolerant Fm+-capable I/O with LCD and analog switch functions; alternate functions include LPTIM1_ETR, I2C1_SCL, USART1_TX, LCD_SEG6, SAI1_FS_B, TIM16_CH1N and MCO, and additional function COMP2_INP.
67 PB7 bidirectional 5 V-tolerant Fm+-capable I/O with LCD and analog switch functions; alternate functions include LPTIM1_IN2, TIM1_BKIN, I2C1_SDA, USART1_RX, LCD_SEG21 and TIM17_CH1N, and additional functions COMP2_INM and PVD_IN.
68 VDD power_in Supply pin, 1.71 to 3.6 V, that must be wired together with VDDRF and VDDSMPS.
69 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package QFN-68-EP(8x8)
Category RF & Radio
Pins 69

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
External main supply voltage VDDX - VSS -0.3 4 V Including VDD, VDDA, VDDUSB, VLCD, VDDRF, VDDSMPS, VBAT, VREF+ 85
Input voltage on FT_xxx pins VIN -0.3 V 85
Input voltage on TT_xx pins VIN 4 V 85
Input voltage on any other pin VIN 4 V 85
Variations between different VDDX power pins of the same domain /ΔVDDx/ 50 mV 85
Variations between all the different ground pins /VSSx-VSS/ 50 mV 85
Allowed voltage difference for VREF+ > VDDA VREF+ - VDDA 0.4 V 85
Total current into sum of all VDD power lines (source) ∑IVDD 130 mA 85
Total current out of sum of all VSS ground lines (sink) ∑IVSS 130 mA 85
Maximum current into each VDD power pin (source) IVDD(PIN) 100 mA 85
Maximum current out of each VSS ground pin (sink) IVSS(PIN) 100 mA 85
Output current sunk by any I/O and control pin except FT_f IIO(PIN) 20 mA 85
Output current sunk by any FT_f pin IIO(PIN) 20 mA 85
Output current sourced by any I/O and control pin IIO(PIN) 20 mA 85
Total output current sunk by sum of all I/Os and control pins ∑IIO(PIN) 100 mA 85
Total output current sourced by sum of all I/Os and control pins ∑IIO(PIN) 100 mA 85
Injected current on FT_xxx, TT_xx, RST and B pins, except PB0 and PB1 IINJ(PIN) -5 0 mA 85
Injected current on PB0 and PB1 IINJ(PIN) -5 0 mA 85
Total injected current (sum of all I/Os and control pins) ∑/IINJ(PIN)/ 25 mA 85
Storage temperature range TSTG -65 150 °C 86
Maximum junction temperature TJ 130 °C 86
Internal AHB clock frequency fHCLK 0 64 MHz 87
Internal APB1 clock frequency fPCLK1 0 64 MHz 87
Internal APB2 clock frequency fPCLK2 0 64 MHz 87
Standard operating voltage VDD 1.71 3.6 V 87
Analog supply voltage, ADC or COMP used VDDA 1.62 3.6 V ADC or COMP used 87
Analog supply voltage, VREFBUF used VDDA 2.4 V VREFBUF used 87
Backup operating voltage VBAT 1.55 3.6 V 87
SMPS feedback voltage VFBSMPS 1.4 3.6 V 88
Minimum RF voltage VDDRF 1.71 3.6 V 88
USB supply voltage, USB used VDDUSB 3 3.6 V USB used 88
USB supply voltage, USB not used VDDUSB 0 3.6 V USB not used 88
I/O input voltage, TT_xx VIN -0.3 V 88
I/O input voltage, all I/O except TT_xx VIN -0.3 V 88
Power dissipation, VFQFPN68 PD 425 mW TA = 85 °C for suffix 6 or TA = 105 °C for suffix 7 88
Ambient temperature for the suffix 7 version, maximum power dissipation TA -40 105 °C Maximum power dissipation 88
Ambient temperature for the suffix 7 version, low-power dissipation TA 125 °C Low-power dissipation 88
Junction temperature range, suffix 7 version TJ -40 125 °C Suffix 7 version 88
Frequency operating range (BLE) Fop 2402 2480 MHz 88
Frequency operating range (802.15.4) Fop 2405 2480 MHz 93
Frequency drift (BLE 1 Mbps) fd -50 50 kHz Bluetooth Low Energy: ±50 kHz 89
Maximum drift rate (BLE 1 Mbps) maxdr -20 20 kHz/50 µs Bluetooth Low Energy: ±20 kHz / 50 µs 89
Frequency offset (BLE 1 Mbps) fo -150 150 kHz Bluetooth Low Energy: ±150 kHz 89
Frequency deviation average (BLE 1 Mbps) ∆f1 225 275 kHz Bluetooth Low Energy: between 225 and 275 kHz 89
Frequency deviation ratio ∆f2 (average) / ∆f1 (average) (BLE 1 Mbps) ∆f2/∆f1 0.8 Bluetooth Low Energy: > 0.80 89
VDD fall time rate tVDD 10 µs/V VDD fall time rate 96
Reset temporization after BOR0 is detected tRSTTEMPO 250 400 µs VDD rising 96
Brown-out reset threshold 0, rising edge VBOR0 1.62 1.66 1.7 V Rising edge 96
Brown-out reset threshold 0, falling edge VBOR0 1.6 1.64 1.69 V Falling edge 96
Internal reference voltage VREFINT 1.182 1.212 1.232 V -40 °C < TA < +125 °C 98
Internal reference voltage spread over the temperature range ∆VREFINT 5 7.5 mV VDD = 3 V 98
Temperature coefficient TCoeff 30 50 ppm/°C -40 °C < TA < +125 °C 98
Voltage coefficient VDDCoeff 250 1200 ppm/V 3.0 V < VDD < 3.6 V 98
1/4 reference voltage VREFINT_DIV1 24 25 26 % 98
1/2 reference voltage VREFINT_DIV2 49 50 51 % 98
3/4 reference voltage VREFINT_DIV3 74 75 76 % 98
Start time of reference voltage buffer when ADC is enabled tstart_vrefint 8 12 µs 98
Supply current in Run mode, range 1, 64 MHz IDD(Run) 8.15 9.3 mA Range 1, fHCLK = 64 MHz, all peripherals disabled, 25 °C 100
Supply current in Stop 2 mode, RTC disabled, LCD disabled, BLE disabled IDD(Stop 2) 52 135.6 µA VDD = 3.0 V, 105 °C 105
Supply current in Stop 1 mode, RTC disabled, BLE disabled, LCD disabled IDD(Stop 1) 215 746 µA VDD = 3.0 V, 105 °C 107

CAD (KiCad official)

  • Symbol: STM32WB55RGV7
  • Footprint: Package_DFN_QFN:QFN-68-1EP_8x8mm_P0.4mm_EP5.2x5.2mm
  • 3D model: QFN-68-EP(8x8) (KiCad packages3D, STEP)
  • 3D model files: stm32wb55rgv7-etched.step / stm32wb55rgv7-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm32wb55rgv7.step / stm32wb55rgv7.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (193 pp, sha256 dfe954666bc00fe6, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF