Generated by kicad-footprint-generator · KiCad file format 20260206
STM32WB55RGV7
STMicroelectronics · RF Transceiver ICs · QFN-68-EP(8x8)
STM32WB55RGV7 from STMicroelectronics, in a QFN-68-EP(8x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup-domain supply (1.55 to 3.6 V) that powers the RTC, LSE and backup registers when VDD is not present. |
| 2 | PC13 | bidirectional | 5 V-tolerant GPIO supplied through the power switch, which sinks only 3 mA, so output speed is limited to 2 MHz with 30 pF and it must not source LEDs; also RTC_TAMP1/RTC_TS/RTC_OUT/WKUP2. |
| 3 | PC14-OSC32_IN | bidirectional | GPIO supplied through the power switch (3 mA sink limit, 2 MHz / 30 pF output limit, no current-source use) that doubles as the LSE oscillator input OSC32_IN. |
| 4 | PC15-OSC32_OUT | bidirectional | GPIO supplied through the power switch (3 mA sink limit, 2 MHz / 30 pF output limit, no current-source use) that doubles as the LSE oscillator output OSC32_OUT. |
| 5 | PH3-BOOT0 | bidirectional | 5 V-tolerant I/O shared with the BOOT0 boot-mode function and the LSCO clock output (available in Run and Stop modes). |
| 6 | PB8 | bidirectional | 5 V-tolerant I/O, Fm+ capable and with LCD function supplied by VLCD; alternate functions include TIM1_CH2N, I2C1_SCL, QUADSPI_BK1_IO1, LCD_SEG16 and TIM16_CH1. |
| 7 | PB9 | bidirectional | 5 V-tolerant I/O, Fm+ capable, with analog switch function supplied by VDDA; alternate functions include I2C1_SDA, SPI2_NSS, IR_OUT, QUADSPI_BK1_IO0, LCD_COM3 and TIM17_CH1. |
| 8 | NRST | bidirectional | Bidirectional reset pin with weak internal pull-up resistor (RST structure), with the internal reset pull-up deactivated when the reset source is internal. |
| 9 | PC0 | bidirectional | 5 V-tolerant I/O with analog switch function supplied by VDDA; alternate functions include LPTIM1_IN1, I2C3_SCL, LPUART1_RX and LPTIM2_IN1, and additional function ADC1_IN1. |
| 10 | PC1 | bidirectional | 5 V-tolerant I/O with analog switch function supplied by VDDA; alternate functions include LPTIM1_OUT, SPI2_MOSI, I2C3_SDA, LPUART1_TX and LCD_SEG19, and additional function ADC1_IN2. |
| 11 | PC2 | bidirectional | 5 V-tolerant I/O with LCD function supplied by VLCD and analog switch function supplied by VDDA; alternate functions include LPTIM1_IN2, SPI2_MISO and LCD_SEG20, and additional function ADC1_IN3. |
| 12 | PC3 | bidirectional | 5 V-tolerant I/O with analog switch function supplied by VDDA; alternate functions include LPTIM1_ETR, SAI1_PDM_DI1, SPI2_MOSI, LCD_VLCD and SAI1_SD_A, and additional function ADC1_IN4. |
| 13 | VREF+ | power_in | Positive reference voltage for the ADC (2 V up to VDDA when VDDA is 2 V or higher) and the VREFBUF_OUT buffered output; VREF+ must not exceed VDDA by more than 0.4 V. |
| 14 | VDDA | power_in | Analog supply for the ADC, comparators and voltage reference buffer, 1.62 to 3.6 V (2.4 V minimum when VREFBUF is used), connected to VDD when unused. |
| 15 | PA0 | bidirectional | 5 V-tolerant I/O with analog switch function supplied by VDDA; alternate functions include TIM2_CH1, COMP1_OUT, SAI1_EXTCLK and TIM2_ETR, and additional functions COMP1_INM, ADC1_IN5 and RTC_TAMP2/WKUP1. |
| 16 | PA1 | bidirectional | 5 V-tolerant I/O with LCD function supplied by VLCD and analog switch function supplied by VDDA; alternate functions include TIM2_CH2, I2C1_SMBA, SPI1_SCK and LCD_SEG0, and additional functions COMP1_INP and ADC1_IN6. |
| 17 | PA2 | bidirectional | 5 V-tolerant I/O with LCD and analog switch functions; alternate functions include LSCO, TIM2_CH3, LPUART1_TX, QUADSPI_BK1_NCS and COMP2_OUT, and additional functions COMP2_INM, ADC1_IN7 and WKUP4 (Standby/Shutdown wakeup). |
| 18 | PA3 | bidirectional | 5 V-tolerant I/O with LCD and analog switch functions; alternate functions include TIM2_CH4, SAI1_PDM_CK1, LPUART1_RX, QUADSPI_CLK and LCD_SEG2, and additional functions COMP2_INP and ADC1_IN8. |
| 19 | PA4 | bidirectional | 5 V-tolerant I/O with analog switch function supplied by VDDA; alternate functions include SPI1_NSS, SAI1_FS_B, LPTIM2_OUT and LCD_SEG5, and additional functions COMP1_INM, COMP2_INM and ADC1_IN9. |
| 20 | PA5 | bidirectional | 5 V-tolerant I/O with analog switch function supplied by VDDA; alternate functions include TIM2_CH1, TIM2_ETR, SPI1_SCK, LPTIM2_ETR and SAI1_SD_B, and additional functions COMP1_INM, COMP2_INM and ADC1_IN10. |
| 21 | PA6 | bidirectional | 5 V-tolerant I/O with LCD and analog switch functions; alternate functions include TIM1_BKIN, SPI1_MISO, LPUART1_CTS, QUADSPI_BK1_IO3, LCD_SEG3 and TIM16_CH1, and additional function ADC1_IN11. |
| 22 | PA7 | bidirectional | 5 V-tolerant Fm+-capable I/O with analog switch function supplied by VDDA; alternate functions include TIM1_CH1N, I2C3_SCL, SPI1_MOSI, QUADSPI_BK1_IO2, COMP2_OUT and TIM17_CH1, and additional function ADC1_IN12. |
| 23 | PA8 | bidirectional | 5 V-tolerant I/O with LCD and analog switch functions; alternate functions include MCO, TIM1_CH1, SAI1_PDM_CK2, USART1_CK, LCD_COM0 and LPTIM2_OUT, and additional function ADC1_IN15. |
| 24 | PA9 | bidirectional | 5 V-tolerant Fm+-capable I/O with analog switch function supplied by VDDA; alternate functions include TIM1_CH2, I2C1_SCL, SPI2_SCK, USART1_TX and LCD_COM1, and additional functions COMP1_INM and ADC1_IN16. |
| 25 | PC4 | bidirectional | 5 V-tolerant I/O with LCD and analog switch functions; alternate function CM4_EVENTOUT and LCD_SEG22, with additional functions COMP1_INM and ADC1_IN13. |
| 26 | PC5 | bidirectional | 5 V-tolerant I/O with LCD and analog switch functions; alternate functions include SAI1_PDM_DI3 and LCD_SEG23, and additional functions COMP1_INP, ADC1_IN14 and WKUP5 (Standby/Shutdown wakeup). |
| 27 | PB2 | bidirectional | 5 V-tolerant I/O with LCD (VLCD) and analog switch functions; alternate functions include RTC_OUT, LPTIM1_OUT, I2C3_SMBA, SPI1_NSS and SAI1_EXTCLK, and additional function COMP1_INP. |
| 28 | PB10 | bidirectional | 5 V-tolerant Fm+-capable I/O with LCD function supplied by VLCD; alternate functions include TIM2_CH3, I2C3_SCL, SPI2_SCK, LPUART1_RX, TSC_SYNC, QUADSPI_CLK, LCD_SEG10 and COMP1_OUT. |
| 29 | PB11 | bidirectional | 5 V-tolerant Fm+-capable I/O with LCD function supplied by VLCD; alternate functions include TIM2_CH4, I2C3_SDA, LPUART1_TX, QUADSPI_BK1_NCS, LCD_SEG11 and COMP2_OUT. |
| 30 | VDD | power_in | Main supply, 1.71 to 3.6 V for I/Os, the internal regulator and the RF, SMPS and clock functions; VDD, VDDRF and VDDSMPS must be wired together. |
| 31 | RF1 | bidirectional | RF input/output that must be connected to the antenna through a low-pass matching network, using the nominal PCB layout. |
| 32 | VSSRF | power_in | RF ground that must be connected to GND, and the exposed pad must be connected to the GND plane for correct RF operation. |
| 33 | VDDRF | power_in | Dedicated RF supply, 1.71 to 3.6 V, that must always be connected to VDD. |
| 34 | OSC_OUT | output | 32 MHz main oscillator output, also used as the HSE source, to be laid out per the reference design (AN5165). |
| 35 | OSC_IN | input | 32 MHz main oscillator input, also used as the HSE source, to be laid out per the reference design (AN5165). |
| 36 | AT0 | output | Reserved RF pin that must be kept unconnected. |
| 37 | AT1 | output | Reserved RF pin that must be kept unconnected. |
| 38 | PB0 | bidirectional | 3.6 V-tolerant (TT) I/O with alternate functions COMP1_OUT and EXT_PA_TX (external PA transmit control); output speed must be set to 00 during RF operation because higher frequencies impact RF performance. |
| 39 | PB1 | bidirectional | 3.6 V-tolerant (TT) I/O with alternate functions LPUART1_RTS_DE and LPTIM2_IN1; output speed must be set to 00 during RF operation because higher frequencies impact RF performance. |
| 40 | PE4 | bidirectional | 5 V-tolerant (FT) I/O with CM4_EVENTOUT as its only listed alternate function. |
| 41 | VFBSMPS | power_in | SMPS feedback voltage input, 1.4 to 3.6 V. |
| 42 | VSSSMPS | power_in | Ground pin of the SMPS step-down converter, to be connected to GND. |
| 43 | VLXSMPS | power_in | SMPS switching node that connects to the external inductor L1 (2.2 µH for 8 MHz or 10 µH for 4 MHz operation) with 4.7 µF output capacitor C2. |
| 44 | VDDSMPS | power_in | SMPS input supply that must always be connected to VDD. |
| 45 | VDD | power_in | Supply pin, 1.71 to 3.6 V, that must be wired together with VDDRF and VDDSMPS. |
| 46 | PB12 | bidirectional | 5 V-tolerant I/O with LCD function supplied by VLCD; alternate functions include TIM1_BKIN, I2C3_SMBA, SPI2_NSS, LPUART1_RTS, TSC_G1_IO1, LCD_SEG12 and SAI1_FS_A. |
| 47 | PB13 | bidirectional | 5 V-tolerant Fm+-capable I/O with LCD function supplied by VLCD; alternate functions include TIM1_CH1N, I2C3_SCL, SPI2_SCK, LPUART1_CTS, TSC_G1_IO2, LCD_SEG13 and SAI1_SCK_A. |
| 48 | PB14 | bidirectional | 5 V-tolerant Fm+-capable I/O with LCD function supplied by VLCD; alternate functions include TIM1_CH2N, I2C3_SDA, SPI2_MISO, TSC_G1_IO3, LCD_SEG14 and SAI1_MCLK_A. |
| 49 | PB15 | bidirectional | 5 V-tolerant I/O with LCD function supplied by VLCD; alternate functions include RTC_REFIN, TIM1_CH3N, SPI2_MOSI, TSC_G1_IO4, LCD_SEG15 and SAI1_SD_A. |
| 50 | PC6 | bidirectional | 5 V-tolerant I/O with LCD function supplied by VLCD; alternate functions include TSC_G4_IO1 and LCD_SEG24. |
| 51 | PA10 | bidirectional | 5 V-tolerant Fm+-capable I/O with LCD function supplied by VLCD; alternate functions include TIM1_CH3, SAI1_PDM_DI1, I2C1_SDA, USART1_RX, USB_CRS_SYNC, LCD_COM2, SAI1_SD_A and TIM17_BKIN. |
| 52 | PA11 | bidirectional | 5 V-tolerant I/O with USB function supplied by VDDA-independent VDDUSB when USB alternate function is selected; alternate functions include TIM1_CH4, TIM1_BKIN2, SPI1_MISO, USART1_CTS and USB_DM. |
| 53 | PA12 | bidirectional | 5 V-tolerant I/O with USB function supplied by VDDUSB when USB alternate function is selected; alternate functions include TIM1_ETR, SPI1_MOSI, LPUART1_RX, USART1_RTS_DE and USB_DP. |
| 54 | PA13 | bidirectional | 5 V-tolerant I/O that after reset is configured as JTMS-SWDIO with an internal pull-up enabled; other alternate functions include IR_OUT, USB_NOE and SAI1_SD_B. |
| 55 | VDDUSB | power_in | USB transceiver supply, 3.0 to 3.6 V when USB is used, and connected to VDD when USB is not used. |
| 56 | PA14 | bidirectional | 5 V-tolerant I/O that after reset is configured as JTCK-SWCLK with an internal pull-down enabled; other alternate functions include LPTIM1_OUT, I2C1_SMBA, LCD_SEG5 and SAI1_FS_B. |
| 57 | PA15 | bidirectional | 5 V-tolerant I/O that after reset is configured as JTDI with an internal pull-up enabled; other alternate functions include TIM2_CH1, TIM2_ETR, SPI1_NSS, TSC_G3_IO1, LCD_SEG17 and MCO. |
| 58 | PC10 | bidirectional | 5 V-tolerant I/O with LCD function supplied by VLCD; alternate functions include TRACED1, TSC_G3_IO2 and LCD_COM4/LCD_SEG28/LCD_SEG40. |
| 59 | PC11 | bidirectional | 5 V-tolerant I/O with LCD function supplied by VLCD; alternate functions include TSC_G3_IO3 and LCD_COM5/LCD_SEG29/LCD_SEG41. |
| 60 | PC12 | bidirectional | 5 V-tolerant I/O with LCD function supplied by VLCD; alternate functions include LSCO, TRACED3, TSC_G3_IO4 and LCD_COM6/LCD_SEG30/LCD_SEG42, and additional function RTC_TAMP3/WKUP3. |
| 61 | PD0 | bidirectional | 5 V-tolerant I/O with alternate functions SPI2_NSS and CM4_EVENTOUT. |
| 62 | PD1 | bidirectional | 5 V-tolerant I/O with alternate functions SPI2_SCK and CM4_EVENTOUT. |
| 63 | PB3 | bidirectional | 5 V-tolerant I/O with LCD and analog switch functions that after reset is configured as JTDO-TRACESWO; other alternate functions include TIM2_CH2, SPI1_SCK, USART1_RTS_DE and SAI1_SCK_B, and additional function COMP2_INM. |
| 64 | PB4 | bidirectional | 5 V-tolerant I/O with analog switch function supplied by VDDA that after reset is configured as NJTRST with an internal pull-up enabled; other alternate functions include I2C3_SDA, SPI1_MISO, USART1_CTS and TIM17_BKIN, and additional function COMP2_INP. |
| 65 | PB5 | bidirectional | 5 V-tolerant I/O with LCD function supplied by VLCD; alternate functions include LPTIM1_IN1, I2C1_SMBA, SPI1_MOSI, USART1_CK, LPUART1_TX, LCD_SEG9, COMP2_OUT and TIM16_BKIN. |
| 66 | PB6 | bidirectional | 5 V-tolerant Fm+-capable I/O with LCD and analog switch functions; alternate functions include LPTIM1_ETR, I2C1_SCL, USART1_TX, LCD_SEG6, SAI1_FS_B, TIM16_CH1N and MCO, and additional function COMP2_INP. |
| 67 | PB7 | bidirectional | 5 V-tolerant Fm+-capable I/O with LCD and analog switch functions; alternate functions include LPTIM1_IN2, TIM1_BKIN, I2C1_SDA, USART1_RX, LCD_SEG21 and TIM17_CH1N, and additional functions COMP2_INM and PVD_IN. |
| 68 | VDD | power_in | Supply pin, 1.71 to 3.6 V, that must be wired together with VDDRF and VDDSMPS. |
| 69 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | QFN-68-EP(8x8) |
| Category | RF & Radio |
| Pins | 69 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage | VDDX - VSS | -0.3 | 4 | V | Including VDD, VDDA, VDDUSB, VLCD, VDDRF, VDDSMPS, VBAT, VREF+ | 85 | |
| Input voltage on FT_xxx pins | VIN | -0.3 | V | 85 | |||
| Input voltage on TT_xx pins | VIN | 4 | V | 85 | |||
| Input voltage on any other pin | VIN | 4 | V | 85 | |||
| Variations between different VDDX power pins of the same domain | /ΔVDDx/ | 50 | mV | 85 | |||
| Variations between all the different ground pins | /VSSx-VSS/ | 50 | mV | 85 | |||
| Allowed voltage difference for VREF+ > VDDA | VREF+ - VDDA | 0.4 | V | 85 | |||
| Total current into sum of all VDD power lines (source) | ∑IVDD | 130 | mA | 85 | |||
| Total current out of sum of all VSS ground lines (sink) | ∑IVSS | 130 | mA | 85 | |||
| Maximum current into each VDD power pin (source) | IVDD(PIN) | 100 | mA | 85 | |||
| Maximum current out of each VSS ground pin (sink) | IVSS(PIN) | 100 | mA | 85 | |||
| Output current sunk by any I/O and control pin except FT_f | IIO(PIN) | 20 | mA | 85 | |||
| Output current sunk by any FT_f pin | IIO(PIN) | 20 | mA | 85 | |||
| Output current sourced by any I/O and control pin | IIO(PIN) | 20 | mA | 85 | |||
| Total output current sunk by sum of all I/Os and control pins | ∑IIO(PIN) | 100 | mA | 85 | |||
| Total output current sourced by sum of all I/Os and control pins | ∑IIO(PIN) | 100 | mA | 85 | |||
| Injected current on FT_xxx, TT_xx, RST and B pins, except PB0 and PB1 | IINJ(PIN) | -5 | 0 | mA | 85 | ||
| Injected current on PB0 and PB1 | IINJ(PIN) | -5 | 0 | mA | 85 | ||
| Total injected current (sum of all I/Os and control pins) | ∑/IINJ(PIN)/ | 25 | mA | 85 | |||
| Storage temperature range | TSTG | -65 | 150 | °C | 86 | ||
| Maximum junction temperature | TJ | 130 | °C | 86 | |||
| Internal AHB clock frequency | fHCLK | 0 | 64 | MHz | 87 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 64 | MHz | 87 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 64 | MHz | 87 | ||
| Standard operating voltage | VDD | 1.71 | 3.6 | V | 87 | ||
| Analog supply voltage, ADC or COMP used | VDDA | 1.62 | 3.6 | V | ADC or COMP used | 87 | |
| Analog supply voltage, VREFBUF used | VDDA | 2.4 | V | VREFBUF used | 87 | ||
| Backup operating voltage | VBAT | 1.55 | 3.6 | V | 87 | ||
| SMPS feedback voltage | VFBSMPS | 1.4 | 3.6 | V | 88 | ||
| Minimum RF voltage | VDDRF | 1.71 | 3.6 | V | 88 | ||
| USB supply voltage, USB used | VDDUSB | 3 | 3.6 | V | USB used | 88 | |
| USB supply voltage, USB not used | VDDUSB | 0 | 3.6 | V | USB not used | 88 | |
| I/O input voltage, TT_xx | VIN | -0.3 | V | 88 | |||
| I/O input voltage, all I/O except TT_xx | VIN | -0.3 | V | 88 | |||
| Power dissipation, VFQFPN68 | PD | 425 | mW | TA = 85 °C for suffix 6 or TA = 105 °C for suffix 7 | 88 | ||
| Ambient temperature for the suffix 7 version, maximum power dissipation | TA | -40 | 105 | °C | Maximum power dissipation | 88 | |
| Ambient temperature for the suffix 7 version, low-power dissipation | TA | 125 | °C | Low-power dissipation | 88 | ||
| Junction temperature range, suffix 7 version | TJ | -40 | 125 | °C | Suffix 7 version | 88 | |
| Frequency operating range (BLE) | Fop | 2402 | 2480 | MHz | 88 | ||
| Frequency operating range (802.15.4) | Fop | 2405 | 2480 | MHz | 93 | ||
| Frequency drift (BLE 1 Mbps) | fd | -50 | 50 | kHz | Bluetooth Low Energy: ±50 kHz | 89 | |
| Maximum drift rate (BLE 1 Mbps) | maxdr | -20 | 20 | kHz/50 µs | Bluetooth Low Energy: ±20 kHz / 50 µs | 89 | |
| Frequency offset (BLE 1 Mbps) | fo | -150 | 150 | kHz | Bluetooth Low Energy: ±150 kHz | 89 | |
| Frequency deviation average (BLE 1 Mbps) | ∆f1 | 225 | 275 | kHz | Bluetooth Low Energy: between 225 and 275 kHz | 89 | |
| Frequency deviation ratio ∆f2 (average) / ∆f1 (average) (BLE 1 Mbps) | ∆f2/∆f1 | 0.8 | Bluetooth Low Energy: > 0.80 | 89 | |||
| VDD fall time rate | tVDD | 10 | µs/V | VDD fall time rate | 96 | ||
| Reset temporization after BOR0 is detected | tRSTTEMPO | 250 | 400 | µs | VDD rising | 96 | |
| Brown-out reset threshold 0, rising edge | VBOR0 | 1.62 | 1.66 | 1.7 | V | Rising edge | 96 |
| Brown-out reset threshold 0, falling edge | VBOR0 | 1.6 | 1.64 | 1.69 | V | Falling edge | 96 |
| Internal reference voltage | VREFINT | 1.182 | 1.212 | 1.232 | V | -40 °C < TA < +125 °C | 98 |
| Internal reference voltage spread over the temperature range | ∆VREFINT | 5 | 7.5 | mV | VDD = 3 V | 98 | |
| Temperature coefficient | TCoeff | 30 | 50 | ppm/°C | -40 °C < TA < +125 °C | 98 | |
| Voltage coefficient | VDDCoeff | 250 | 1200 | ppm/V | 3.0 V < VDD < 3.6 V | 98 | |
| 1/4 reference voltage | VREFINT_DIV1 | 24 | 25 | 26 | % | 98 | |
| 1/2 reference voltage | VREFINT_DIV2 | 49 | 50 | 51 | % | 98 | |
| 3/4 reference voltage | VREFINT_DIV3 | 74 | 75 | 76 | % | 98 | |
| Start time of reference voltage buffer when ADC is enabled | tstart_vrefint | 8 | 12 | µs | 98 | ||
| Supply current in Run mode, range 1, 64 MHz | IDD(Run) | 8.15 | 9.3 | mA | Range 1, fHCLK = 64 MHz, all peripherals disabled, 25 °C | 100 | |
| Supply current in Stop 2 mode, RTC disabled, LCD disabled, BLE disabled | IDD(Stop 2) | 52 | 135.6 | µA | VDD = 3.0 V, 105 °C | 105 | |
| Supply current in Stop 1 mode, RTC disabled, BLE disabled, LCD disabled | IDD(Stop 1) | 215 | 746 | µA | VDD = 3.0 V, 105 °C | 107 |
CAD (KiCad official)
- Symbol:
STM32WB55RGV7 - Footprint:
Package_DFN_QFN:QFN-68-1EP_8x8mm_P0.4mm_EP5.2x5.2mm - 3D model: QFN-68-EP(8x8) (KiCad packages3D, STEP)
- 3D model files:
stm32wb55rgv7-etched.step/stm32wb55rgv7-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32wb55rgv7.step/stm32wb55rgv7.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (193 pp, sha256
dfe954666bc00fe6, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).