10 pF Capacitor 0402 - Walsin MT15N100J500CT

Walsin Technology Corporation MT15N100J500CT: 0402 Automotive MLCC, 10 pF ±5% NP0, 50 V. An Adom Basic Part: Adom keeps it on reels for its pick-and-place line, so boards built with it draw on Adom stock.

Key specs

Notes for designers

MT15N100J500CT is the one automotive-grade part in Adom's Walsin MLCC set: a 0402 NP0 (C0G) capacitor, 10 pF ±5%, rated 50 VDC, from the MT series, Walsin's AEC-Q200-qualified line. (p.1, p.2) The decode follows the MT ordering table (15 = 0402, N = NP0, 100 = 10 pF, J = ±5%, 500 = 50 VDC) and the product sits in the NP0 range grid at 0402 / 50 V. (p.2, p.6)

Electrically it behaves like any good C0G: ±30 ppm/°C from −55 to +125 °C, (p.3) Q ≥ 400+20C below 30 pF, so ≥600 here, at 1 MHz, (p.3, p.14) and insulation resistance of 10 GΩ or R×C ≥ 500 Ω·F. (p.14) What the MT prefix buys is the qualification record: 1,000 h operational life at 125 °C and 200% of rated voltage, 1,000 h unpowered storage at 150 °C, and 1,000 thermal cycles, all run to the AEC-Q200 test list. (p.14, p.15, p.18)

Mechanically it is a standard 1.00 × 0.50 × 0.50 mm 0402, reflow-only, (p.3) shipped 10,000 to a 7-inch paper-tape reel at MSL 1. (p.13, p.28)

Footprint

The datasheet has no land pattern, so the pads are the IPC-7351 nominal pattern (KiCad's standard Capacitor_SMD:C_0402_1005Metric), replacing pads that were off it by up to 0.12 mm.

Source: IPC-7351 nominal (no land pattern in the datasheet): KiCad 10 Capacitor_SMD:C_0402_1005Metric pads.

Corners: KiCad roundrects with the radius held to 0.25 x the smaller pad side and no more than 0.1 mm (IPC-7351C favours rounded corners for paste release); copper area within 2.47 % of a square-cornered pad.

Chip outline

The part's 3D outline in the standard pose (pad 1 toward the viewer), drawn from the STEP by Adom's OpenCascade service; the part number sits where the laser-etched mark is on the 3D model and reads the same way.

Symbol options

The default symbol, MT15N100J500CT.kicad_sym (the one in the Symbol & Footprint panel), is the plain standard symbol. MT15N100J500CT-outline.kicad_sym is the same symbol with the part's 3D chip outline drawn beside it, its part number placed and reading as on the 3D model.

Ordering

Downloads

Provenance

• Datasheet: MULTILAYER CERAMIC CAPACITORS Automotive Capacitors Series (MT), Qualified to AEC-Q200, 0201 to 1210 Sizes (10V to 1000V), X8G, NP0 & X7R Dielectrics - Approval Sheet, ASC_ Automotive Cap_(MT) revised Apr. 2026, Walsin Technology Corporation (Passive System Alliance). md5 54d9c4a99bc5eab01edf024e8331cd94
• Footprint: IPC-7351 nominal (no land pattern in the datasheet): KiCad 10 Capacitor_SMD:C_0402_1005Metric pads. Pads set to the IPC-7351 nominal pattern on 2026-10-03.
• 3D model and symbol: unchanged by the footprint pass; the etched STEP adds a flat virtual part-number mark (an identification aid, not the maker's marking).

More

• Datasheet pages: the 29 datasheet pages as images.
• Assembly animation: the part dropping onto its pads, and Adom's pick-and-place picking it from tape.