3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownNCP1076ABP100G
onsemi · AC-DC Controllers & Regulators · DIP-7
NCP1076ABP100G from onsemi, in a DIP-7. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VCC | power_in | IC supply pin connected to an external capacitor, with VCC management that includes auto-recovery over-voltage protection. |
| 2 | BO/AC_OVP | input | Detects low input voltage (brown-out) and too high an input voltage (Ac line OVP); must not be left floating and should be connected directly to GND if unused. |
| 3 | GND | power_in | IC ground. |
| 4 | FB | input | Feedback signal input; an opto-coupler connected here adjusts the peak current set-point according to the output power demand. |
| 5 | DRAIN | passive | Internal 700 V power MOSFET drain connection. |
| 7 | GND | power_in | IC ground. |
| 8 | GND | power_in | IC ground. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | DIP-7 |
| Category | Power Management ICs |
| Pins | 7 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC increasing level at which the switcher starts operation | VCC(ON) | 8 | 8.4 | 8.9 | V | 6 | |
| VCC decreasing level at which the HV current source restarts | VCC(MIN) | 6.5 | 6.9 | 7.3 | V | 6 | |
| VCC decreasing level at which the switcher stops operation (UVLO) | VCC(OFF) | 6.1 | 6.5 | 6.9 | V | 6 | |
| Power switch on-state resistance, TJ = 25°C | RDS(ON) | 4.8 | 6.8 | Ω | IDRAIN = 50 mA, TJ = 25°C, NCP1076uz/77uz | 6 | |
| Power switch on-state resistance, TJ = 125°C | RDS(ON) | 9.3 | 11.6 | Ω | IDRAIN = 50 mA, TJ = 125°C, NCP1076uz/77uz | 6 | |
| Power switch & start-up breakdown voltage | BVDSS | 700 | V | IDRAIN(OFF) = 120 µA, TJ = 25°C | 6 | ||
| High-voltage current source Istart1 | Istart1 | 4 | 9 | 12 | mA | VCC = VCC(ON), 200 mV | 6 |
| Maximum internal current set-point at beginning of switching cycle | IPK(0) | 690 | 765 | 840 | mA | FB pin open, BO/AC_OVP pin voltage ≈ 0.8 V, TJ = 25°C, NCP1076uz | 6 |
| Oscillation frequency, 100 kHz version | fOSC(100) | 90 | 100 | 110 | kHz | TJ = 25°C (Note 4) | 7 |
| Maximum duty-cycle | DMAX | 64 | 68 | 72 | % | 7 | |
| Frequency below which skip-cycle occurs | fMIN | 23 | 27 | 31 | kHz | TJ = 25°C (Note 4) | 8 |
| VCC voltage at which the switcher stops pulsing | VOVP | 17 | 18 | 18.8 | V | 8 | |
| Brown-out level, switcher starts pulsing | VBO(ON) | 0.76 | 0.8 | 0.84 | V | 8 | |
| OVP level when the switcher stops pulsing | VACOVP(ON) | 2.755 | 2.9 | 3.045 | V | 8 | |
| OVP level when the switcher starts pulsing | VACOVP(OFF) | 2.3 | 2.6 | 2.9 | V | 8 | |
| Drain pin voltage above which MOSFET operates | VHV(EN) | 72 | 91 | 110 | V | Checked after TSD, UVLO, SCP, or VCC OVP mode, BO/AC_OVP pin = 0 V | 8 |
| Fault validation further to error flag assertion | tSCP | 35 | 48 | ms | 8 | ||
| Internal IC consumption, MOSFET switching | ICC1 | 1.26 | mA | fSW = 65 kHz, NCP1076uz/77uz | 6 | ||
| Internal IC consumption, no switching | ICC(skip) | 400 | µA | VFB is 0 V | 6 | ||
| Maximum internal current set-point at 50% duty-cycle | IPK | 650 | mA | FB pin open, TJ = 25°C, NCP1076uz | 6 | ||
| Final switch current, fSW = 100 kHz | IPKSW(100) | 685 | mA | primary slope 200 mA/µs, fSW = 100 kHz, NCP1076uz | 7 | ||
| Temperature shutdown | TSD | 150 | °C | Guaranteed by design | 8 | ||
| Power supply voltage, VCC pin, continuous | VCC | -0.3 | 20 | V | 5 | ||
| Voltage on all pins, except DRAIN and VCC | Vinmax | -0.3 | 10 | V | 5 | ||
| DRAIN voltage | BVDSS | -0.3 | 700 | V | 5 | ||
| Maximum current into VCC pin | ICC | 15 | mA | 5 | |||
| Drain current peak during transformer saturation, TJ = 150°C | IDS(PK) | 2.2 | A | TJ = 150°C, NCP1076uz/77uz | 5 | ||
| Drain current peak during transformer saturation, TJ = 25°C | IDS(PK) | 3.9 | A | TJ = 25°C, NCP1076uz/77uz | 5 | ||
| Maximum junction temperature | TJMAX | 150 | °C | 5 | |||
| Storage temperature range | -60 | 150 | °C | 5 | |||
| ESD HBM (all pins except HV pin) | HBM | 2 | kV | JEDEC JESD22-A114F | 5 | ||
| ESD HBM (Drain pin) | HBM | 1 | kV | JEDEC JESD22-A114F | 5 | ||
| ESD CDM | CDM | 1 | kV | JEDEC JESD22-C101E | 5 | ||
| ESD Machine Model | MM | 200 | V | JEDEC JESD22-A115-A | 5 | ||
| Thermal resistance junction-to-air, PDIP7 | RθJ-A | 77 | °C/W | 0.36 Sq. Inch | 5 | ||
| Thermal resistance junction-to-air, PDIP7 | RθJ-A | 68 | °C/W | 1.0 Sq. Inch | 5 |
CAD (KiCad official)
- Symbol:
NCP1076ABP100G - Footprint:
Package_DIP:DIP-8-N6_W7.62mm - 3D model: DIP-7, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 5.33 mm tall, datasheet A, max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
ncp1076abp100g-etched.step/ncp1076abp100g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncp1076abp100g.step/ncp1076abp100g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (34 pp, sha256
29f24cb516736081, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).