3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownIGCM10F60GA
Infineon Technologies · Brushless DC (BLDC) Motor Driver · DIP-24
IGCM10F60GA from Infineon Technologies, in a DIP-24. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VS(U) | power_in | U-phase high-side floating IC supply offset voltage; the high-side circuit floats with respect to VSS and tolerates transient negative voltage of -50 V versus VSS. |
| 2 | VB(U) | power_in | U-phase high-side floating IC supply voltage (VB to VS); the UVLO thresholds are typically 12.1 V rising and 10.4 V falling. |
| 3 | VS(V) | power_in | V-phase high-side floating IC supply offset voltage; the high-side circuit floats with respect to VSS and tolerates transient negative voltage of -50 V versus VSS. |
| 4 | VB(V) | power_in | V-phase high-side floating IC supply voltage (VB to VS); the UVLO thresholds are typically 12.1 V rising and 10.4 V falling. |
| 5 | VS(W) | power_in | W-phase high-side floating IC supply offset voltage; the high-side circuit floats with respect to VSS and tolerates transient negative voltage of -50 V versus VSS. |
| 6 | VB(W) | power_in | W-phase high-side floating IC supply voltage (VB to VS); the UVLO thresholds are typically 12.1 V rising and 10.4 V falling. |
| 7 | HIN(U) | input | U-phase high-side gate driver input, positive logic with Schmitt-trigger thresholds compatible with 3.3 V controller outputs and an internal pull-down of about 5 kΩ. |
| 8 | HIN(V) | input | V-phase high-side gate driver input, positive logic with Schmitt-trigger thresholds compatible with 3.3 V controller outputs and an internal pull-down of about 5 kΩ. |
| 9 | HIN(W) | input | W-phase high-side gate driver input, positive logic with Schmitt-trigger thresholds compatible with 3.3 V controller outputs and an internal pull-down of about 5 kΩ. |
| 10 | LIN(U) | input | U-phase low-side gate driver input, positive logic with Schmitt-trigger thresholds compatible with 3.3 V controller outputs and an internal pull-down of about 5 kΩ. |
| 11 | LIN(V) | input | V-phase low-side gate driver input, positive logic with Schmitt-trigger thresholds compatible with 3.3 V controller outputs and an internal pull-down of about 5 kΩ. |
| 12 | LIN(W) | input | W-phase low-side gate driver input, positive logic with Schmitt-trigger thresholds compatible with 3.3 V controller outputs and an internal pull-down of about 5 kΩ. |
| 13 | VDD | power_in | Low-side control supply providing power to input logic and output stage; recommended operating range 14.0 V to 18.5 V with 16.0 V typical, absolute maximum -1 to 20 V. |
| 14 | VFO | output | Fault output and NTC temperature monitor; open-drain fault output indicating UV at VDD or ITRIP overcurrent, requiring an external pull-up resistor to 5 V or 3.3 V. |
| 15 | ITRIP | input | Overcurrent shutdown input referenced to VSS with comparator threshold typically 0.47 V (400 to 540 mV) and absolute input voltage range -1 to 10 V. |
| 16 | VSS | power_in | Low-side control negative supply and logic reference ground, to which the NTC and input logic are referenced. |
| 17 | NW | passive | W-phase low-side emitter available for phase current measurement; the connection to VSS should be kept as short as possible. |
| 18 | NV | passive | V-phase low-side emitter available for phase current measurement; the connection to VSS should be kept as short as possible. |
| 19 | NU | passive | U-phase low-side emitter available for phase current measurement; the connection to VSS should be kept as short as possible. |
| 20 | W | output | Motor W-phase output connected to the high-side emitter and low-side collector of the W-phase IGBTs. |
| 21 | V | power_in | Motor V-phase output connected to the high-side emitter and low-side collector of the V-phase IGBTs. |
| 22 | U | output | Motor U-phase output connected to the high-side emitter and low-side collector of the U-phase IGBTs. |
| 23 | P | power_in | Positive bus input voltage to the high-side IGBTs; the bus voltage must not exceed 450 V. |
| 24 | NC | unconnected | No connection. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Infineon Technologies |
| Package | DIP-24 |
| Category | Motor Driver ICs |
| Pins | 24 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage temperature range | TSTG | -40 | 125 | °C | 8 | ||
| Operating case temperature | TC | -40 | 125 | °C | Refer to Figure 7 | 8 | |
| Operating junction temperature | TJ | -40 | 150 | °C | 8 | ||
| Isolation test voltage | VISO | 2000 | V | 1 min, RMS, f = 60 Hz | 8 | ||
| Max. blocking voltage | VCES | 600 | V | 8 | |||
| DC link supply voltage of P-N | VPN | 450 | V | Applied between P-N | 8 | ||
| DC link supply voltage (surge) of P-N | VPN(surge) | 500 | V | Applied between P-N | 8 | ||
| Output current | IC | -10 | 10 | A | TC = 25°C, TJ < 150°C | 8 | |
| Output current | IC | -6 | 6 | A | TC = 100°C, TJ < 150°C | 8 | |
| Maximum peak collector current | IC(peak) | -20 | 20 | A | TC = 25°C, TJ < 150°C, less than 1 ms | 8 | |
| Power dissipation per IGBT | Ptot | 26.1 | W | 8 | |||
| Short circuit withstand time | tSC | 5 | µs | VDC ≤ 400 V, TJ = 150°C | 8 | ||
| High-side offset voltage | VS | 600 | V | 8 | |||
| Repetitive peak reverse voltage of bootstrap diode | VRRM | 600 | V | 8 | |||
| Module supply voltage | VDD | -1 | 20 | V | 8 | ||
| High-side floating supply voltage (VB reference to VS) | VBS | -1 | 20 | V | 8 | ||
| Input voltage (LIN, HIN, ITRIP) | VIN | -1 | 10 | V | 8 | ||
| Single IGBT thermal resistance, junction to case | RthJC | 4.79 | K/W | See Figure 7 for TC measurement point | 9 | ||
| DC link supply voltage of P-N | VPN | 0 | 400 | V | 10 | ||
| Low-side supply voltage | VDD | 14 | 16 | 18.5 | V | 10 | |
| High-side floating supply voltage (VB vs. VS) | VBS | 13.5 | 18.5 | V | 10 | ||
| Logic input voltages LIN, HIN, ITRIP | VIN | 0 | 5 | V | 10 | ||
| Inverter PWM carrier frequency | fPWM | 20 | kHz | 10 | |||
| External deadtime between HIN and LIN | DT | 1 | µs | 10 | |||
| Voltage between VSS, N (including surge) | VCOMP | -5 | 5 | V | 10 | ||
| Minimum input pulse width | PWIN(ON) | 1 | µs | 10 | |||
| Control supply variation | ΔVBS | -1 | 1 | V/µs | 10 | ||
| Collector-emitter voltage | VCE(Sat) | 1.6 | 2 | V | IC = 6 A, TJ = 25°C | 11 | |
| Collector-emitter voltage | VCE(Sat) | 1.8 | V | IC = 6 A, TJ = 150°C | 11 | ||
| Collector-emitter leakage current | ICES | 1 | mA | VCE = 600 V | 11 | ||
| Diode forward voltage | VF | 1.75 | 2.2 | V | IF= 6 A, TJ = 25°C | 11 | |
| Diode forward voltage | VF | 1.8 | V | IF= 6 A, TJ = 150°C | 11 | ||
| Logic "1" input voltage (LIN, HIN) | VIH | 2.1 | 2.5 | V | 11 | ||
| Logic "0" input voltage (LIN, HIN) | VIL | 0.7 | 0.9 | V | 11 | ||
| ITRIP positive going threshold | VIT,TH+ | 400 | 470 | 540 | mV | 11 | |
| ITRIP input hysteresis | VIT,HYS | 40 | 70 | mV | 11 | ||
| VDD supply undervoltage positive going threshold | VDDUV+ | 10.8 | 12.1 | 13 | V | 11 | |
| VBS supply undervoltage positive going threshold | VBSUV+ | 10.8 | 12.1 | 13 | V | 11 | |
| VDD supply undervoltage negative going threshold | VDDUV- | 9.5 | 10.4 | 11.2 | V | 11 | |
| VBS supply undervoltage negative going threshold | VBSUV- | 9.5 | 10.4 | 11.2 | V | 11 | |
| VDD supply undervoltage lockout hysteresis | VDDUVH | 1 | 1.7 | V | 11 | ||
| VBS supply undervoltage lockout hysteresis | VBSUVH | 1 | 1.7 | V | 11 | ||
| Quiescent VBx supply current (VBx only) | IQBS | 300 | 500 | µA | HIN = 0 V | 11 | |
| Quiescent VDD supply current (VDD only) | IQDD | 370 | 900 | µA | LIN = 0 V, HINX = 5 V | 11 | |
| Input bias current for LIN, HIN | IIN+ | 1 | 1.5 | mA | VIN = 5 V | 11 | |
| Input bias current for ITRIP | IITRIP+ | 65 | 150 | µA | VITRIP = 5 V | 11 | |
| Fault clear time after ITRIP-fault | tFLTCLR | 40 | 65 | 200 | µs | 12 | |
| ITRIP to fault propagation delay | tFLT | 680 | 1000 | ns | VLIN, HIN = 0 or VLIN, HIN = 5 V, VITRIP = 1 V | 12 | |
| Comparative tracking index (CTI) | 550 | V | 14 | ||||
| Mounting torque M3 screw and washer | 0.59 | 0.69 | 0.78 | Nm | M3 screw and washer | 14 | |
| Backside curvature | -50 | 100 | µm | Refer to Figure 8 | 14 | ||
| Resistance | RNTC | 85 | kΩ | TNTC = 25°C | 13 | ||
| B-constant of NTC thermistor | B(25/100) | 4092 | K | 13 | |||
| Input filter time ITRIP | tITRIP | 530 | ns | VITRIP = 1 V | 12 | ||
| Input filter time at LIN, HIN for turn on and off | tFIL,IN | 290 | ns | VLIN, HIN = 0 V or 5 V | 12 | ||
| Internal deadtime | DTIC | 380 | ns | 12 | |||
| Bootstrap diode forward voltage | VF_BSD | 2.6 | V | IF = 20 mA | 11 | ||
| Input bias current for LIN, HIN | IIN- | 2 | mA | VIN = 0 V | 11 |
CAD (KiCad official)
- Symbol:
IGCM10F60GA - Footprint:
Package_DIP:DIP-24_W7.62mm - 3D model: DIP-24 (KiCad packages3D, STEP)
- 3D model files:
igcm10f60ga-etched.step/igcm10f60ga-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);igcm10f60ga.step/igcm10f60ga.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Infineon Technologies datasheet (22 pp, sha256
279fc8deac0bbaf2, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).