Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

IGCM10F60GA

Infineon Technologies · Brushless DC (BLDC) Motor Driver · DIP-24

IGCM10F60GA from Infineon Technologies, in a DIP-24. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VS(U) power_in U-phase high-side floating IC supply offset voltage; the high-side circuit floats with respect to VSS and tolerates transient negative voltage of -50 V versus VSS.
2 VB(U) power_in U-phase high-side floating IC supply voltage (VB to VS); the UVLO thresholds are typically 12.1 V rising and 10.4 V falling.
3 VS(V) power_in V-phase high-side floating IC supply offset voltage; the high-side circuit floats with respect to VSS and tolerates transient negative voltage of -50 V versus VSS.
4 VB(V) power_in V-phase high-side floating IC supply voltage (VB to VS); the UVLO thresholds are typically 12.1 V rising and 10.4 V falling.
5 VS(W) power_in W-phase high-side floating IC supply offset voltage; the high-side circuit floats with respect to VSS and tolerates transient negative voltage of -50 V versus VSS.
6 VB(W) power_in W-phase high-side floating IC supply voltage (VB to VS); the UVLO thresholds are typically 12.1 V rising and 10.4 V falling.
7 HIN(U) input U-phase high-side gate driver input, positive logic with Schmitt-trigger thresholds compatible with 3.3 V controller outputs and an internal pull-down of about 5 kΩ.
8 HIN(V) input V-phase high-side gate driver input, positive logic with Schmitt-trigger thresholds compatible with 3.3 V controller outputs and an internal pull-down of about 5 kΩ.
9 HIN(W) input W-phase high-side gate driver input, positive logic with Schmitt-trigger thresholds compatible with 3.3 V controller outputs and an internal pull-down of about 5 kΩ.
10 LIN(U) input U-phase low-side gate driver input, positive logic with Schmitt-trigger thresholds compatible with 3.3 V controller outputs and an internal pull-down of about 5 kΩ.
11 LIN(V) input V-phase low-side gate driver input, positive logic with Schmitt-trigger thresholds compatible with 3.3 V controller outputs and an internal pull-down of about 5 kΩ.
12 LIN(W) input W-phase low-side gate driver input, positive logic with Schmitt-trigger thresholds compatible with 3.3 V controller outputs and an internal pull-down of about 5 kΩ.
13 VDD power_in Low-side control supply providing power to input logic and output stage; recommended operating range 14.0 V to 18.5 V with 16.0 V typical, absolute maximum -1 to 20 V.
14 VFO output Fault output and NTC temperature monitor; open-drain fault output indicating UV at VDD or ITRIP overcurrent, requiring an external pull-up resistor to 5 V or 3.3 V.
15 ITRIP input Overcurrent shutdown input referenced to VSS with comparator threshold typically 0.47 V (400 to 540 mV) and absolute input voltage range -1 to 10 V.
16 VSS power_in Low-side control negative supply and logic reference ground, to which the NTC and input logic are referenced.
17 NW passive W-phase low-side emitter available for phase current measurement; the connection to VSS should be kept as short as possible.
18 NV passive V-phase low-side emitter available for phase current measurement; the connection to VSS should be kept as short as possible.
19 NU passive U-phase low-side emitter available for phase current measurement; the connection to VSS should be kept as short as possible.
20 W output Motor W-phase output connected to the high-side emitter and low-side collector of the W-phase IGBTs.
21 V power_in Motor V-phase output connected to the high-side emitter and low-side collector of the V-phase IGBTs.
22 U output Motor U-phase output connected to the high-side emitter and low-side collector of the U-phase IGBTs.
23 P power_in Positive bus input voltage to the high-side IGBTs; the bus voltage must not exceed 450 V.
24 NC unconnected No connection.

Key specifications

Parameter Value
Manufacturer Infineon Technologies
Package DIP-24
Category Motor Driver ICs
Pins 24

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Storage temperature range TSTG -40 125 °C 8
Operating case temperature TC -40 125 °C Refer to Figure 7 8
Operating junction temperature TJ -40 150 °C 8
Isolation test voltage VISO 2000 V 1 min, RMS, f = 60 Hz 8
Max. blocking voltage VCES 600 V 8
DC link supply voltage of P-N VPN 450 V Applied between P-N 8
DC link supply voltage (surge) of P-N VPN(surge) 500 V Applied between P-N 8
Output current IC -10 10 A TC = 25°C, TJ < 150°C 8
Output current IC -6 6 A TC = 100°C, TJ < 150°C 8
Maximum peak collector current IC(peak) -20 20 A TC = 25°C, TJ < 150°C, less than 1 ms 8
Power dissipation per IGBT Ptot 26.1 W 8
Short circuit withstand time tSC 5 µs VDC ≤ 400 V, TJ = 150°C 8
High-side offset voltage VS 600 V 8
Repetitive peak reverse voltage of bootstrap diode VRRM 600 V 8
Module supply voltage VDD -1 20 V 8
High-side floating supply voltage (VB reference to VS) VBS -1 20 V 8
Input voltage (LIN, HIN, ITRIP) VIN -1 10 V 8
Single IGBT thermal resistance, junction to case RthJC 4.79 K/W See Figure 7 for TC measurement point 9
DC link supply voltage of P-N VPN 0 400 V 10
Low-side supply voltage VDD 14 16 18.5 V 10
High-side floating supply voltage (VB vs. VS) VBS 13.5 18.5 V 10
Logic input voltages LIN, HIN, ITRIP VIN 0 5 V 10
Inverter PWM carrier frequency fPWM 20 kHz 10
External deadtime between HIN and LIN DT 1 µs 10
Voltage between VSS, N (including surge) VCOMP -5 5 V 10
Minimum input pulse width PWIN(ON) 1 µs 10
Control supply variation ΔVBS -1 1 V/µs 10
Collector-emitter voltage VCE(Sat) 1.6 2 V IC = 6 A, TJ = 25°C 11
Collector-emitter voltage VCE(Sat) 1.8 V IC = 6 A, TJ = 150°C 11
Collector-emitter leakage current ICES 1 mA VCE = 600 V 11
Diode forward voltage VF 1.75 2.2 V IF= 6 A, TJ = 25°C 11
Diode forward voltage VF 1.8 V IF= 6 A, TJ = 150°C 11
Logic "1" input voltage (LIN, HIN) VIH 2.1 2.5 V 11
Logic "0" input voltage (LIN, HIN) VIL 0.7 0.9 V 11
ITRIP positive going threshold VIT,TH+ 400 470 540 mV 11
ITRIP input hysteresis VIT,HYS 40 70 mV 11
VDD supply undervoltage positive going threshold VDDUV+ 10.8 12.1 13 V 11
VBS supply undervoltage positive going threshold VBSUV+ 10.8 12.1 13 V 11
VDD supply undervoltage negative going threshold VDDUV- 9.5 10.4 11.2 V 11
VBS supply undervoltage negative going threshold VBSUV- 9.5 10.4 11.2 V 11
VDD supply undervoltage lockout hysteresis VDDUVH 1 1.7 V 11
VBS supply undervoltage lockout hysteresis VBSUVH 1 1.7 V 11
Quiescent VBx supply current (VBx only) IQBS 300 500 µA HIN = 0 V 11
Quiescent VDD supply current (VDD only) IQDD 370 900 µA LIN = 0 V, HINX = 5 V 11
Input bias current for LIN, HIN IIN+ 1 1.5 mA VIN = 5 V 11
Input bias current for ITRIP IITRIP+ 65 150 µA VITRIP = 5 V 11
Fault clear time after ITRIP-fault tFLTCLR 40 65 200 µs 12
ITRIP to fault propagation delay tFLT 680 1000 ns VLIN, HIN = 0 or VLIN, HIN = 5 V, VITRIP = 1 V 12
Comparative tracking index (CTI) 550 V 14
Mounting torque M3 screw and washer 0.59 0.69 0.78 Nm M3 screw and washer 14
Backside curvature -50 100 µm Refer to Figure 8 14
Resistance RNTC 85 kΩ TNTC = 25°C 13
B-constant of NTC thermistor B(25/100) 4092 K 13
Input filter time ITRIP tITRIP 530 ns VITRIP = 1 V 12
Input filter time at LIN, HIN for turn on and off tFIL,IN 290 ns VLIN, HIN = 0 V or 5 V 12
Internal deadtime DTIC 380 ns 12
Bootstrap diode forward voltage VF_BSD 2.6 V IF = 20 mA 11
Input bias current for LIN, HIN IIN- 2 mA VIN = 0 V 11

CAD (KiCad official)

  • Symbol: IGCM10F60GA
  • Footprint: Package_DIP:DIP-24_W7.62mm
  • 3D model: DIP-24 (KiCad packages3D, STEP)
  • 3D model files: igcm10f60ga-etched.step / igcm10f60ga-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); igcm10f60ga.step / igcm10f60ga.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Infineon Technologies datasheet (22 pp, sha256 279fc8deac0bbaf2, retrieved 2026-11-02, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF