component
STM32F415RGT6TR
Public Made by Adomby adom
STMicroelectronics ST Microelectronics, LQFP-64(10x10). Pinout checked against ST's open pin data, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSTM32F415RGT6TR
STMicroelectronics · ST Microelectronics · LQFP-64(10x10)
STM32F415RGT6TR from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup-domain supply pin for the RTC, backup registers and optional backup SRAM, as stated in the features list. |
| 2 | PC13 | bidirectional | 5 V-tolerant (FT) I/O supplied through the power switch with a 3 mA sink limit, so output speed must not exceed 2 MHz at 30 pF and it must not be used as a current source; additional functions RTC_OUT, RTC_TAMP1, RTC_TS. |
| 3 | PC14/OSC32_IN | bidirectional | FT I/O supplied through the power switch (3 mA limit, output speed up to 2 MHz at 30 pF); in oscillator mode it is the OSC32_IN LSE input and FT tolerance does not apply. |
| 4 | PC15/OSC32_OUT | bidirectional | FT I/O supplied through the power switch (3 mA limit, output speed up to 2 MHz at 30 pF); in oscillator mode it is the OSC32_OUT LSE output and FT tolerance does not apply. |
| 5 | PH0/OSC_IN | bidirectional | I/O with OSC_IN as the HSE oscillator input in oscillator mode, where FT tolerance does not apply; also EVENTOUT. |
| 6 | PH1/OSC_OUT | bidirectional | I/O with OSC_OUT as the HSE oscillator output in oscillator mode, where FT tolerance does not apply; also EVENTOUT. |
| 7 | NRST | bidirectional | Bidirectional active-low reset pin with embedded weak pull-up resistor. |
| 8 | PC0 | bidirectional | 5 V-tolerant (FT) I/O, FT except in analog mode; ADC123_IN10 analog input; alternate OTG_HS_ULPI_STP and EVENTOUT. |
| 9 | PC1 | bidirectional | 5 V-tolerant (FT) I/O, FT except in analog mode; ADC123_IN11 analog input; alternate ETH_MDC and EVENTOUT. |
| 10 | PC2 | bidirectional | 5 V-tolerant (FT) I/O, FT except in analog mode; ADC123_IN12 analog input; alternates SPI2_MISO, I2S2ext_SD, OTG_HS_ULPI_DIR, ETH_MII_TXD2 and EVENTOUT. |
| 11 | PC3 | bidirectional | 5 V-tolerant (FT) I/O, FT except in analog mode; ADC123_IN13 analog input; alternates SPI2_MOSI, I2S2_SD, OTG_HS_ULPI_NXT, ETH_MII_TX_CLK and EVENTOUT. |
| 12 | VSSA | power_in | Analog ground pin for the analog blocks (ADC/DAC). |
| 13 | VDDA | power_in | Analog supply pin for the analog blocks (ADC/DAC) of the device. |
| 14 | PA0/WKUP | bidirectional | 5 V-tolerant (FT) I/O that also serves as the WKUP wake-up input; ADC123_IN0 analog input; alternates USART2_CTS, UART4_TX, ETH_MII_CRS, TIM2_CH1_ETR, TIM5_CH1 and TIM8_ETR. |
| 15 | PA1 | bidirectional | 5 V-tolerant (FT) I/O, FT except in analog mode; ADC123_IN1 analog input; alternates USART2_RTS, UART4_RX, ETH_RMII_REF_CLK, ETH_MII_RX_CLK, TIM5_CH2 and TIM2_CH2. |
| 16 | PA2 | bidirectional | 5 V-tolerant (FT) I/O, FT except in analog mode; ADC123_IN2 analog input; alternates USART2_TX, TIM5_CH3, TIM9_CH1, TIM2_CH3 and ETH_MDIO. |
| 17 | PA3 | bidirectional | 5 V-tolerant (FT) I/O, FT except in analog mode; ADC123_IN3 analog input; alternates USART2_RX, TIM5_CH4, TIM9_CH2, TIM2_CH4, OTG_HS_ULPI_D0 and ETH_MII_COL. |
| 18 | VSS | power_in | Ground pin. |
| 19 | VDD | power_in | Main supply pin for the I/Os and internal regulator; application supply range 1.8 V to 3.6 V. |
| 20 | PA4 | bidirectional | 3.3 V-tolerant (TTa) I/O directly connected to the ADC; ADC12_IN4 and DAC_OUT1 analog functions; alternates SPI1_NSS, SPI3_NSS, USART2_CK, DCMI_HSYNC, OTG_HS_SOF and I2S3_WS. |
| 21 | PA5 | bidirectional | 3.3 V-tolerant (TTa) I/O directly connected to the ADC; ADC12_IN5 and DAC_OUT2 analog functions; alternates SPI1_SCK, OTG_HS_ULPI_CK, TIM2_CH1_ETR and TIM8_CH1N. |
| 22 | PA6 | bidirectional | 5 V-tolerant (FT) I/O, FT except in analog mode; ADC12_IN6 analog input; alternates SPI1_MISO, TIM8_BKIN, TIM13_CH1, DCMI_PIXCLK, TIM3_CH1 and TIM1_BKIN. |
| 23 | PA7 | bidirectional | 5 V-tolerant (FT) I/O, FT except in analog mode; ADC12_IN7 analog input; alternates SPI1_MOSI, TIM8_CH1N, TIM14_CH1, TIM3_CH2, ETH_MII_RX_DV, ETH_RMII_CRS_DV and TIM1_CH1N. |
| 24 | PC4 | bidirectional | 5 V-tolerant (FT) I/O, FT except in analog mode; ADC12_IN14 analog input; alternates ETH_RMII_RX_D0 and ETH_MII_RX_D0. |
| 25 | PC5 | bidirectional | 5 V-tolerant (FT) I/O, FT except in analog mode; ADC12_IN15 analog input; alternates ETH_RMII_RX_D1 and ETH_MII_RX_D1. |
| 26 | PB0 | bidirectional | 5 V-tolerant (FT) I/O, FT except in analog mode; ADC12_IN8 analog input; alternates TIM3_CH3, TIM8_CH2N, OTG_HS_ULPI_D1, ETH_MII_RXD2 and TIM1_CH2N. |
| 27 | PB1 | bidirectional | 5 V-tolerant (FT) I/O, FT except in analog mode; ADC12_IN9 analog input; alternates TIM3_CH4, TIM8_CH3N, OTG_HS_ULPI_D2, ETH_MII_RXD3 and TIM1_CH3N. |
| 28 | PB2/BOOT1 | bidirectional | 5 V-tolerant (FT) I/O with EVENTOUT as its alternate function; the pin name also carries the BOOT1 boot option. |
| 29 | PB10 | bidirectional | 5 V-tolerant (FT) I/O; alternates TIM2_CH3, SPI2_SCK, I2S2_CK, I2C2_SCL, USART3_TX, OTG_HS_ULPI_D3 and ETH_MII_RX_ER. |
| 30 | PB11 | bidirectional | 5 V-tolerant (FT) I/O; alternates TIM2_CH4, I2C2_SDA, USART3_RX, OTG_HS_ULPI_D4, ETH_MII_TX_EN and ETH_RMII_TX_EN. |
| 31 | VCAP_1 | power_in | Regulator decoupling pin; connect the external VCAP_1 capacitor as specified in the datasheet operating conditions. |
| 32 | VDD | power_in | Main supply pin for the I/Os and internal regulator; application supply range 1.8 V to 3.6 V. |
| 33 | PB12 | bidirectional | 5 V-tolerant (FT) I/O; alternates TIM1_BKIN, SPI2_NSS, I2S2_WS, I2C2_SMBA, USART3_CK, CAN2_RX, OTG_HS_ULPI_D5, ETH_MII_TXD0, ETH_RMII_TXD0 and OTG_HS_ID. |
| 34 | PB13 | bidirectional | 5 V-tolerant (FT) I/O; alternates TIM1_CH1N, SPI2_SCK, I2S2_CK, USART3_CTS, CAN2_TX, OTG_HS_ULPI_D6, ETH_MII_TXD1 and ETH_RMII_TXD1; additional function OTG_HS_VBUS. |
| 35 | PB14 | bidirectional | 5 V-tolerant (FT) I/O; alternates TIM1_CH2N, SPI2_MISO, I2S2ext_SD, USART3_RTS, TIM12_CH1, TIM8_CH2N and OTG_HS_DM. |
| 36 | PB15 | bidirectional | 5 V-tolerant (FT) I/O; alternates TIM1_CH3N, SPI2_MOSI, I2S2_SD, TIM8_CH3N, TIM12_CH2 and OTG_HS_DP; additional function RTC_REFIN. |
| 37 | PC6 | bidirectional | 5 V-tolerant (FT) I/O; alternates I2S2_MCK, TIM8_CH1, SDIO_D6, USART6_TX, DCMI_D0 and TIM3_CH1. |
| 38 | PC7 | bidirectional | 5 V-tolerant (FT) I/O; alternates I2S3_MCK, TIM8_CH2, SDIO_D7, USART6_RX, DCMI_D1 and TIM3_CH2. |
| 39 | PC8 | bidirectional | 5 V-tolerant (FT) I/O; alternates TIM8_CH3, SDIO_D0, TIM3_CH3, USART6_CK and DCMI_D2. |
| 40 | PC9 | bidirectional | 5 V-tolerant (FT) I/O; alternates I2S_CKIN, MCO2, TIM8_CH4, SDIO_D1, I2C3_SDA, DCMI_D3 and TIM3_CH4. |
| 41 | PA8 | bidirectional | 5 V-tolerant (FT) I/O; alternates MCO1, USART1_CK, TIM1_CH1, I2C3_SCL and OTG_FS_SOF. |
| 42 | PA9 | bidirectional | 5 V-tolerant (FT) I/O; alternates USART1_TX, TIM1_CH2, I2C3_SMBA and DCMI_D0; additional function OTG_FS_VBUS. |
| 43 | PA10 | bidirectional | 5 V-tolerant (FT) I/O; alternates USART1_RX, TIM1_CH3, OTG_FS_ID and DCMI_D1. |
| 44 | PA11 | bidirectional | 5 V-tolerant (FT) I/O; alternates USART1_CTS, CAN1_RX, TIM1_CH4 and OTG_FS_DM. |
| 45 | PA12 | bidirectional | 5 V-tolerant (FT) I/O; alternates USART1_RTS, CAN1_TX, TIM1_ETR and OTG_FS_DP. |
| 46 | PA13/JTMS-SWDIO | bidirectional | 5 V-tolerant (FT) I/O whose function after reset is JTMS-SWDIO (serial wire debug data), with EVENTOUT. |
| 47 | VCAP_2 | power_in | Regulator decoupling pin; connect the external VCAP_2 capacitor as specified in the datasheet operating conditions. |
| 48 | VDD | power_in | Main supply pin for the I/Os and internal regulator; application supply range 1.8 V to 3.6 V. |
| 49 | PA14/JTCK-SWCLK | bidirectional | 5 V-tolerant (FT) I/O whose function after reset is JTCK-SWCLK (serial wire debug clock), with EVENTOUT. |
| 50 | PA15/JTDI | bidirectional | 5 V-tolerant (FT) I/O whose function after reset is JTDI; alternates TIM2_CH1_ETR, SPI1_NSS, SPI3_NSS and I2S3_WS. |
| 51 | PC10 | bidirectional | 5 V-tolerant (FT) I/O; alternates SPI3_SCK, I2S3_CK, UART4_TX, SDIO_D2, DCMI_D8 and USART3_TX. |
| 52 | PC11 | bidirectional | 5 V-tolerant (FT) I/O; alternates UART4_RX, SPI3_MISO, SDIO_D3, DCMI_D4, USART3_RX and I2S3ext_SD. |
| 53 | PC12 | bidirectional | 5 V-tolerant (FT) I/O; alternates UART5_TX, SDIO_CK, DCMI_D9, SPI3_MOSI, I2S3_SD and USART3_CK. |
| 54 | PD2 | bidirectional | 5 V-tolerant (FT) I/O; alternates TIM3_ETR, UART5_RX, SDIO_CMD and DCMI_D11. |
| 55 | PB3/JTDO/TRACESWO | bidirectional | 5 V-tolerant (FT) I/O whose function after reset is JTDO/TRACESWO; alternates SPI3_SCK, I2S3_CK, TIM2_CH2 and SPI1_SCK. |
| 56 | PB4/NJTRST | bidirectional | 5 V-tolerant (FT) I/O whose function after reset is NJTRST; alternates SPI3_MISO, TIM3_CH1, SPI1_MISO and I2S3ext_SD. |
| 57 | PB5 | bidirectional | 5 V-tolerant (FT) I/O; alternates I2C1_SMBA, CAN2_RX, OTG_HS_ULPI_D7, ETH_PPS_OUT, TIM3_CH2, SPI1_MOSI, SPI3_MOSI, DCMI_D10 and I2S3_SD. |
| 58 | PB6 | bidirectional | 5 V-tolerant (FT) I/O; alternates I2C1_SCL, TIM4_CH1, CAN2_TX, DCMI_D5 and USART1_TX. |
| 59 | PB7 | bidirectional | 5 V-tolerant (FT) I/O; alternates I2C1_SDA, FSMC_NL, DCMI_VSYNC, USART1_RX and TIM4_CH2. |
| 60 | BOOT0 | input | Dedicated BOOT0 boot-selection input; additional function VPP. |
| 61 | PB8 | bidirectional | 5 V-tolerant (FT) I/O; alternates TIM4_CH3, SDIO_D4, TIM10_CH1, DCMI_D6, ETH_MII_TXD3, I2C1_SCL and CAN1_RX. |
| 62 | PB9 | bidirectional | 5 V-tolerant (FT) I/O; alternates SPI2_NSS, I2S2_WS, TIM4_CH4, TIM11_CH1, SDIO_D5, DCMI_D7, I2C1_SDA and CAN1_TX. |
| 63 | VSS | power_in | Ground pin. |
| 64 | VDD | power_in | Main supply pin for the I/Os and internal regulator; application supply range 1.8 V to 3.6 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (including VDDA, VDD) | VDD-VSS | -0.3 | 4 | V | 81 | ||
| Input voltage on any other pin | VIN | 4 | V | 81 | |||
| Variations between different VDD power pins | /ΔVDDx/ | 50 | mV | 81 | |||
| Variations between all the different ground pins including VREF- | /VSSX −VSS/ | 50 | mV | 81 | |||
| Total current into VDD power lines (source) | IVDD | 240 | mA | 82 | |||
| Total current out of VSS ground lines (sink) | IVSS | 240 | mA | 82 | |||
| Output current sunk by any I/O and control pin | IIO | 25 | mA | 82 | |||
| Output current source by any I/Os and control pin | IIO | 25 | mA | 82 | |||
| Injected current on five-volt tolerant I/O | IINJ(PIN) | -5 | 0 | mA | 82 | ||
| Injected current on any other pin | IINJ(PIN) | -5 | 5 | mA | 82 | ||
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | 25 | mA | 82 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 82 | ||
| Maximum junction temperature | TJ | 125 | °C | 82 | |||
| Internal AHB clock frequency | fHCLK | 0 | 144 | MHz | VOS bit in PWR_CR register = 0 | 82 | |
| Internal AHB clock frequency | fHCLK | 0 | 168 | MHz | VOS bit in PWR_CR register = 1 | 82 | |
| Internal APB1 clock frequency | fPCLK1 | 0 | 42 | MHz | 82 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 84 | MHz | 82 | ||
| Standard operating voltage | VDD | 1.8 | 3.6 | V | 82 | ||
| Analog operating voltage (ADC limited to 1.2 M samples) | VDDA | 1.8 | 2.4 | V | Must be the same potential as VDD | 82 | |
| Analog operating voltage (ADC limited to 1.4 M samples) | VDDA | 2.4 | 3.6 | V | Must be the same potential as VDD | 82 | |
| Backup operating voltage | VBAT | 1.65 | 3.6 | V | 82 | ||
| 1.2 V internal voltage on VCAP_1/VCAP_2 pins (regulator ON) | V12 | 1.08 | 1.14 | 1.2 | V | Regulator ON; VOS bit = 0; max frequency 144 MHz | 83 |
| 1.2 V internal voltage on VCAP_1/VCAP_2 pins (regulator ON) | V12 | 1.2 | 1.26 | 1.32 | V | Regulator ON; VOS bit = 1; max frequency 168 MHz | 83 |
| 1.2 V external voltage on VCAP_1/VCAP_2 pins (regulator OFF) | V12 | 1.1 | 1.14 | 1.2 | V | Regulator OFF; max frequency 144 MHz | 83 |
| 1.2 V external voltage on VCAP_1/VCAP_2 pins (regulator OFF) | V12 | 1.2 | 1.26 | 1.3 | V | Regulator OFF; max frequency 168 MHz | 83 |
| Input voltage on RST and FT pins | VIN | -0.3 | 5.5 | V | 2 V ≤ VDD ≤ 3.6 V | 83 | |
| Input voltage on RST and FT pins | VIN | -0.3 | 5.2 | V | VDD ≤ 2 V | 83 | |
| Input voltage on TTa pins | VIN | -0.3 | V | 83 | |||
| Input voltage on B pin | VIN | 5.5 | V | 83 | |||
| Power dissipation (LQFP64) | PD | 435 | mW | TA = 85 °C for suffix 6 | 83 | ||
| Ambient temperature for 6 suffix version (maximum power dissipation) | TA | -40 | 85 | °C | Maximum power dissipation | 83 | |
| Ambient temperature for 6 suffix version (low-power dissipation) | TA | -40 | 105 | °C | Low-power dissipation | 83 | |
| Junction temperature range, 6 suffix version | TJ | -40 | 105 | °C | 83 | ||
| VDD rise time rate | tVDD | 20 | µs/V | Regulator ON, power-up | 85 | ||
| VDD fall time rate | tVDD | 20 | µs/V | Regulator ON, power-down | 85 | ||
| Power-on/power-down reset threshold (falling edge) | VPOR/PDR | 1.6 | 1.68 | 1.76 | V | Falling edge | 86 |
| Power-on/power-down reset threshold (rising edge) | VPOR/PDR | 1.64 | 1.72 | 1.8 | V | Rising edge | 86 |
| PDR hysteresis | VPDRhyst | 40 | mV | Specified by design | 86 | ||
| Brownout level 1 threshold (falling edge) | VBOR1 | 2.13 | 2.19 | 2.24 | V | Falling edge | 86 |
| Brownout level 1 threshold (rising edge) | VBOR1 | 2.23 | 2.29 | 2.33 | V | Rising edge | 86 |
| Brownout level 2 threshold (falling edge) | VBOR2 | 2.44 | 2.5 | 2.56 | V | Falling edge | 86 |
| Brownout level 2 threshold (rising edge) | VBOR2 | 2.53 | 2.59 | 2.63 | V | Rising edge | 86 |
| Brownout level 3 threshold (falling edge) | VBOR3 | 2.75 | 2.83 | 2.88 | V | Falling edge | 87 |
| Brownout level 3 threshold (rising edge) | VBOR3 | 2.85 | 2.92 | 2.97 | V | Rising edge | 87 |
| BOR hysteresis | VBORhyst | 100 | mV | Specified by design | 87 | ||
| Reset temporization | TRSTTEMPO | 0.5 | 1.5 | 3 | ms | Measured from power-on to first instruction read | 87 |
| InRush energy on voltage regulator power-on (POR or wakeup from Standby) | ERUSH | 5.4 | µC | VDD = 1.8 V, TA = 105 °C, IRUSH = 171 mA for 31 µs | 87 | ||
| Supply current in Run mode, external clock, all peripherals enabled | IDD | 87 | mA | fHCLK = 168 MHz, TA = 25 °C | 88 | ||
| Supply current in Run mode, external clock, all peripherals enabled | IDD | 102 | mA | fHCLK = 168 MHz, TA = 85 °C | 88 | ||
| Supply current in Run mode, external clock, all peripherals enabled | IDD | 109 | mA | fHCLK = 168 MHz, TA = 105 °C | 88 | ||
| Supply current in Stop mode (main regulator in Run mode) | IDD_STOP | 0.45 | 11 | mA | Flash in Stop mode, LS/HS RC and HSE OFF, TA = 85 °C | 93 | |
| Supply current in Stop mode (main regulator in Run mode) | IDD_STOP | 20 | mA | Flash in Stop mode, LS/HS RC and HSE OFF, TA = 105 °C | 93 | ||
| Internal current-consumption dependency: external VCAP capacitance | CEXT | 2.2 | µF | Capacitance of external capacitor (VCAP_1/VCAP_2) | 85 | ||
| ESR of external VCAP capacitor | ESR | 2 | Ω | ESR of external capacitor | 85 | ||
| External user clock source frequency (HSE) | fHSE_ext | 1 | 50 | MHz | 103 | ||
| OSC_IN high or low time | tw(HSE) | 5 | ns | Specified by design | 103 | ||
| OSC_IN rise or fall time | tr(HSE)/tf(HSE) | 10 | ns | Specified by design | 103 | ||
| Duty cycle (HSE external clock) | DuCy(HSE) | 45 | 55 | % | 103 |
CAD (KiCad official)
- Symbol:
STM32F415RGT6TR - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
stm32f415rgt6tr-etched.step/stm32f415rgt6tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32f415rgt6tr.step/stm32f415rgt6tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (208 pp, sha256
077d413280ce588e, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).