3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLM311PWR
Texas Instruments · Comparators · TSSOP-8 (PW)
LM311PWR from Texas Instruments, in a TSSOP-8 (PW). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EMIT OUT | output | Output emitter capable of driving loads referenced to ground or supply rails, rated for maximum 30V from emitter to VCC-. |
| 2 | IN+ | input | Noninverting input of the differential comparator accepting input voltages between VCC- + 0.5V and VCC+ - 1.5V. |
| 3 | IN- | input | Inverting input of the differential comparator accepting input voltages between VCC- + 0.5V and VCC+ - 1.5V. |
| 4 | VCC- | power_in | Negative supply voltage rail with minimum rating of -18V. |
| 5 | BALANCE | input | Offset voltage balance adjustment input. |
| 6 | BAL/STRB | input | Strobe input that drives the output to the off state when pulled low. |
| 7 | COL OUT | output | Output collector capable of driving loads referenced to ground or supply rails, rated for maximum 40V from collector to VCC-. |
| 8 | VCC+ | power_in | Positive supply voltage rail with maximum rating of +18V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSSOP-8 (PW) |
| Category | Amplifiers/Comparators |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage (VCC+ − VCC−) | VCC+ − VCC− | 3.5 | 30 | V | 4 | ||
| Operating free-air temperature range (LM311) | TA | 0 | 70 | °C | LM311 | 4 | |
| Supply voltage VCC+ | VCC+ | 18 | V | Referenced to midpoint of VCC+ and VCC− | 4 | ||
| Supply voltage VCC− | VCC− | -18 | V | Referenced to midpoint of VCC+ and VCC− | 4 | ||
| Supply voltage VCC+ − VCC− | VCC+ − VCC− | 36 | V | 4 | |||
| Differential input voltage | VID | -30 | 30 | V | IN+ with respect to IN− | 4 | |
| Input voltage (either input) | VI | -15 | 15 | V | Magnitude must not exceed supply voltage or ±15 V, whichever is less | 4 | |
| Voltage from emitter output to VCC− | 30 | V | 4 | ||||
| Voltage from collector output to VCC− (LM311) | 40 | V | LM311 | 4 | |||
| Duration of output short circuit to ground | 10 | s | To ground | 4 | |||
| Operating virtual-junction temperature | TJ | 150 | °C | 4 | |||
| Lead temperature (D, P, PS, or PW package) | 260 | °C | 1,6 mm (1/16 inch) from case, 60 s | 4 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| Input offset voltage | VIO | 2 | 7.5 | mV | See (3), 25°C | 6 | |
| Input offset voltage | VIO | 10 | mV | See (3), Full range | 6 | ||
| Input offset current | IIO | 6 | 50 | nA | See (3), 25°C | 6 | |
| Input offset current | IIO | 70 | nA | See (3), Full range | 6 | ||
| Input bias current | IIB | 100 | 250 | nA | 1 V ≤ VO ≤ 14 V, 25°C | 6 | |
| Input bias current | IIB | 300 | nA | 1 V ≤ VO ≤ 14 V, Full range | 6 | ||
| Low-level strobe current | IIL(S) | -3 | mA | V(strobe) = 0.3 V, VID ≤ −10 mV, 25°C | 6 | ||
| Common-mode input-voltage range, lower range | VICR | -14.7 | -14.5 | V | Lower range, Full range | 6 | |
| Common-mode input-voltage range, upper range | VICR | 13 | 13.8 | V | Upper range, Full range | 6 | |
| Large-signal differential-voltage amplification | AVD | 40 | 200 | V/mV | 5 V ≤ VO ≤ 35 V, RL = 1 kΩ, 25°C | 6 | |
| High-level (collector) output leakage current | IOH | 0.2 | 10 | nA | I(strobe) = −3 mA, VID = 5 mV, VOH = 35 V, 25°C | 6 | |
| High-level (collector) output leakage current | IOH | 0.5 | μA | I(strobe) = −3 mA, VID = 5 mV, VOH = 35 V, Full range | 6 | ||
| High-level (collector) output leakage current | IOH | 0.2 | 50 | nA | VID = 5 mV, VOH = 35 V, 25°C | 6 | |
| Low-level (collector-to-emitter) output voltage | VOL | 0.75 | 1.5 | V | IOL = 50 mA, VID = −5 mV, 25°C | 6 | |
| Low-level (collector-to-emitter) output voltage | VOL | 0.23 | 0.4 | V | VCC+ = 4.5 V, VCC− = 0 V, IOL = 8 mA, VID = −6 mV, Full range | 6 | |
| Supply current from VCC+ (output low) | ICC+ | 5.1 | 7.5 | mA | VID = −10 mV, No load, 25°C | 6 | |
| Supply current from VCC− (output high) | ICC− | -4.1 | -5 | mA | VID = 10 mV, No load, 25°C | 6 | |
| Junction-to-ambient thermal resistance (PW TSSOP) | RθJA | 162 | °C/W | 5 | |||
| Junction-to-case (top) thermal resistance (PW TSSOP) | RθJC(top) | 44.6 | °C/W | 5 | |||
| Junction-to-board thermal resistance (PW TSSOP) | RθJB | 93 | °C/W | 5 | |||
| Junction-to-top characterization parameter (PW TSSOP) | ψJT | 2.6 | °C/W | 5 | |||
| Junction-to-board characterization parameter (PW TSSOP) | ψJB | 90.8 | °C/W | 5 |
CAD (Adom-generated)
- Symbol:
LM311PWR - Footprint:
Adom_Gen:Texas_Instruments_PW0008A - 3D model: generated to fit the land (STEP)
- 3D model files:
lm311pwr-etched.step/lm311pwr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm311pwr.step/lm311pwr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (42 pp, sha256
1877bb45737cb7e8, retrieved 2026-11-21) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land. Land: PW0008A 4221848/A land pattern, SLCS007K p.40: 1.5 x 0.45 mm pads, pitch 0.65 mm, pad rows 5.8 mm centre-to-centre. Body from the outline p.39: 3.1/2.9 x 4.5/4.3 body, 6.6/6.2 across the leads, 1.2 MAX, 0.15/0.05 standoff, 8X 0.30/0.19 leads, 6X 0.65 pitch. Shared land Adom_Gen:Texas_Instruments_PW0008A (TI PW0008A EXAMPLE BOARD LAYOUT 4221848/A, ADS1202 SBAS275B p.24). Task master ruling 2026-11-21: TSSOP/SSOP on the lands drawn and sampled (FAMWAVES samples + renders approved).