3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSTM32F373RBT6
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · LQFP-64(10x10)
STM32F373RBT6 from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup power supply for the RTC, the external 32 kHz oscillator and backup registers when VDD is not present, specified at 1.65 to 3.6 V. |
| 2 | PC13 | bidirectional | Standard 3.3 V TC I/O powered through the limited power switch (3 mA sink), so output use is restricted to 2 MHz with 30 pF and it must not drive LEDs; additional functions are WKUP2, ALARM_OUT, CALIB_OUT, TIMESTAMP and RTC_TAMPER1. |
| 3 | PC14 | bidirectional | Standard 3.3 V TC I/O on the same limited backup power switch as PC13 (3 mA), also serving as OSC32_IN for the 32.768 kHz LSE crystal. |
| 4 | PC15 | bidirectional | Standard 3.3 V TC I/O on the same limited backup power switch as PC13 (3 mA), also serving as OSC32_OUT for the 32.768 kHz LSE crystal. |
| 5 | PF0 | bidirectional | 5 V tolerant FTf I/O (Fast-mode Plus capable) that also serves as OSC_IN for the 4 to 32 MHz HSE oscillator, with I2C2_SDA as alternate function. |
| 6 | PF1 | bidirectional | 5 V tolerant FTf I/O (Fast-mode Plus capable) that also serves as OSC_OUT for the HSE oscillator, with I2C2_SCL as alternate function. |
| 7 | NRST | bidirectional | Active-low bidirectional device reset input and internal reset output with embedded weak pull-up (RPU 25 to 55 kOhm); pulses shorter than 100 ns are filtered. |
| 8 | PC0 | bidirectional | 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN10 and TIM5_CH1_ETR as functions. |
| 9 | PC1 | bidirectional | 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN11 and TIM5_CH2 as functions. |
| 10 | PC2 | bidirectional | 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN12, SPI2_MISO/I2S2_MCK and TIM5_CH3 as functions. |
| 11 | PC3 | bidirectional | 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN13, SPI2_MOSI/I2S2_SD and TIM5_CH4 as functions. |
| 12 | VSSA/VREF- | power_in | Analog ground and negative reference voltage for the ADC, comparators and DAC. |
| 13 | VDDA | power_in | Analog power supply for the reset blocks, RCs, PLL, ADC, DACs and comparators, 2.0 to 3.6 V, with a minimum of 2.4 V when the ADC or DAC is used; it must be greater than or equal to VDD. |
| 14 | PA0 | bidirectional | 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN0, WKUP1, COMP1_INM and USART2_CTS among its functions. |
| 15 | PA1 | bidirectional | 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN1, COMP1_INP, RTC_REFIN and USART2_RTS among its functions. |
| 16 | PA2 | bidirectional | 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN2, COMP2_INM, COMP2_OUT and USART2_TX among its functions. |
| 17 | VREF+ | power_in | Positive reference voltage for the ADC and DAC, 2.4 to 3.6 V when used, which must not exceed VDDA. |
| 18 | PA3 | bidirectional | 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN3, COMP2_INP and USART2_RX among its functions. |
| 19 | VDD_2 | power_in | Digital power supply for the I/Os and internal regulator, 2.0 to 3.6 V, which must not exceed VDDA. |
| 20 | PA4 | bidirectional | 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN4, DAC1_OUT1, SPI1_NSS/I2S1_WS and TIM3_CH2 among its functions. |
| 21 | PA5 | bidirectional | 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN5, DAC1_OUT2, SPI1_SCK/I2S1_CK and CEC among its functions. |
| 22 | PA6 | bidirectional | 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN6, DAC2_OUT1, SPI1_MISO/I2S1_MCK and COMP1_OUT among its functions. |
| 23 | PA7 | bidirectional | 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN7, SPI1_MOSI/I2S1_SD, TIM3_CH2 and COMP2_OUT among its functions. |
| 24 | PC4 | bidirectional | 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN14, TSC_G3_IO1, TIM13_CH1 and USART1_TX among its functions. |
| 25 | PC5 | bidirectional | 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN15, TSC_G3_IO2 and USART1_RX among its functions. |
| 26 | PB0 | bidirectional | 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN8, SDADC1_AIN6P, TIM3_CH3 and TSC_G3_IO3 among its functions. |
| 27 | PB1 | bidirectional | 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN9, SDADC1_AIN5P, SDADC1_AIN6M, TIM3_CH4 and TSC_G3_IO4 among its functions. |
| 28 | PB2 | bidirectional | Standard 3.3 V TC I/O powered from VDDSD12 (Table 11 note 3), with SDADC1_AIN4P and SDADC2_AIN6P as functions. |
| 29 | PE8 | bidirectional | Standard 3.3 V TC I/O powered from VDDSD12 (Table 11 note 3), with SDADC1_AIN8P and SDADC2_AIN8P as functions. |
| 30 | PE9 | bidirectional | Standard 3.3 V TC I/O powered from VDDSD12 (Table 11 note 3), with SDADC1_AIN7P, SDADC1_AIN8M, SDADC2_AIN7P and SDADC2_AIN8M as functions. |
| 31 | VSSSD/VREFSD- | power_in | Ground for SDADC1, SDADC2 and SDADC3, combined with the external negative reference VREFSD- (negative input in SDADC single-ended mode). |
| 32 | VDDSD | power_in | Power supply for SDADC1, SDADC2 and SDADC3, 2.2 to 3.6 V when the SDADC is used, which must not exceed VDDA. |
| 33 | VREFSD+ | power_in | External positive reference voltage for SDADC1, SDADC2 and SDADC3, 1.1 to 3.6 V, which must not exceed any VDDSDx. |
| 34 | PB14 | bidirectional | Standard 3.3 V TC I/O powered from VDDSD3 (Table 11 note 4), with SDADC3_AIN8P, SPI2_MISO/I2S2_MCK, TIM15_CH1 and TSC_G6_IO1 as functions. |
| 35 | PB15 | bidirectional | Standard 3.3 V TC I/O powered from VDDSD3 (Table 11 note 4), with SDADC3_AIN7P, SDADC3_AIN8M, SPI2_MOSI/I2S2_SD and RTC_REFIN as functions. |
| 36 | PD8 | bidirectional | Standard 3.3 V TC I/O powered from VDDSD3 (Table 11 note 4), with SDADC3_AIN6P, SPI2_SCK/I2S2_CK, USART3_TX and TSC_G6_IO3 as functions. |
| 37 | PC6 | bidirectional | 5 V tolerant FT I/O with TIM3_CH1 and SPI1_NSS/I2S1_WS as alternate functions. |
| 38 | PC7 | bidirectional | 5 V tolerant FT I/O with TIM3_CH2 and SPI1_SCK/I2S1_CK as alternate functions. |
| 39 | PC8 | bidirectional | 5 V tolerant FT I/O with TIM3_CH3 and SPI1_MISO/I2S1_MCK as alternate functions. |
| 40 | PC9 | bidirectional | 5 V tolerant FT I/O with TIM3_CH4 and SPI1_MOSI/I2S1_SD as alternate functions. |
| 41 | PA8 | bidirectional | 5 V tolerant FT I/O with MCO, TIM5_CH1_ETR, I2C2_SMBA, USART1_CK and TIM4_ETR as alternate functions. |
| 42 | PA9 | bidirectional | 5 V tolerant FTf I/O (Fast-mode Plus capable) with USART1_TX, I2C2_SCL, TIM15_BKIN and TSC_G4_IO1 as alternate functions. |
| 43 | PA10 | bidirectional | 5 V tolerant FTf I/O (Fast-mode Plus capable) with USART1_RX, I2C2_SDA, TIM17_BKIN and TSC_G4_IO2 as alternate functions. |
| 44 | PA11 | bidirectional | 5 V tolerant FT I/O with USART1_CTS, CAN_RX, USB_DM, TIM4_CH1 and COMP1_OUT as alternate functions. |
| 45 | PA12 | bidirectional | 5 V tolerant FT I/O with USART1_RTS, CAN_TX, USB_DP, TIM16_CH1 and COMP2_OUT as alternate functions. |
| 46 | PA13 | bidirectional | 5 V tolerant FT I/O that also carries the SWDIO-JTMS debug function, with IR_OUT, USART3_CTS and TSC_G4_IO3 as alternate functions. |
| 47 | PF6 | bidirectional | 5 V tolerant FTf I/O (Fast-mode Plus capable) with SPI1_MOSI/I2S1_SD, USART3_RTS, TIM4_CH4 and I2C2_SCL as alternate functions. |
| 48 | PF7 | bidirectional | 5 V tolerant FTf I/O (Fast-mode Plus capable) with I2C2_SDA and USART2_CK as alternate functions. |
| 49 | PA14 | bidirectional | 5 V tolerant FTf I/O (Fast-mode Plus capable) that also carries the SWCLK-JTCK debug function, with I2C1_SDA, TIM12_CH1 and TSC_G4_IO4 as alternate functions. |
| 50 | PA15 | bidirectional | 5 V tolerant FTf I/O (Fast-mode Plus capable) that also carries the JTDI debug function, with SPI1_NSS/I2S1_WS, I2C1_SCL, TIM2_CH1_ETR and TSC_SYNC as alternate functions. |
| 51 | PC10 | bidirectional | 5 V tolerant FT I/O with SPI3_SCK/I2S3_CK, USART3_TX and TIM19_CH1 as alternate functions. |
| 52 | PC11 | bidirectional | 5 V tolerant FT I/O with SPI3_MISO/I2S3_MCK, USART3_RX and TIM19_CH2 as alternate functions. |
| 53 | PC12 | bidirectional | 5 V tolerant FT I/O with SPI3_MOSI/I2S3_SD, USART3_CK and TIM19_CH3 as alternate functions. |
| 54 | PD2 | bidirectional | 5 V tolerant FT I/O with TIM3_ETR as alternate function. |
| 55 | PB3 | bidirectional | 5 V tolerant FT I/O that also carries the JTDO-TRACESWO debug function, with SPI1_SCK/I2S1_CK, USART2_TX, TIM2_CH2, TIM3_ETR and TSC_G5_IO1 as alternate functions. |
| 56 | PB4 | bidirectional | 5 V tolerant FT I/O that also carries the NJTRST debug function, with SPI1_MISO/I2S1_MCK, USART2_RX, TIM3_CH1, TIM16_CH1 and TSC_G5_IO2 as alternate functions. |
| 57 | PB5 | bidirectional | 5 V tolerant FT I/O with SPI1_MOSI/I2S1_SD, I2C1_SMBA, USART2_CK, TIM3_CH2, TIM16_BKIN and TIM17_CH1 as alternate functions. |
| 58 | PB6 | bidirectional | 5 V tolerant FTf I/O (Fast-mode Plus capable) with I2C1_SCL, USART1_TX, TIM4_CH1, TIM16_CH1N and TSC_G5_IO3 as alternate functions. |
| 59 | PB7 | bidirectional | 5 V tolerant FTf I/O (Fast-mode Plus capable) with I2C1_SDA, USART1_RX, TIM4_CH2, TIM17_CH1N and TSC_G5_IO4 as alternate functions. |
| 60 | BOOT0 | input | Dedicated BOOT0 input (0 to 5.5 V) that selects the boot memory together with the Boot1 option bit. |
| 61 | PB8 | bidirectional | 5 V tolerant FTf I/O (Fast-mode Plus capable) with SPI2_SCK/I2S2_CK, I2C1_SCL, USART3_TX, CAN_RX, CEC, TIM16_CH1 and COMP1_OUT as alternate functions. |
| 62 | PB9 | bidirectional | 5 V tolerant FTf I/O (Fast-mode Plus capable) with SPI2_NSS/I2S2_WS, I2C1_SDA, USART3_RX, CAN_TX, IR_OUT, TIM17_CH1 and COMP2_OUT as alternate functions. |
| 63 | VSS_1 | power_in | Digital ground pin; variations between all ground pins must stay within 50 mV (Table 19). |
| 64 | VDD_1 | power_in | Digital power supply for the I/Os and internal regulator, 2.0 to 3.6 V (Table 22). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (including VDDA, VDDSDx, VBAT and VDD) | VDD-VSS | -0.3 | 4 | V | including VDDA, VDDSDx, VBAT and VDD | 55 | |
| Allowed voltage difference for VDD > VDDA | VDD-VDDA | 0.4 | V | for VDD > VDDA | 55 | ||
| Allowed voltage difference for VDDSDx > VDDA | VDDSDx, VDDA | 0.4 | V | for VDDSDx > VDDA | 55 | ||
| Allowed voltage difference for VREFSD+ > VDDSD3 | VREFSD+, VDDSD3 | 0.4 | V | for VREFSD+ > VDDSD3 | 55 | ||
| Allowed voltage difference for VREF+ > VDDA | VREF+, VDDA | 0.4 | V | for VREF+ > VDDA | 55 | ||
| Input voltage on FT and FTf pins | VIN | -0.3 | V | 55 | |||
| Input voltage on TTa pins | VIN | -0.3 | 4 | V | 55 | ||
| Input voltage on TC pins on SDADCx channels inputs | VIN | -0.3 | 4 | V | 55 | ||
| Input voltage on any other pin | VIN | -0.3 | 4 | V | 55 | ||
| Variations between all the different ground pins | /VSSX - VSS/ | 50 | mV | 55 | |||
| Variations between VREFSD- and VSSx | /VREFSD- - VSSx/ | 50 | mV | 55 | |||
| Total current into sum of all VDD_x and VDDSDx power lines (source) | ΣIVDD | 160 | mA | 56 | |||
| Total current out of sum of all VSS_x and VSSSD ground lines (sink) | ΣIVSS | -160 | mA | 56 | |||
| Maximum current into each VDD_x or VDDSDx power pin (source) | IVDD(PIN) | 100 | mA | 56 | |||
| Maximum current out of each VSS_x or VSSSD ground pin (sink) | IVSS(PIN) | -100 | mA | 56 | |||
| Output current sunk by any I/O and control pin | IIO(PIN) | 25 | mA | 56 | |||
| Output current source by any I/O and control pin | IIO(PIN) | -25 | mA | 56 | |||
| Total output current sunk by sum of all IOs and control pins | ΣIIO(PIN) | 80 | mA | 56 | |||
| Total output current sourced by sum of all IOs and control pins | ΣIIO(PIN) | -80 | mA | 56 | |||
| Injected current on FT, FTf and B pins | IINJ(PIN) | -5 | 0 | mA | 56 | ||
| Injected current on TC and RST pin | IINJ(PIN) | -5 | 5 | mA | 56 | ||
| Injected current on TTa pins | IINJ(PIN) | -5 | 5 | mA | 56 | ||
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | 25 | mA | 56 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 56 | ||
| Maximum junction temperature | TJ | 150 | °C | 56 | |||
| Internal AHB clock frequency | fHCLK | 0 | 72 | MHz | 57 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 36 | MHz | 57 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 72 | MHz | 57 | ||
| Standard operating voltage | VDD | 2 | 3.6 | V | Must have a potential equal to or lower than VDDA | 57 | |
| Analog operating voltage (ADC and DAC used) | VDDA | 2.4 | 3.6 | V | Must have a potential equal to or higher than VDD | 57 | |
| Analog operating voltage (ADC and DAC not used) | VDDA | 2 | 3.6 | V | 57 | ||
| VDDSD12 operating voltage (SDADC used) | VDDSD12 | 2.2 | 3.6 | V | Must have a potential equal to or lower than VDDA | 57 | |
| VDDSD12 operating voltage (SDADC not used) | VDDSD12 | 2 | 3.6 | V | 57 | ||
| VDDSD3 operating voltage (SDADC used) | VDDSD3 | 2.2 | 3.6 | V | Must have a potential equal to or lower than VDDA | 57 | |
| VDDSD3 operating voltage (SDADC not used) | VDDSD3 | 2 | 3.6 | V | 57 | ||
| Positive reference voltage (ADC and DAC used) | VREF+ | 2.4 | 3.6 | V | Must have a potential equal to or lower than VDDA | 57 | |
| Positive reference voltage (ADC and DAC not used) | VREF+ | 2 | 3.6 | V | 57 | ||
| SDADCx positive reference voltage | VREFSD+ | 1.1 | 3.6 | V | Must have a potential equal to or lower than any VDDSDx | 57 | |
| Backup operating voltage | VBAT | 1.65 | 3.6 | V | 57 | ||
| Input voltage on FT and FTf pins | VIN | -0.3 | 5.5 | V | 57 | ||
| Input voltage on TTa pins | VIN | -0.3 | V | 57 | |||
| Input voltage on TC pins on SDADCx channels inputs | VIN | -0.3 | V | 57 | |||
| Input voltage on BOOT0 pin | VIN | 0 | 5.5 | V | 57 | ||
| Input voltage on any other pin | VIN | -0.3 | V | 57 | |||
| Power dissipation (LQFP64) | PD | 444 | mW | TA = 85 °C for suffix 6 | 57 | ||
| Ambient temperature for 6 suffix version (maximum power dissipation) | TA | -40 | 85 | °C | Maximum power dissipation | 58 | |
| Ambient temperature for 6 suffix version (low power dissipation) | TA | -40 | 105 | °C | Low power dissipation | 58 | |
| Junction temperature range, 6 suffix version | TJ | -40 | 105 | °C | 6 suffix version | 58 | |
| Power on/power down reset threshold | VPOR/PDR | 1.8 | 1.88 | 1.96 | V | Falling edge | 59 |
| Power on/power down reset threshold | VPOR/PDR | 1.84 | 1.92 | 2 | V | Rising edge | 59 |
| POR reset temporization | tRSTTEMPO | 1.5 | 2.5 | 4.5 | ms | 59 | |
| Internal reference voltage | VREFINT | 1.2 | 1.23 | 1.25 | V | -40 °C < TA < +105 °C | 60 |
| Internal reference voltage spread over the temperature range | VREFINT_s | 10 | mV | VDD = 3 V | 60 | ||
| Temperature coefficient | TCoeff | 100 | ppm/°C | 60 | |||
| Startup time | tSTART | 10 | µs | 60 | |||
| Supply current in Run mode, code executing from Flash, 72 MHz, max at 85 °C | IDD | 63.1 | 71.5 | mA | VDD = 3.6 V; HSE bypass, PLL on; all peripherals enabled; max at TA = 85 °C | 61 | |
| Supply current in Run mode, code executing from Flash, 72 MHz, max at 105 °C | IDD | 63.1 | 73.4 | mA | VDD = 3.6 V; HSE bypass, PLL on; all peripherals enabled; max at TA = 105 °C | 61 | |
| Supply current in Stop mode, regulators in run mode, all oscillators OFF, max at 85 °C | IDD | 480 | µA | Regulators in run mode, all oscillators OFF; VDD = VDDA; max at TA = 85 °C | 63 | ||
| Supply current in Stop mode, regulators in run mode, all oscillators OFF, max at 105 °C | IDD | 1019 | µA | Regulators in run mode, all oscillators OFF; VDD = VDDA; max at TA = 105 °C | 63 | ||
| Supply current in Standby mode, LSI OFF and IWDG OFF, max at 85 °C | IDD | 3.5 | µA | LSI OFF and IWDG OFF; VDD = VDDA; max at TA = 85 °C | 63 |
CAD (KiCad official)
- Symbol:
STM32F373RBT6 - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
stm32f373rbt6-etched.step/stm32f373rbt6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32f373rbt6.step/stm32f373rbt6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (137 pp, sha256
a670e6a0a2ed996b, retrieved 2026-11-10, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).