Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

STM32F373RBT6

STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · LQFP-64(10x10)

STM32F373RBT6 from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VBAT power_in Backup power supply for the RTC, the external 32 kHz oscillator and backup registers when VDD is not present, specified at 1.65 to 3.6 V.
2 PC13 bidirectional Standard 3.3 V TC I/O powered through the limited power switch (3 mA sink), so output use is restricted to 2 MHz with 30 pF and it must not drive LEDs; additional functions are WKUP2, ALARM_OUT, CALIB_OUT, TIMESTAMP and RTC_TAMPER1.
3 PC14 bidirectional Standard 3.3 V TC I/O on the same limited backup power switch as PC13 (3 mA), also serving as OSC32_IN for the 32.768 kHz LSE crystal.
4 PC15 bidirectional Standard 3.3 V TC I/O on the same limited backup power switch as PC13 (3 mA), also serving as OSC32_OUT for the 32.768 kHz LSE crystal.
5 PF0 bidirectional 5 V tolerant FTf I/O (Fast-mode Plus capable) that also serves as OSC_IN for the 4 to 32 MHz HSE oscillator, with I2C2_SDA as alternate function.
6 PF1 bidirectional 5 V tolerant FTf I/O (Fast-mode Plus capable) that also serves as OSC_OUT for the HSE oscillator, with I2C2_SCL as alternate function.
7 NRST bidirectional Active-low bidirectional device reset input and internal reset output with embedded weak pull-up (RPU 25 to 55 kOhm); pulses shorter than 100 ns are filtered.
8 PC0 bidirectional 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN10 and TIM5_CH1_ETR as functions.
9 PC1 bidirectional 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN11 and TIM5_CH2 as functions.
10 PC2 bidirectional 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN12, SPI2_MISO/I2S2_MCK and TIM5_CH3 as functions.
11 PC3 bidirectional 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN13, SPI2_MOSI/I2S2_SD and TIM5_CH4 as functions.
12 VSSA/VREF- power_in Analog ground and negative reference voltage for the ADC, comparators and DAC.
13 VDDA power_in Analog power supply for the reset blocks, RCs, PLL, ADC, DACs and comparators, 2.0 to 3.6 V, with a minimum of 2.4 V when the ADC or DAC is used; it must be greater than or equal to VDD.
14 PA0 bidirectional 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN0, WKUP1, COMP1_INM and USART2_CTS among its functions.
15 PA1 bidirectional 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN1, COMP1_INP, RTC_REFIN and USART2_RTS among its functions.
16 PA2 bidirectional 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN2, COMP2_INM, COMP2_OUT and USART2_TX among its functions.
17 VREF+ power_in Positive reference voltage for the ADC and DAC, 2.4 to 3.6 V when used, which must not exceed VDDA.
18 PA3 bidirectional 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN3, COMP2_INP and USART2_RX among its functions.
19 VDD_2 power_in Digital power supply for the I/Os and internal regulator, 2.0 to 3.6 V, which must not exceed VDDA.
20 PA4 bidirectional 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN4, DAC1_OUT1, SPI1_NSS/I2S1_WS and TIM3_CH2 among its functions.
21 PA5 bidirectional 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN5, DAC1_OUT2, SPI1_SCK/I2S1_CK and CEC among its functions.
22 PA6 bidirectional 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN6, DAC2_OUT1, SPI1_MISO/I2S1_MCK and COMP1_OUT among its functions.
23 PA7 bidirectional 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN7, SPI1_MOSI/I2S1_SD, TIM3_CH2 and COMP2_OUT among its functions.
24 PC4 bidirectional 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN14, TSC_G3_IO1, TIM13_CH1 and USART1_TX among its functions.
25 PC5 bidirectional 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN15, TSC_G3_IO2 and USART1_RX among its functions.
26 PB0 bidirectional 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN8, SDADC1_AIN6P, TIM3_CH3 and TSC_G3_IO3 among its functions.
27 PB1 bidirectional 3.3 V tolerant TTa I/O directly connected to the ADC, with ADC_IN9, SDADC1_AIN5P, SDADC1_AIN6M, TIM3_CH4 and TSC_G3_IO4 among its functions.
28 PB2 bidirectional Standard 3.3 V TC I/O powered from VDDSD12 (Table 11 note 3), with SDADC1_AIN4P and SDADC2_AIN6P as functions.
29 PE8 bidirectional Standard 3.3 V TC I/O powered from VDDSD12 (Table 11 note 3), with SDADC1_AIN8P and SDADC2_AIN8P as functions.
30 PE9 bidirectional Standard 3.3 V TC I/O powered from VDDSD12 (Table 11 note 3), with SDADC1_AIN7P, SDADC1_AIN8M, SDADC2_AIN7P and SDADC2_AIN8M as functions.
31 VSSSD/VREFSD- power_in Ground for SDADC1, SDADC2 and SDADC3, combined with the external negative reference VREFSD- (negative input in SDADC single-ended mode).
32 VDDSD power_in Power supply for SDADC1, SDADC2 and SDADC3, 2.2 to 3.6 V when the SDADC is used, which must not exceed VDDA.
33 VREFSD+ power_in External positive reference voltage for SDADC1, SDADC2 and SDADC3, 1.1 to 3.6 V, which must not exceed any VDDSDx.
34 PB14 bidirectional Standard 3.3 V TC I/O powered from VDDSD3 (Table 11 note 4), with SDADC3_AIN8P, SPI2_MISO/I2S2_MCK, TIM15_CH1 and TSC_G6_IO1 as functions.
35 PB15 bidirectional Standard 3.3 V TC I/O powered from VDDSD3 (Table 11 note 4), with SDADC3_AIN7P, SDADC3_AIN8M, SPI2_MOSI/I2S2_SD and RTC_REFIN as functions.
36 PD8 bidirectional Standard 3.3 V TC I/O powered from VDDSD3 (Table 11 note 4), with SDADC3_AIN6P, SPI2_SCK/I2S2_CK, USART3_TX and TSC_G6_IO3 as functions.
37 PC6 bidirectional 5 V tolerant FT I/O with TIM3_CH1 and SPI1_NSS/I2S1_WS as alternate functions.
38 PC7 bidirectional 5 V tolerant FT I/O with TIM3_CH2 and SPI1_SCK/I2S1_CK as alternate functions.
39 PC8 bidirectional 5 V tolerant FT I/O with TIM3_CH3 and SPI1_MISO/I2S1_MCK as alternate functions.
40 PC9 bidirectional 5 V tolerant FT I/O with TIM3_CH4 and SPI1_MOSI/I2S1_SD as alternate functions.
41 PA8 bidirectional 5 V tolerant FT I/O with MCO, TIM5_CH1_ETR, I2C2_SMBA, USART1_CK and TIM4_ETR as alternate functions.
42 PA9 bidirectional 5 V tolerant FTf I/O (Fast-mode Plus capable) with USART1_TX, I2C2_SCL, TIM15_BKIN and TSC_G4_IO1 as alternate functions.
43 PA10 bidirectional 5 V tolerant FTf I/O (Fast-mode Plus capable) with USART1_RX, I2C2_SDA, TIM17_BKIN and TSC_G4_IO2 as alternate functions.
44 PA11 bidirectional 5 V tolerant FT I/O with USART1_CTS, CAN_RX, USB_DM, TIM4_CH1 and COMP1_OUT as alternate functions.
45 PA12 bidirectional 5 V tolerant FT I/O with USART1_RTS, CAN_TX, USB_DP, TIM16_CH1 and COMP2_OUT as alternate functions.
46 PA13 bidirectional 5 V tolerant FT I/O that also carries the SWDIO-JTMS debug function, with IR_OUT, USART3_CTS and TSC_G4_IO3 as alternate functions.
47 PF6 bidirectional 5 V tolerant FTf I/O (Fast-mode Plus capable) with SPI1_MOSI/I2S1_SD, USART3_RTS, TIM4_CH4 and I2C2_SCL as alternate functions.
48 PF7 bidirectional 5 V tolerant FTf I/O (Fast-mode Plus capable) with I2C2_SDA and USART2_CK as alternate functions.
49 PA14 bidirectional 5 V tolerant FTf I/O (Fast-mode Plus capable) that also carries the SWCLK-JTCK debug function, with I2C1_SDA, TIM12_CH1 and TSC_G4_IO4 as alternate functions.
50 PA15 bidirectional 5 V tolerant FTf I/O (Fast-mode Plus capable) that also carries the JTDI debug function, with SPI1_NSS/I2S1_WS, I2C1_SCL, TIM2_CH1_ETR and TSC_SYNC as alternate functions.
51 PC10 bidirectional 5 V tolerant FT I/O with SPI3_SCK/I2S3_CK, USART3_TX and TIM19_CH1 as alternate functions.
52 PC11 bidirectional 5 V tolerant FT I/O with SPI3_MISO/I2S3_MCK, USART3_RX and TIM19_CH2 as alternate functions.
53 PC12 bidirectional 5 V tolerant FT I/O with SPI3_MOSI/I2S3_SD, USART3_CK and TIM19_CH3 as alternate functions.
54 PD2 bidirectional 5 V tolerant FT I/O with TIM3_ETR as alternate function.
55 PB3 bidirectional 5 V tolerant FT I/O that also carries the JTDO-TRACESWO debug function, with SPI1_SCK/I2S1_CK, USART2_TX, TIM2_CH2, TIM3_ETR and TSC_G5_IO1 as alternate functions.
56 PB4 bidirectional 5 V tolerant FT I/O that also carries the NJTRST debug function, with SPI1_MISO/I2S1_MCK, USART2_RX, TIM3_CH1, TIM16_CH1 and TSC_G5_IO2 as alternate functions.
57 PB5 bidirectional 5 V tolerant FT I/O with SPI1_MOSI/I2S1_SD, I2C1_SMBA, USART2_CK, TIM3_CH2, TIM16_BKIN and TIM17_CH1 as alternate functions.
58 PB6 bidirectional 5 V tolerant FTf I/O (Fast-mode Plus capable) with I2C1_SCL, USART1_TX, TIM4_CH1, TIM16_CH1N and TSC_G5_IO3 as alternate functions.
59 PB7 bidirectional 5 V tolerant FTf I/O (Fast-mode Plus capable) with I2C1_SDA, USART1_RX, TIM4_CH2, TIM17_CH1N and TSC_G5_IO4 as alternate functions.
60 BOOT0 input Dedicated BOOT0 input (0 to 5.5 V) that selects the boot memory together with the Boot1 option bit.
61 PB8 bidirectional 5 V tolerant FTf I/O (Fast-mode Plus capable) with SPI2_SCK/I2S2_CK, I2C1_SCL, USART3_TX, CAN_RX, CEC, TIM16_CH1 and COMP1_OUT as alternate functions.
62 PB9 bidirectional 5 V tolerant FTf I/O (Fast-mode Plus capable) with SPI2_NSS/I2S2_WS, I2C1_SDA, USART3_RX, CAN_TX, IR_OUT, TIM17_CH1 and COMP2_OUT as alternate functions.
63 VSS_1 power_in Digital ground pin; variations between all ground pins must stay within 50 mV (Table 19).
64 VDD_1 power_in Digital power supply for the I/Os and internal regulator, 2.0 to 3.6 V (Table 22).

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package LQFP-64(10x10)
Category Embedded Processors & Controllers
Pins 64

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
External main supply voltage (including VDDA, VDDSDx, VBAT and VDD) VDD-VSS -0.3 4 V including VDDA, VDDSDx, VBAT and VDD 55
Allowed voltage difference for VDD > VDDA VDD-VDDA 0.4 V for VDD > VDDA 55
Allowed voltage difference for VDDSDx > VDDA VDDSDx, VDDA 0.4 V for VDDSDx > VDDA 55
Allowed voltage difference for VREFSD+ > VDDSD3 VREFSD+, VDDSD3 0.4 V for VREFSD+ > VDDSD3 55
Allowed voltage difference for VREF+ > VDDA VREF+, VDDA 0.4 V for VREF+ > VDDA 55
Input voltage on FT and FTf pins VIN -0.3 V 55
Input voltage on TTa pins VIN -0.3 4 V 55
Input voltage on TC pins on SDADCx channels inputs VIN -0.3 4 V 55
Input voltage on any other pin VIN -0.3 4 V 55
Variations between all the different ground pins /VSSX - VSS/ 50 mV 55
Variations between VREFSD- and VSSx /VREFSD- - VSSx/ 50 mV 55
Total current into sum of all VDD_x and VDDSDx power lines (source) ΣIVDD 160 mA 56
Total current out of sum of all VSS_x and VSSSD ground lines (sink) ΣIVSS -160 mA 56
Maximum current into each VDD_x or VDDSDx power pin (source) IVDD(PIN) 100 mA 56
Maximum current out of each VSS_x or VSSSD ground pin (sink) IVSS(PIN) -100 mA 56
Output current sunk by any I/O and control pin IIO(PIN) 25 mA 56
Output current source by any I/O and control pin IIO(PIN) -25 mA 56
Total output current sunk by sum of all IOs and control pins ΣIIO(PIN) 80 mA 56
Total output current sourced by sum of all IOs and control pins ΣIIO(PIN) -80 mA 56
Injected current on FT, FTf and B pins IINJ(PIN) -5 0 mA 56
Injected current on TC and RST pin IINJ(PIN) -5 5 mA 56
Injected current on TTa pins IINJ(PIN) -5 5 mA 56
Total injected current (sum of all I/O and control pins) ΣIINJ(PIN) -25 25 mA 56
Storage temperature range TSTG -65 150 °C 56
Maximum junction temperature TJ 150 °C 56
Internal AHB clock frequency fHCLK 0 72 MHz 57
Internal APB1 clock frequency fPCLK1 0 36 MHz 57
Internal APB2 clock frequency fPCLK2 0 72 MHz 57
Standard operating voltage VDD 2 3.6 V Must have a potential equal to or lower than VDDA 57
Analog operating voltage (ADC and DAC used) VDDA 2.4 3.6 V Must have a potential equal to or higher than VDD 57
Analog operating voltage (ADC and DAC not used) VDDA 2 3.6 V 57
VDDSD12 operating voltage (SDADC used) VDDSD12 2.2 3.6 V Must have a potential equal to or lower than VDDA 57
VDDSD12 operating voltage (SDADC not used) VDDSD12 2 3.6 V 57
VDDSD3 operating voltage (SDADC used) VDDSD3 2.2 3.6 V Must have a potential equal to or lower than VDDA 57
VDDSD3 operating voltage (SDADC not used) VDDSD3 2 3.6 V 57
Positive reference voltage (ADC and DAC used) VREF+ 2.4 3.6 V Must have a potential equal to or lower than VDDA 57
Positive reference voltage (ADC and DAC not used) VREF+ 2 3.6 V 57
SDADCx positive reference voltage VREFSD+ 1.1 3.6 V Must have a potential equal to or lower than any VDDSDx 57
Backup operating voltage VBAT 1.65 3.6 V 57
Input voltage on FT and FTf pins VIN -0.3 5.5 V 57
Input voltage on TTa pins VIN -0.3 V 57
Input voltage on TC pins on SDADCx channels inputs VIN -0.3 V 57
Input voltage on BOOT0 pin VIN 0 5.5 V 57
Input voltage on any other pin VIN -0.3 V 57
Power dissipation (LQFP64) PD 444 mW TA = 85 °C for suffix 6 57
Ambient temperature for 6 suffix version (maximum power dissipation) TA -40 85 °C Maximum power dissipation 58
Ambient temperature for 6 suffix version (low power dissipation) TA -40 105 °C Low power dissipation 58
Junction temperature range, 6 suffix version TJ -40 105 °C 6 suffix version 58
Power on/power down reset threshold VPOR/PDR 1.8 1.88 1.96 V Falling edge 59
Power on/power down reset threshold VPOR/PDR 1.84 1.92 2 V Rising edge 59
POR reset temporization tRSTTEMPO 1.5 2.5 4.5 ms 59
Internal reference voltage VREFINT 1.2 1.23 1.25 V -40 °C < TA < +105 °C 60
Internal reference voltage spread over the temperature range VREFINT_s 10 mV VDD = 3 V 60
Temperature coefficient TCoeff 100 ppm/°C 60
Startup time tSTART 10 µs 60
Supply current in Run mode, code executing from Flash, 72 MHz, max at 85 °C IDD 63.1 71.5 mA VDD = 3.6 V; HSE bypass, PLL on; all peripherals enabled; max at TA = 85 °C 61
Supply current in Run mode, code executing from Flash, 72 MHz, max at 105 °C IDD 63.1 73.4 mA VDD = 3.6 V; HSE bypass, PLL on; all peripherals enabled; max at TA = 105 °C 61
Supply current in Stop mode, regulators in run mode, all oscillators OFF, max at 85 °C IDD 480 µA Regulators in run mode, all oscillators OFF; VDD = VDDA; max at TA = 85 °C 63
Supply current in Stop mode, regulators in run mode, all oscillators OFF, max at 105 °C IDD 1019 µA Regulators in run mode, all oscillators OFF; VDD = VDDA; max at TA = 105 °C 63
Supply current in Standby mode, LSI OFF and IWDG OFF, max at 85 °C IDD 3.5 µA LSI OFF and IWDG OFF; VDD = VDDA; max at TA = 85 °C 63

CAD (KiCad official)

  • Symbol: STM32F373RBT6
  • Footprint: Package_QFP:LQFP-64_10x10mm_P0.5mm
  • 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
  • 3D model files: stm32f373rbt6-etched.step / stm32f373rbt6-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm32f373rbt6.step / stm32f373rbt6.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (137 pp, sha256 a670e6a0a2ed996b, retrieved 2026-11-10, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF