3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownLD59150PUR
STMicroelectronics · Linear Voltage Regulators (LDO) · DFN10(3x3)
LD59150PUR from STMicroelectronics, in a DFN10(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input supply pin for the LDO pass element, operating from 0.8 V to 5.5 V per the electrical characteristics. |
| 2 | VIN | power_in | Input supply pin (paired with pin 1) for the LDO pass element, operating from 0.8 V to 5.5 V per the electrical characteristics. |
| 3 | PG | output | Power Good open-drain flag that goes high impedance when VOUT exceeds VIT + VHYS and is pulled low when VOUT falls below VIT or the device is disabled; it needs an external pull-up of 10 kΩ to 1 MΩ to a potential below 5.5 V and sinks up to 1.5 mA. |
| 4 | VBIAS | power_in | Bias supply pin that must be supplied from 2.7 V to 5.5 V for the internal circuitry. |
| 5 | EN | input | Enable logic input where low (below 0.4 V) shuts the device down and high (above 1.1 V) activates it, and it must not be left floating. |
| 6 | GND | power_in | Ground reference pin to which all voltages are referred and which must also be connected to the exposed pad. |
| 7 | SS | passive | Soft-start pin where an external capacitor CSS sets the output ramp time by being charged with a constant 0.44 µA typical current. |
| 8 | FB | input | Feedback pin connected to the internal 0.8 V reference, used with an external resistor divider to set the output voltage from 0.8 V to 3.6 V. |
| 9 | VOUT | power_out | Regulated output pin delivering up to 1.5 A, with DC output voltage limited to -0.3 V to VIN + 0.3 V. |
| 10 | VOUT | power_out | Regulated output pin (paired with pin 9) delivering up to 1.5 A, with DC output voltage limited to -0.3 V to VIN + 0.3 V. |
| 11 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | DFN10(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Bias pin voltage | VBIAS | 2.7 | 5.5 | V | 6 | ||
| Input voltage absolute maximum | VIN | -0.3 | 6 | V | Input voltage pin | 5 | |
| Bias supply absolute maximum | VBIAS | -0.3 | 6 | V | Bias supply pin | 5 | |
| Enable input voltage absolute maximum | VEN | -0.3 | 6 | V | Enable input voltage | 5 | |
| Adjustable pin voltage absolute maximum | VADJ | -0.3 | 6 | V | Adjustable pin voltage | 5 | |
| Soft-start pin voltage absolute maximum | VSS | -0.3 | 6 | V | Soft-start pin | 5 | |
| Power Good pin voltage absolute maximum | VPG | -0.3 | 6 | V | Power Good pin | 5 | |
| Power Good sink current | IPG | 0 | 1.5 | mA | Power Good sink current | 5 | |
| Storage temperature range | TST | -55 | 150 | °C | 5 | ||
| Operating junction temperature range | TJ | -40 | 150 | °C | 5 | ||
| Thermal resistance junction-ambient | RthJA | 47.5 | °C/W | 4 layer JEDEC PCB (2S2P) test board with thermal vias | 5 | ||
| Thermal resistance junction-case | RthJC | 8 | °C/W | 4 layer JEDEC PCB (2S2P) test board with thermal vias | 5 | ||
| Reference voltage | VREF | 0.796 | 0.8 | 0.804 | V | T = + 25 °C | 6 |
| Output voltage accuracy | VOUT | -2 | 0.5 | 2 | % | 50 mA < IOUT < 1.5 A, 2.97 V < VBIAS < 5.5 V | 6 |
| VIN dropout voltage | Vdrop | 65 | 125 | mV | IOUT = 1.5 A, VBIAS - VOUT > 3.25 V | 6 | |
| VBIAS dropout voltage | Vdrop | 0.92 | 1.1 | V | IOUT = 1.5 A VIN = VBIAS | 6 | |
| Current limit | Icl | 2 | 3 | 5.5 | A | VOUT = 80% x VOUT(nom) | 6 |
| Bias pin current | IBIAS | 0.88 | 1.5 | mA | 6 | ||
| Shutdown supply current | ISHDN | 1 | 50 | µA | VEN < 0.4 V (measured through GND) | 6 | |
| Feedback pin current | IFB | -1 | 0.001 | 1 | µA | 6 | |
| Line regulation | 0.01 | %/V | VOUT(nom) + 0.3 V < VIN < 5.5 V | 6 | |||
| Load regulation | 0.02 | %/A | 50 mA < IOUT < 1.5 A | 6 | |||
| Soft-start charging current | ISS | 0.44 | µA | VSS = 0.4 V | 6 | ||
| Minimum start-up time | Tstr | 100 | µs | IOUT = 1 A, CSS = floating | 6 | ||
| Enable input high | VEN-H | 1.1 | 5.5 | V | 6 | ||
| Enable input low | VEN-L | 0 | 0.4 | V | 6 | ||
| Enable hysteresis | VEN-Hyst | 50 | mV | 6 | |||
| Enable deglitch time | TDG | 20 | µs | 6 | |||
| Enable pin current | IEN | 0.1 | 1 | µA | VEN = 5 V | 6 | |
| Power Good threshold | VIT | 85 | 90 | 94 | %VOUT | VOUT decreasing | 6 |
| Power Good hysteresis | VHYS | 3 | %VOUT | 6 | |||
| Power Good low voltage | VPG-L | 0.3 | V | 7 | |||
| Power Good leakage | ILK | 0.1 | 1 | µA | VPG = 5.25 V, VOUT > VIT | 7 | |
| Thermal shutdown temperature | TSD | 165 | °C | High temperature threshold | 7 | ||
| Thermal shutdown hysteresis | TSD | 20 | °C | Thermal hysteresis | 7 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | the PCB copper area through the package leads. | 9 |
CAD (KiCad official)
- Symbol:
LD59150PUR - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: DFN10(3x3) (KiCad packages3D, STEP)
- 3D model files:
ld59150pur-etched.step/ld59150pur-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ld59150pur.step/ld59150pur.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (22 pp, sha256
fcfb83643350e4e1, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).