main
Download ZIP Propose a change
Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers ld59150pur: viewers · Ray
ld59150pur-etched.glb Publish 0.1.0 · Ray
ld59150pur-etched.step ld59150pur: factory component page (tier=mfr) · Ray
ld59150pur-hero.glb ld59150pur: hero GLB from the etched model (keeps the MPN mark) · Ray
ld59150pur-hero.overlay.json Publish 0.1.0 · Ray
ld59150pur.glb Publish 0.1.0 · Ray
ld59150pur.kicad_mod Publish 0.1.0 · Ray
ld59150pur.kicad_sym Publish 0.1.0 · Ray
ld59150pur.lbr Publish 0.1.0 · Ray
ld59150pur.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 11 pins · Ray

LD59150PUR

STMicroelectronics · Linear Voltage Regulators (LDO) · DFN10(3x3)

LD59150PUR from STMicroelectronics, in a DFN10(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Input supply pin for the LDO pass element, operating from 0.8 V to 5.5 V per the electrical characteristics.
2 VIN power_in Input supply pin (paired with pin 1) for the LDO pass element, operating from 0.8 V to 5.5 V per the electrical characteristics.
3 PG output Power Good open-drain flag that goes high impedance when VOUT exceeds VIT + VHYS and is pulled low when VOUT falls below VIT or the device is disabled; it needs an external pull-up of 10 kΩ to 1 MΩ to a potential below 5.5 V and sinks up to 1.5 mA.
4 VBIAS power_in Bias supply pin that must be supplied from 2.7 V to 5.5 V for the internal circuitry.
5 EN input Enable logic input where low (below 0.4 V) shuts the device down and high (above 1.1 V) activates it, and it must not be left floating.
6 GND power_in Ground reference pin to which all voltages are referred and which must also be connected to the exposed pad.
7 SS passive Soft-start pin where an external capacitor CSS sets the output ramp time by being charged with a constant 0.44 µA typical current.
8 FB input Feedback pin connected to the internal 0.8 V reference, used with an external resistor divider to set the output voltage from 0.8 V to 3.6 V.
9 VOUT power_out Regulated output pin delivering up to 1.5 A, with DC output voltage limited to -0.3 V to VIN + 0.3 V.
10 VOUT power_out Regulated output pin (paired with pin 9) delivering up to 1.5 A, with DC output voltage limited to -0.3 V to VIN + 0.3 V.
11 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package DFN10(3x3)
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Bias pin voltage VBIAS 2.7 5.5 V 6
Input voltage absolute maximum VIN -0.3 6 V Input voltage pin 5
Bias supply absolute maximum VBIAS -0.3 6 V Bias supply pin 5
Enable input voltage absolute maximum VEN -0.3 6 V Enable input voltage 5
Adjustable pin voltage absolute maximum VADJ -0.3 6 V Adjustable pin voltage 5
Soft-start pin voltage absolute maximum VSS -0.3 6 V Soft-start pin 5
Power Good pin voltage absolute maximum VPG -0.3 6 V Power Good pin 5
Power Good sink current IPG 0 1.5 mA Power Good sink current 5
Storage temperature range TST -55 150 °C 5
Operating junction temperature range TJ -40 150 °C 5
Thermal resistance junction-ambient RthJA 47.5 °C/W 4 layer JEDEC PCB (2S2P) test board with thermal vias 5
Thermal resistance junction-case RthJC 8 °C/W 4 layer JEDEC PCB (2S2P) test board with thermal vias 5
Reference voltage VREF 0.796 0.8 0.804 V T = + 25 °C 6
Output voltage accuracy VOUT -2 0.5 2 % 50 mA < IOUT < 1.5 A, 2.97 V < VBIAS < 5.5 V 6
VIN dropout voltage Vdrop 65 125 mV IOUT = 1.5 A, VBIAS - VOUT > 3.25 V 6
VBIAS dropout voltage Vdrop 0.92 1.1 V IOUT = 1.5 A VIN = VBIAS 6
Current limit Icl 2 3 5.5 A VOUT = 80% x VOUT(nom) 6
Bias pin current IBIAS 0.88 1.5 mA 6
Shutdown supply current ISHDN 1 50 µA VEN < 0.4 V (measured through GND) 6
Feedback pin current IFB -1 0.001 1 µA 6
Line regulation 0.01 %/V VOUT(nom) + 0.3 V < VIN < 5.5 V 6
Load regulation 0.02 %/A 50 mA < IOUT < 1.5 A 6
Soft-start charging current ISS 0.44 µA VSS = 0.4 V 6
Minimum start-up time Tstr 100 µs IOUT = 1 A, CSS = floating 6
Enable input high VEN-H 1.1 5.5 V 6
Enable input low VEN-L 0 0.4 V 6
Enable hysteresis VEN-Hyst 50 mV 6
Enable deglitch time TDG 20 µs 6
Enable pin current IEN 0.1 1 µA VEN = 5 V 6
Power Good threshold VIT 85 90 94 %VOUT VOUT decreasing 6
Power Good hysteresis VHYS 3 %VOUT 6
Power Good low voltage VPG-L 0.3 V 7
Power Good leakage ILK 0.1 1 µA VPG = 5.25 V, VOUT > VIT 7
Thermal shutdown temperature TSD 165 °C High temperature threshold 7
Thermal shutdown hysteresis TSD 20 °C Thermal hysteresis 7

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper the PCB copper area through the package leads. 9

CAD (KiCad official)

  • Symbol: LD59150PUR
  • Footprint: Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm
  • 3D model: DFN10(3x3) (KiCad packages3D, STEP)
  • 3D model files: ld59150pur-etched.step / ld59150pur-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ld59150pur.step / ld59150pur.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (22 pp, sha256 fcfb83643350e4e1, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF