Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT8714EFE#PBF

Analog Devices · DC-DC Controllers · TSSOP-20-EP

LT8714EFE#PBF from Analog Devices, in a TSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 FB input Feedback input; a resistor from FB to VOUT is set by RFB = 7250Ω • (VOUT - VCTRL)/(VCTRL - 0.6065).
2 VC output Error amplifier output that requires an external compensation network.
3 SS passive Soft-start pin charged through an internal 260k resistor to about 2.7V; its capacitor must be at least 5× the IMON capacitor.
4 PG output Active-high open-drain power good output that needs a pull-up; power is good when VFB is within ±60mV of VCTRL, with PG voltage limited to -0.3V to 7V and PG current to ±1mA.
5 IMON output Output current monitor with VIMON = 12.14 • (VISP - VISN + 49.9mV) that must be filtered by 10nF to 100nF and must not be resistively loaded.
6 ISN input Kelvin-connected output current sense negative input that limits the sense voltage across the sense resistor to 50mV typical; voltage range up to 80V.
7 ISP input Kelvin-connected output current sense positive input; ISP voltage is limited to ISN - 0.4V to ISN + 2V.
8 BIAS power_in Top gate driver supply connected to the input supply VIN and locally bypassed; rated to 80V.
9 INTVEE power_out Regulator output at 6.18V below BIAS (typical) that needs a minimum 2.2µF bypass to BIAS and sets the bottom rail of the TG driver.
10 TG output PFET gate drive with low level BIAS - INTVEE and high level BIAS.
11 BG output NFET gate drive with low level GND and high level INTVCC.
12 INTVCC power_out 6.3V input LDO regulator output that needs a minimum 2.2µF bypass to GND and allows a maximum 5mA external load.
13 VIN power_in Input supply pin with a minimum operating voltage of 4.5V (typical) and an absolute maximum of 80V.
14 CSN input NFET current sense negative input; the negative sense voltage at low duty cycle is -32mV (typical).
15 CSP input NFET current sense positive input; the maximum positive sense voltage at low duty cycle is 66mV (typical).
16 EN input Enable input that shuts the chip down below 0.3V and activates it above 1.3V (typical); it must not float and is rated to 80V.
17 CTRL input Output voltage control input that accepts 0.1V to 1.1V; FB regulates to about 1.213V if CTRL exceeds 1.213V and to about 0V if CTRL is below 0V.
18 RT passive Timing resistor pin that sets the switching frequency between 100kHz and 750kHz; it must not float.
19 SYNC input Synchronization input whose high level must be between 1.5V and 5V and whose low level must be below 0.4V.
20 GND power_in Ground pin that must be soldered directly to the local ground plane.
21 GND power_in Exposed pad is GND and must be soldered to the PCB.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package TSSOP-20-EP
Category Power Supply Chip
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Absolute maximum VIN voltage VIN -0.3 80 V 2
Absolute maximum BIAS voltage BIAS -0.3 80 V 2
Absolute maximum EN voltage EN -0.3 80 V 2
Absolute maximum RT voltage RT -0.3 5 V 2
Absolute maximum SS voltage SS -0.3 3 V 2
Absolute maximum FB voltage FB -0.3 5 V 2
Absolute maximum VC voltage VC -0.3 2 V 2
Absolute maximum SYNC voltage SYNC -0.3 5.5 V 2
Absolute maximum PG voltage PG -0.3 7 V 2
Absolute maximum PG current PG -1 1 mA 2
Absolute maximum CTRL voltage CTRL -0.3 5 V 2
Absolute maximum INTVCC voltage INTVCC -0.3 7 V 2
Absolute maximum CSP voltage CSP -0.3 2 V 2
Absolute maximum CSN voltage CSN -0.3 2 V 2
Absolute maximum ISN voltage ISN -0.3 80 V 2
Absolute maximum IMON voltage IMON -0.3 2.5 V 2
Storage temperature range -65 150 °C 2
Operating junction temperature range LT8714E -40 125 °C LT8714E 2
Maximum junction temperature TJMAX 125 °C 2
Junction-to-ambient thermal resistance θJA 38 °C/W 2
Junction-to-case thermal resistance θJC 10 °C/W 2
Minimum Operating Input Voltage VIN 4.25 4.5 V 3
Quiescent Current IVIN 4 5.5 mA Not Switching, VBIAS = 7.5V 3
Quiescent Current in Shutdown 0 1 µA VEN = 0V 3
EN Chip Enable Threshold EN Rising 1.22 1.3 1.38 V 3
EN Chip Enable Threshold EN Falling 1.18 1.26 1.34 V 3
EN Input Voltage Low Shutdown Mode 0.3 V 3
SS Charge Current 7 10.1 13.8 µA VSS = 50mV, Current Flowing Out of SS pin 3
SS Low Detection Voltage 18 50 82 mV Part Exiting Undervoltage Lockout 3
SS Voltage to Enable Switching SS Rising 0.75 1 1.21 V 3
SS Voltage to Enable Switching SS Falling 0.65 0.92 1.15 V 3
INTVCC Voltage 6.2 6.3 6.4 V IINTVCC = 10mA 3
INTVCC Undervoltage Lockout Rising 3.88 4 4.12 V INTVCC Rising 3
INTVCC Undervoltage Lockout Falling 3.5 3.73 3.95 V INTVCC Falling 3
INTVCC Load Regulation -0.44 -2 % VIN = 12V, IINTVCC = 0mA to 80mA 3
INTVCC Line Regulation -0.005 -0.03 %/V 10V ≤ VIN ≤ 80V, IINTVCC = 10mA 3
INTVCC Maximum External Load Current 5 mA 3
INTVEE Voltage, VBIAS, VINTVEE 6.03 6.18 6.33 V IINTVEE = 10mA 3
INTVEE Undervoltage Lockout Rising 3.24 3.42 3.6 V VBIAS, VINTVEE Rising 3
INTVEE Undervoltage Lockout Falling 2.94 3.22 3.48 V VBIAS, VINTVEE Falling 3
IINTVEE Dropout Voltage VINTVEE 0.75 V VBIAS = 6V, IINTVEE = 10mA 3
Current Limit Voltage, Minimum Duty Cycle VCSP, VCSN 60.5 66 71.5 mV VFB = 1.4V, CTRL = 1.1V, Minimum Duty Cycle 3
Current Limit Voltage, Maximum Duty Cycle VCSP, VCSN 40 47 56 mV VFB = 1.4V, CTRL = 1.1V, Maximum Duty Cycle 3
FB Regulation Voltage 1.092 1.102 1.112 V CTRL = 1.1V 3
FB Regulation Voltage 0.092 0.102 0.112 V CTRL = 0.1V 3
FB Regulation Voltage 0 0.0167 0.033 V CTRL = 0V 3
FB Internal Voltage, V1 V1 0.597 0.6065 0.616 V IFB = 0.0μA 4
FB Internal Resistance, R1 R1 7.1 7.25 7.4 kΩ 4
Output Current Sense Regulation Voltage, VISP, VISN VISP, VISN 46 50 54 mV VISN = 80V, VFB = 1.4V, CTRL = 1.1V 4
IMON Regulation Voltage, EA2 EA2 1.184 1.208 1.233 V VFB = 1V 4
Switching Frequency, fOSC fOSC 640 750 860 kHz RT = 46.4k 4
Switching Frequency, fOSC fOSC 85 100 115 kHz RT = 357k 4
Switching Frequency Range 100 750 kHz Free-Running or Synchronizing 4
SYNC High Level for Sync 1.5 V 4
SYNC Low Level for Sync 0.4 V 4
SYNC Clock Pulse Duty Cycle 20 80 % VSYNC = 0V to 3V 4
BG and TG Non-Overlap Time, TG Rising to BG Rising 80 140 220 ns CBG = CTG = 3300pF 4
BG and TG Non-Overlap Time, BG Falling to TG Falling 45 90 150 ns CBG = CTG = 3300pF 4
PG Overvoltage Threshold, VFB, CTRL, VFB Rising 75 114 155 mV 0.1V ≤ CTRL ≤ 1.1V 5
PG Undervoltage Threshold, VFB, CTRL, VFB Rising -100 -60 -20 mV 0.1V ≤ CTRL ≤ 1.1V 5

CAD (KiCad official)

  • Symbol: LT8714EFE#PBF
  • Footprint: Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm
  • 3D model: TSSOP-20-EP (KiCad packages3D, STEP)
  • 3D model files: lt8714efe-pbf-etched.step / lt8714efe-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8714efe-pbf.step / lt8714efe-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (36 pp, sha256 7b11b2ddef6206c9, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF