3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownSI5338A-B-GM
Skyworks Solutions · Clock / Timing - Application Specific · QFN-24(4x4)
SI5338A-B-GM from Skyworks Solutions, in a QFN-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN1 | input | CLKIN: main differential clock input (with IN2) or XTAL input, must be ac-coupled; leave unconnected when not in use. |
| 2 | IN2 | input | CLKINB: complementary differential clock input or XTAL input, must be ac-coupled; connect to GND when not in use. |
| 3 | IN3 | input | CLKIN on the Si5338A/B/C: high-impedance dc-coupled single-ended clock input; connect to ground if not used. |
| 4 | IN4 | input | I2C_LSB on the Si5338A/B/C: LSB of the I2C address (0 = 70h, 1 = 71h). |
| 5 | IN5 | input | FDBK: differential feedback input for zero delay mode or secondary clock input, must be ac-coupled; leave unconnected when not in use. |
| 6 | IN6 | input | FDBKB: complementary differential feedback input or secondary clock input, must be ac-coupled; connect to GND when not in use. |
| 7 | VDD | power_in | Core supply voltage of 1.8, 2.5, or 3.3 V, with a 0.1 µF bypass capacitor very close to the pin. |
| 8 | INTR | output | Open-drain interrupt output needing a typical 1-4 kΩ pullup, which can go to a supply as high as 3.6 V. |
| 9 | CLK3B | output | Output clock B for channel 3, single-ended or the other half of a differential pair with CLK3A; leave floating if unused. |
| 10 | CLK3A | output | Output clock A for channel 3, single-ended or the other half of a differential pair with CLK3B; leave floating if unused. |
| 11 | VDDO3 | power_in | Output supply (3.3, 2.5, 1.8, or 1.5 V) for CLK3A,B with a 0.1 µF capacitor close to the pin; tie to VDD if CLK3 is unused. |
| 12 | SCL | input | I2C serial clock input, requires a 1-4 kΩ typical pullup and is 3.3 V tolerant regardless of other supply voltages. |
| 13 | CLK2B | output | Output clock B for channel 2, single-ended or the other half of a differential pair with CLK2A; leave floating if unused. |
| 14 | CLK2A | output | Output clock A for channel 2, single-ended or the other half of a differential pair with CLK2B; leave floating if unused. |
| 15 | VDDO2 | power_in | Output supply (3.3, 2.5, 1.8, or 1.5 V) for CLK2A,B with a 0.1 µF capacitor close to the pin; tie to VDD if CLK2 is unused. |
| 16 | VDDO1 | power_in | Output supply (3.3, 2.5, 1.8, or 1.5 V) for CLK1A,B with a 0.1 µF capacitor close to the pin; tie to VDD if CLK1 is unused. |
| 17 | CLK1B | output | Output clock B for channel 1, single-ended or the other half of a differential pair with CLK1A; leave floating if unused. |
| 18 | CLK1A | output | Output clock A for channel 1, single-ended or the other half of a differential pair with CLK1B; leave floating if unused. |
| 19 | SDA | bidirectional | I2C serial data, requires a 1-4 kΩ typical pullup and is 3.3 V tolerant regardless of other supply voltages. |
| 20 | VDDO0 | power_in | Output supply (3.3, 2.5, 1.8, or 1.5 V) for CLK0A,B with a 0.1 µF capacitor close to the pin; tie to VDD if CLK0 is unused. |
| 21 | CLK0B | output | Output clock B for channel 0, single-ended or the other half of a differential pair with CLK0A; leave floating if unused. |
| 22 | CLK0A | output | Output clock A for channel 0, single-ended or the other half of a differential pair with CLK0B; leave floating if unused. |
| 23 | RSVD_GND | power_in | Ground pin that must be connected to system ground with minimal ground path impedance. |
| 24 | VDD | power_in | Core supply voltage of 1.8, 2.5, or 3.3 V, with a 0.1 µF bypass capacitor very close to the pin. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Skyworks Solutions |
| Package | QFN-24(4x4) |
| Category | RTC/Clock Chip |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Ambient Temperature | TA | -40 | 25 | 85 | °C | 4 | |
| Core Supply Voltage | VDD | 2.97 | 3.3 | 3.63 | V | VDD 3.3 V ±10% | 4 |
| Core Supply Voltage | VDD | 2.25 | 2.5 | 2.75 | V | VDD 2.5 V ±10% | 4 |
| Core Supply Voltage | VDD | 1.71 | 1.8 | 1.98 | V | VDD 1.8 V -5% to +10% | 4 |
| Output Buffer Supply Voltage | VDDOn | 1.4 | 3.63 | V | 4 | ||
| DC Supply Voltage | VDD | -0.5 | 3.8 | V | 4 | ||
| Storage Temperature Range | TSTG | -55 | 150 | °C | 4 | ||
| Junction Temperature | TJ | 150 | °C | 4 | |||
| Peak Soldering Reflow Temperature | 260 | °C | JEDEC J-STD-020 | 4 | |||
| Thermal Resistance Junction to Ambient | JA | 37 | °C/W | Still Air | 5 | ||
| Core Supply Current | IDD | 45 | 60 | mA | 100 MHz on all outputs, 25 MHz refclk | 5 | |
| Output Buffer Supply Current LVPECL | IDDOx | 30 | mA | LVPECL, 710 MHz | 5 | ||
| Output Buffer Supply Current LVDS | IDDOx | 8 | mA | LVDS, 710 MHz | 5 | ||
| Output Buffer Supply Current HCSL | IDDOx | 20 | mA | HCSL, 250 MHz, 2 pF load | 5 | ||
| Output Buffer Supply Current SSTL | IDDOx | 19 | mA | SSTL, 350 MHz | 5 | ||
| Output Buffer Supply Current CMOS 50 MHz | IDDOx | 6 | 9 | mA | CMOS, 50 MHz, 15 pF load | 5 | |
| Output Buffer Supply Current CMOS 200 MHz 3.3 V | IDDOx | 13 | 18 | mA | CMOS, 200 MHz, 3.3 V VDD0 | 5 | |
| Output Buffer Supply Current HSTL | IDDOx | 19 | mA | HSTL, 350 MHz | 5 | ||
| PLL Acquisition Time | tACQ | 25 | ms | 6 | |||
| PLL Tracking Range | fTRACK | 5000 | 20000 | ppm | 6 | ||
| MultiSynth Frequency Synthesis Resolution | fRES | 0 | 0 | 1 | ppb | Output frequency < Fvco/8 | 6 |
| CLKIN Loss of Signal Detect Time | tLOS | 2.6 | 5 | µs | 6 | ||
| PLL Loss of Lock Detect Time | tLOL | 5 | 10 | ms | 6 | ||
| POR to Output Clock Valid | tRDY | 2 | ms | Pre-programmed Devices | 6 | ||
| Input-to-Output Propagation Delay | tPROP | 2.5 | 4 | ns | Buffer Mode (PLL Bypass) | 6 | |
| POR to I2C Ready | 15 | ms | 6 | ||||
| Programmable Initial Phase Offset | POFFSET | -45 | 45 | ns | 6 | ||
| Phase Increment/Decrement Range | PRANGE | -45 | 45 | ns | 6 | ||
| MultiSynth range for phase increment/decrement | fPRANGE | 5 | MHz | Maximum printed as Fvco/8 | 6 | ||
| Frequency Increment/Decrement Step Size | fSTEP | 1 | ppm | R divider not used; maximum see Note 2 | 7 | ||
| Spread Spectrum PP Frequency Deviation | SSDEV | 0.1 | 5.04 | % | MultiSynth Output < ~Fvco/8 | 7 | |
| Spread Spectrum Modulation Rate | SSDEV | 30 | 635 | kHz | MultiSynth Output < ~Fvco/8 | 7 | |
| Input Clock Frequency (AC coupled differential) | fIN | 5 | 710 | MHz | Pins IN1/2, IN5/6 | 8 | |
| Differential Voltage Swing | VPP | 0.4 | 2.4 | VPP | 710 MHz input | 8 | |
| Rise/Fall Time (differential input) | tR/tF | 1 | ns | 20%-80% | 8 | ||
| Duty Cycle (differential input) | DC | 40 | 60 | % | DC < 1 ns tr/tf | 8 | |
| Duty Cycle (PLL bypass) | DC | 45 | 55 | % | DC < 1 ns tr/tf (PLL bypass) | 8 | |
| Input Clock Frequency (DC coupled CMOS) | fIN | 5 | 200 | MHz | CMOS, pins IN3/4 | 8 | |
| Input Voltage | VI | -0.1 | 3.73 | V | 8 | ||
| Rise/Fall Time (single-ended input) | tR/tF | 4 | ns | 10%-90% | 8 | ||
| Rise/Fall Time (single-ended input) | tR/tF | 2.3 | ns | 20%-80% | 8 | ||
| Output Frequency LVPECL, LVDS, CML | fOUT | 0.16 | 350 | MHz | LVPECL, LVDS, CML | 8 | |
| Output Frequency (Fvco/4) | fOUT | 367 | 473.33 | MHz | LVPECL, LVDS, CML | 8 | |
| Output Frequency (Fvco/6) | fOUT | 550 | 710 | MHz | LVPECL, LVDS, CML | 8 | |
| Output Frequency HCSL | fOUT | 0.16 | 250 | MHz | HCSL | 8 | |
| LVPECL Peak-to-Peak Single-Ended Swing | VSEPP | 0.55 | 0.8 | 0.96 | VPP | LVPECL | 9 |
| LVDS Common Mode Voltage (2.5/3.3 V) | VOC | 1.125 | 1.2 | 1.275 | V | LVDS (2.5/3.3 V) | 9 |
| LVDS Peak-to-Peak Single-Ended Swing (2.5/3.3 V) | VSEPP | 0.25 | 0.35 | 0.45 | VPP | LVDS (2.5/3.3 V) | 9 |
| HCSL Common Mode Voltage | VOC | 0.35 | 0.375 | 0.4 | V | HCSL | 9 |
| HCSL Peak-to-Peak Single-Ended Swing | VSEPP | 0.575 | 0.725 | 0.85 | VPP | HCSL | 9 |
| CML Peak-to-Peak Single-Ended Swing | VSEPP | 0.67 | 0.86 | 1.07 | VPP | CML | 9 |
| Differential Output Rise/Fall Time | tR/tF | 450 | ps | 20%-80% | 9 | ||
| Differential Output Duty Cycle | DC | 45 | 55 | % | Not in PLL bypass mode | 9 | |
| Output Frequency CMOS | fOUT | 0.16 | 200 | MHz | CMOS | 9 | |
| Output Frequency SSTL, HSTL | fOUT | 0.16 | 350 | MHz | SSTL, HSTL | 9 | |
| CMOS Output Rise/Fall Time | tR/tF | 0.45 | 0.85 | ns | 20%-80%, 2 pF load | 9 | |
| CMOS Output Voltage Low | VOL | 0.3 | V | 4 mA load | 10 | ||
| Single-Ended Output Duty Cycle | DC | 45 | 55 | % | Not in PLL bypass mode | 10 | |
| Input Voltage Low (IN3, IN4) | VIL | -0.1 | 0.3 | V | 0.3 x VDD | 11 | |
| Input Voltage High (IN3, IN4) | VIH | 0.7 | 3.73 | V | 0.7 x VDD minimum | 11 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | PC | 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body | 39 |
CAD (KiCad official)
- Symbol:
SI5338A-B-GM - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: QFN-24(4x4) (KiCad packages3D, STEP)
- 3D model files:
si5338a-b-gm-etched.step/si5338a-b-gm-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);si5338a-b-gm.step/si5338a-b-gm.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Skyworks Solutions datasheet (46 pp, sha256
d6857f2e224a5271, retrieved 2026-11-07, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).