3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownIKCM10L60GA
Infineon Technologies · Intelligent Power Modules (IPM) · DIP-24
IKCM10L60GA from Infineon Technologies, in a DIP-24. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VS(U) | power_in | U-phase high side floating IC supply offset voltage, robust against -50V transient negative voltage with respect to VSS. |
| 2 | VB(U) | power_in | U-phase high side floating IC supply voltage, supplied by integrated bootstrap circuit with VBS recommended 13.5V to 18.5V. |
| 3 | VS(V) | power_in | V-phase high side floating IC supply offset voltage, robust against -50V transient negative voltage with respect to VSS. |
| 4 | VB(V) | power_in | V-phase high side floating IC supply voltage, supplied by integrated bootstrap circuit with VBS recommended 13.5V to 18.5V. |
| 5 | VS(W) | power_in | W-phase high side floating IC supply offset voltage, robust against -50V transient negative voltage with respect to VSS. |
| 6 | VB(W) | power_in | W-phase high side floating IC supply voltage, supplied by integrated bootstrap circuit with VBS recommended 13.5V to 18.5V. |
| 7 | HIN(U) | input | U-phase high side gate driver input, positive logic, Schmitt-trigger with internal ~5k pull-down, LSTTL/CMOS compatible down to 3.3V. |
| 8 | HIN(V) | input | V-phase high side gate driver input, positive logic, Schmitt-trigger with internal ~5k pull-down, LSTTL/CMOS compatible down to 3.3V. |
| 9 | HIN(W) | input | W-phase high side gate driver input, positive logic, Schmitt-trigger with internal ~5k pull-down, LSTTL/CMOS compatible down to 3.3V. |
| 10 | LIN(U) | input | U-phase low side gate driver input, positive logic, Schmitt-trigger with internal ~5k pull-down, input pulse width not recommended below 1µs. |
| 11 | LIN(V) | input | V-phase low side gate driver input, positive logic, Schmitt-trigger with internal ~5k pull-down, input pulse width not recommended below 1µs. |
| 12 | LIN(W) | input | W-phase low side gate driver input, positive logic, Schmitt-trigger with internal ~5k pull-down, input pulse width not recommended below 1µs. |
| 13 | VDD | power_in | Low side control supply powering input logic and output stage, recommended 14.0V to 18.5V (typ 16V), UV lockout at typ 10.4V falling. |
| 14 | VFO | bidirectional | Open-drain fault output indicating VDD undervoltage or ITRIP overcurrent, also gives direct access to the NTC thermistor referenced to VSS, requires external pull-up. |
| 15 | ITRIP | input | Over current shutdown input with typ 0.47V comparator threshold referenced to VSS, typ 530ns noise filter, shuts down all outputs. |
| 16 | VSS | power_in | Low side control negative supply and ground reference for input logic, VSS to N within ±5V including surge. |
| 17 | NW | passive | W-phase low side IGBT emitter (open emitter) available for phase current measurement, keep connection to VSS short. |
| 18 | NV | passive | V-phase low side IGBT emitter (open emitter) available for phase current measurement, keep connection to VSS short. |
| 19 | NU | passive | U-phase low side IGBT emitter (open emitter) available for phase current measurement, keep connection to VSS short. |
| 20 | W | passive | Motor W-phase output, high side emitter and low side collector. |
| 21 | V | power_in | Motor V-phase output, high side emitter and low side collector. |
| 22 | U | passive | Motor U-phase output, high side emitter and low side collector. |
| 23 | P | power_in | Positive bus input voltage connected to high side IGBTs, bus voltage must not exceed 450V. |
| 24 | NC | unconnected | No connection. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Infineon Technologies |
| Package | DIP-24 |
| Category | Triode/MOS Tube/Transistor |
| Pins | 24 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage temperature range | Tstg | -40 | 125 | °C | 7 | ||
| Isolation test voltage | VISOL | 2000 | V | RMS, f = 60Hz, t = 1min | 7 | ||
| Operating case temperature range | TC | -40 | 125 | °C | Refer to Figure 6 | 7 | |
| Max. blocking voltage | VCES | 600 | V | IC = 250µA | 7 | ||
| DC link supply voltage of P-N | VPN | 450 | V | Applied between P-N | 7 | ||
| DC link supply voltage (surge) of P-N | VPN(surge) | 500 | V | Applied between P-N | 7 | ||
| Output current | IC | -10 | 10 | A | TC = 25°C, TJ < 150°C | 7 | |
| Output current | IC | -6 | 6 | A | TC = 80°C, TJ < 150°C | 7 | |
| Maximum peak output current | IC(peak) | -20 | 20 | A | less than 1ms | 7 | |
| Short circuit withstand time | tSC | 5 | µs | VDC ≤ 400V, TJ = 150°C | 7 | ||
| Power dissipation per IGBT | Ptot | 25.2 | W | 7 | |||
| Operating junction temperature range | TJ | -40 | 150 | °C | 7 | ||
| Single IGBT thermal resistance, junction-case | RthJC | 4.96 | K/W | 7 | |||
| Single diode thermal resistance, junction-case | RthJCD | 6.88 | K/W | 7 | |||
| Module supply voltage | VDD | -1 | 20 | V | 7 | ||
| High side floating supply voltage (VB vs. VS) | VBS | -1 | 20 | V | 7 | ||
| Input voltage LIN, HIN | VIN | -1 | 10 | V | 7 | ||
| Input voltage ITRIP | VITRIP | -1 | 10 | V | 7 | ||
| Switching frequency | fPWM | 20 | kHz | 7 | |||
| DC link supply voltage of P-N | VPN | 0 | 400 | V | 8 | ||
| High side floating supply voltage (VB vs. VS) | VBS | 13.5 | 18.5 | V | 8 | ||
| Low side supply voltage | VDD | 14 | 16 | 18.5 | V | 8 | |
| Control supply variation | ΔVBS, ΔVDD | -1 | 1 | V/µs | 8 | ||
| Logic input voltages LIN, HIN | VIN | 0 | 5 | V | 8 | ||
| Logic input voltage ITRIP | VITRIP | 0 | 5 | V | 8 | ||
| Between VSS - N (including surge) | VSS | -5 | 5 | V | 8 | ||
| Collector-Emitter saturation voltage | VCE(sat) | 1.55 | 2.05 | V | IC = 6A, TJ = 25°C | 9 | |
| Collector-Emitter saturation voltage | VCE(sat) | 1.85 | V | IC = 6A, TJ = 150°C | 9 | ||
| Diode forward voltage | VF | 1.75 | 2.5 | V | IF= 6A, TJ = 25°C | 9 | |
| Diode forward voltage | VF | 1.78 | V | IF= 6A, TJ = 150°C | 9 | ||
| Collector-Emitter leakage current | ICES | 1 | mA | VCE = 600V | 9 | ||
| Logic "1" input voltage (LIN, HIN) | VIH | 2.1 | 2.5 | V | 9 | ||
| Logic "0" input voltage (LIN, HIN) | VIL | 0.7 | 0.9 | V | 9 | ||
| ITRIP positive going threshold | VIT,TH+ | 400 | 470 | 540 | mV | 9 | |
| ITRIP input hysteresis | VIT,HYS | 40 | 70 | mV | 9 | ||
| VDD and VBS supply under voltage positive going threshold | VDDUV+, VBSUV+ | 10.8 | 12.1 | 13 | V | 9 | |
| VDD and VBS supply under voltage negative going threshold | VDDUV-, VBSUV- | 9.5 | 10.4 | 11.2 | V | 9 | |
| VDD and VBS supply under voltage lockout hysteresis | VDDUVH, VBSUVH | 1 | 1.7 | V | 9 | ||
| Input clamp voltage (HIN, LIN, ITRIP) | VINCLAMP | 9 | 10.1 | 12.5 | V | Iin=4mA | 9 |
| Quiescent VBx supply current | IQBS | 300 | 500 | µA | VBx only, HIN = 0V | 9 | |
| Quiescent VDD supply current | IQDD | 370 | 900 | µA | VDD only, LIN = 0V, HINX = 5V | 9 | |
| Input bias current | IIN+ | 1 | 1.5 | mA | VIN = 5V | 9 | |
| ITRIP input bias current | IITRIP+ | 65 | 150 | µA | VITRIP = 5V | 9 | |
| Fault clear time after ITRIP-fault | tFLTCLR | 40 | 65 | 200 | µs | VITRIP = 1V | 10 |
| Deadtime between low side and high side | DTPWM | 1 | µs | 10 | |||
| Repetitive peak reverse voltage | VRRM | 600 | V | 10 | |||
| Mounting torque | 0.59 | 0.69 | 0.78 | Nm | M3 screw and washer | 11 | |
| Flatness | -50 | 100 | µm | Refer to Figure 8 | 11 | ||
| Input bias current | IIN- | 2 | µA | VIN = 0V | 9 | ||
| VFO input bias current | IFO | 60 | µA | VFO = 5V, VITRIP = 0V | 9 | ||
| VFO output voltage | VFO | 0.5 | V | IFO = 10mA, VITRIP = 1V | 9 | ||
| Thermistor resistance | RNTC | 85 | kΩ | TNTC = 25°C | 11 | ||
| B-constant of NTC | B(25/100) | 4092 | K | 11 |
CAD (KiCad official)
- Symbol:
IKCM10L60GA - Footprint:
Package_DIP:DIP-24_W7.62mm - 3D model: DIP-24 (KiCad packages3D, STEP)
- 3D model files:
ikcm10l60ga-etched.step/ikcm10l60ga-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ikcm10l60ga.step/ikcm10l60ga.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Infineon Technologies datasheet (17 pp, sha256
1b145c0a67eb3494, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).