Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LTC1060CN#PBF

Analog Devices · Switched Capacitor Filters · PDIP-20

LTC1060CN#PBF from Analog Devices, in a PDIP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 LPA output Lowpass output of filter block A, one of the two switched-capacitor filter outputs.
2 BPA output Bandpass output of filter block A; wideband noise at the BP and LP outputs increases for high Q values.
3 N/AP/HPA output Notch, allpass or highpass output of filter block A, depending on the configured filter function.
4 INVA input Inverting input of the input op amp of filter block A.
5 S1A input Voltage signal input of filter A that should be driven from a source impedance below 5kΩ; tie to AGND when not used.
6 SA/B input When high, the S2 summer input is tied to the lowpass output; when connected to the negative supply, S2 switches to ground and becomes inactive.
7 VA+ power_in Positive analog supply pin, biased from the same DC source as VD+ and typically bypassed with a 0.1µF ceramic capacitor; the filter operates reliably from a ±2.37V minimum supply.
8 VD+ power_in Positive digital supply pin, normally tied to VA+ and bypassed with a 0.1µF ceramic capacitor.
9 LSh input Level shift pin for T2L or CMOS clock levels; connect to ground (AGND potential) for dual supplies of ±4.5V or higher.
10 CLKA input Clock input for filter A, sharing the LSh level shift; the duty cycle should be close to 50%.
11 CLKB input Clock input for filter B, sharing the LSh level shift; the duty cycle should be close to 50%.
12 50/100/HOLD input Mode pin: tied to V+ selects 50:1 operation, tied to 1/2 supply (AGND) selects 100:1 operation, and shorting it to the negative supply stops the filter and holds the last sample.
13 VD- power_in Negative digital supply pin, normally tied to VA- and bypassed with a 0.1µF ceramic capacitor.
14 VA- power_in Negative analog supply pin, biased from the same DC source as VD-; the device operates from ±2.37V to ±8V supplies.
15 AGND power_in Analog ground: the system ground for dual supply operation, or the 1/2 supply point bypassed with 0.1µF for single supply operation.
16 S1B input Voltage signal input of filter B that should be driven from a source impedance below 5kΩ; tie to AGND when not used.
17 INVB input Inverting input of the input op amp of filter block B.
18 N/AP/HPB output Notch, allpass or highpass output of filter block B, depending on the configured filter function.
19 BPB output Bandpass output of filter block B; wideband noise at the BP and LP outputs increases for high Q values.
20 LPB output Lowpass output of filter block B; wideband noise at the BP and LP outputs increases for high Q values.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package PDIP-20
Category Filters
Pins 20

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Center Frequency Range (f0*Q <= 400kHz) f0 0.1 20 kHz f0*Q <= 400kHz, Mode 1, Figure 4; Vs = ±5V 2
Center Frequency Range (f0*Q <= 1.6MHz) f0 0.1 16 kHz f0*Q <= 1.6MHz, Mode 1, Figure 4; Vs = ±5V 2
Clock-to-Center Frequency Ratio tolerance (nominal 50:1) -0.8 0.8 % Mode 1, 50:1, fCLK = 250kHz, Q = 10; over full operating temperature range; Vs = ±5V 2
Clock-to-Center Frequency Ratio tolerance (nominal 100:1) -0.8 0.8 % Mode 1, 100:1, fCLK = 500kHz, Q = 10; over full operating temperature range; Vs = ±5V 2
Q Accuracy 0.5 5 % Mode 1, 50:1 or 100:1, f0 = 5kHz, Q = 10; over full operating temperature range; Vs = ±5V 2
DC Offset VOS1 VOS1 2 15 mV Over full operating temperature range; Vs = ±5V 2
DC Offset VOS2 (SA/B High) VOS2 3 40 mV fCLK = 250kHz, 50:1, SA/B = High; over full operating temperature range; Vs = ±5V 2
DC Offset VOS2 (SA/B High) VOS2 6 80 mV fCLK = 500kHz, 100:1, SA/B = High; over full operating temperature range; Vs = ±5V 2
DC Offset VOS2 (SA/B Low) VOS2 2 30 mV fCLK = 250kHz, 50:1, SA/B = Low; over full operating temperature range; Vs = ±5V 2
DC Offset VOS2 (SA/B Low) VOS2 4 60 mV fCLK = 500kHz, 100:1, SA/B = Low; over full operating temperature range; Vs = ±5V 2
DC Offset VOS3 VOS3 2 30 mV fCLK = 250kHz, 50:1, SA/B = Low; over full operating temperature range; Vs = ±5V 2
DC Offset VOS3 VOS3 4 60 mV fCLK = 500kHz, 100:1, SA/B = Low; over full operating temperature range; Vs = ±5V 2
DC Lowpass Gain Accuracy 0.1 2 % Mode 1, R1 = R2 = 50k; Vs = ±5V 2
BP Gain Accuracy at f0 -0.1 0.1 % Mode 1, Q = 10, f0 = 5kHz; Vs = ±5V 2
Power Supply Current 3 5 8 mA Vs = ±5V 2
Power Supply Current (over temperature) 12 mA Over full operating temperature range; Vs = ±5V 2
Supply Voltage Range 2.37 8 V Dual supply ±2.37V to ±8V 3
Voltage Swing (RL = 5k, Pins 1,2,19,20) 3.8 4 V Vs = ±5V, RL = 5k (Pins 1,2,19,20) 3
Voltage Swing (RL = 3.5k, Pins 3,18) 3.6 4 V RL = 3.5k (Pins 3,18); over full operating temperature range 3
Output Short-Circuit Current (Source) 25 mA Vs = ±5V 3
Output Short-Circuit Current (Sink) 3 mA Vs = ±5V 3
Op Amp GBW Product 2 MHz Vs = ±5V 3
Op Amp Slew Rate 7 V/µs Vs = ±5V 3
Op Amp DC Open Loop Gain 85 dB RL = 10k, Vs = ±5V 3
Clock Feedthrough 10 mV(P-P) fCLK ≤ 1MHz 2
Max Clock Frequency (Vs = ±5V) 1.5 MHz Vs = ±5V 2
Crosstalk 70 dB Vs = ±5V 2
Center Frequency Range (f0*Q <= 100kHz) f0 0.1 10 kHz f0*Q <= 100kHz; Vs = ±2.37V 3
Clock-to-Center Frequency Ratio tolerance (nominal 50:1) -0.8 0.8 % Mode 1, 50:1, fCLK = 250kHz, Q = 10; Vs = ±2.37V 3
Clock-to-Center Frequency Ratio tolerance (nominal 100:1) -0.8 0.8 % Mode 1, 100:1, fCLK = 250kHz, Q = 10; Vs = ±2.37V 3
Q Accuracy (f0 = 2.5kHz) -4 4 % Mode 1, 50:1 or 100:1, f0 = 2.5kHz, Q = 10; Vs = ±2.37V 3
Max Clock Frequency (Vs = ±2.37V) 500 kHz Vs = ±2.37V 3
Power Supply Current 2.5 4 mA Vs = ±2.37V 3
Supply Voltage 18 V 2
Power Dissipation 500 mW 2
Operating Temperature Range TA -40 85 °C LTC1060AC/LTC1060C 2
Storage Temperature Range -65 150 °C 2
Lead Temperature (Soldering, 10 sec) 300 °C Soldering, 10 sec 2
Short-Circuit Current 80 mA Above ±5V and at elevated temperatures (continuous short to negative supply) 9
Maximum Junction Temperature (N package) TJMAX 100 °C N package (LTC1060CN) 2
Thermal Resistance Junction-to-Ambient (N package) θJA 100 °C/W N package (LTC1060CN) 2

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE OR TIN PLATE LEADS 20

CAD (KiCad official)

  • Symbol: LTC1060CN#PBF
  • Footprint: Package_DIP:DIP-20_W7.62mm
  • 3D model: PDIP-20 (KiCad packages3D, STEP)
  • 3D model files: ltc1060cn-pbf-etched.step / ltc1060cn-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ltc1060cn-pbf.step / ltc1060cn-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (20 pp, sha256 f60a2048d02258bc, retrieved 2026-10-16, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF