3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownLTC1060CN#PBF
Analog Devices · Switched Capacitor Filters · PDIP-20
LTC1060CN#PBF from Analog Devices, in a PDIP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | LPA | output | Lowpass output of filter block A, one of the two switched-capacitor filter outputs. |
| 2 | BPA | output | Bandpass output of filter block A; wideband noise at the BP and LP outputs increases for high Q values. |
| 3 | N/AP/HPA | output | Notch, allpass or highpass output of filter block A, depending on the configured filter function. |
| 4 | INVA | input | Inverting input of the input op amp of filter block A. |
| 5 | S1A | input | Voltage signal input of filter A that should be driven from a source impedance below 5kΩ; tie to AGND when not used. |
| 6 | SA/B | input | When high, the S2 summer input is tied to the lowpass output; when connected to the negative supply, S2 switches to ground and becomes inactive. |
| 7 | VA+ | power_in | Positive analog supply pin, biased from the same DC source as VD+ and typically bypassed with a 0.1µF ceramic capacitor; the filter operates reliably from a ±2.37V minimum supply. |
| 8 | VD+ | power_in | Positive digital supply pin, normally tied to VA+ and bypassed with a 0.1µF ceramic capacitor. |
| 9 | LSh | input | Level shift pin for T2L or CMOS clock levels; connect to ground (AGND potential) for dual supplies of ±4.5V or higher. |
| 10 | CLKA | input | Clock input for filter A, sharing the LSh level shift; the duty cycle should be close to 50%. |
| 11 | CLKB | input | Clock input for filter B, sharing the LSh level shift; the duty cycle should be close to 50%. |
| 12 | 50/100/HOLD | input | Mode pin: tied to V+ selects 50:1 operation, tied to 1/2 supply (AGND) selects 100:1 operation, and shorting it to the negative supply stops the filter and holds the last sample. |
| 13 | VD- | power_in | Negative digital supply pin, normally tied to VA- and bypassed with a 0.1µF ceramic capacitor. |
| 14 | VA- | power_in | Negative analog supply pin, biased from the same DC source as VD-; the device operates from ±2.37V to ±8V supplies. |
| 15 | AGND | power_in | Analog ground: the system ground for dual supply operation, or the 1/2 supply point bypassed with 0.1µF for single supply operation. |
| 16 | S1B | input | Voltage signal input of filter B that should be driven from a source impedance below 5kΩ; tie to AGND when not used. |
| 17 | INVB | input | Inverting input of the input op amp of filter block B. |
| 18 | N/AP/HPB | output | Notch, allpass or highpass output of filter block B, depending on the configured filter function. |
| 19 | BPB | output | Bandpass output of filter block B; wideband noise at the BP and LP outputs increases for high Q values. |
| 20 | LPB | output | Lowpass output of filter block B; wideband noise at the BP and LP outputs increases for high Q values. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | PDIP-20 |
| Category | Filters |
| Pins | 20 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Center Frequency Range (f0*Q <= 400kHz) | f0 | 0.1 | 20 | kHz | f0*Q <= 400kHz, Mode 1, Figure 4; Vs = ±5V | 2 | |
| Center Frequency Range (f0*Q <= 1.6MHz) | f0 | 0.1 | 16 | kHz | f0*Q <= 1.6MHz, Mode 1, Figure 4; Vs = ±5V | 2 | |
| Clock-to-Center Frequency Ratio tolerance (nominal 50:1) | -0.8 | 0.8 | % | Mode 1, 50:1, fCLK = 250kHz, Q = 10; over full operating temperature range; Vs = ±5V | 2 | ||
| Clock-to-Center Frequency Ratio tolerance (nominal 100:1) | -0.8 | 0.8 | % | Mode 1, 100:1, fCLK = 500kHz, Q = 10; over full operating temperature range; Vs = ±5V | 2 | ||
| Q Accuracy | 0.5 | 5 | % | Mode 1, 50:1 or 100:1, f0 = 5kHz, Q = 10; over full operating temperature range; Vs = ±5V | 2 | ||
| DC Offset VOS1 | VOS1 | 2 | 15 | mV | Over full operating temperature range; Vs = ±5V | 2 | |
| DC Offset VOS2 (SA/B High) | VOS2 | 3 | 40 | mV | fCLK = 250kHz, 50:1, SA/B = High; over full operating temperature range; Vs = ±5V | 2 | |
| DC Offset VOS2 (SA/B High) | VOS2 | 6 | 80 | mV | fCLK = 500kHz, 100:1, SA/B = High; over full operating temperature range; Vs = ±5V | 2 | |
| DC Offset VOS2 (SA/B Low) | VOS2 | 2 | 30 | mV | fCLK = 250kHz, 50:1, SA/B = Low; over full operating temperature range; Vs = ±5V | 2 | |
| DC Offset VOS2 (SA/B Low) | VOS2 | 4 | 60 | mV | fCLK = 500kHz, 100:1, SA/B = Low; over full operating temperature range; Vs = ±5V | 2 | |
| DC Offset VOS3 | VOS3 | 2 | 30 | mV | fCLK = 250kHz, 50:1, SA/B = Low; over full operating temperature range; Vs = ±5V | 2 | |
| DC Offset VOS3 | VOS3 | 4 | 60 | mV | fCLK = 500kHz, 100:1, SA/B = Low; over full operating temperature range; Vs = ±5V | 2 | |
| DC Lowpass Gain Accuracy | 0.1 | 2 | % | Mode 1, R1 = R2 = 50k; Vs = ±5V | 2 | ||
| BP Gain Accuracy at f0 | -0.1 | 0.1 | % | Mode 1, Q = 10, f0 = 5kHz; Vs = ±5V | 2 | ||
| Power Supply Current | 3 | 5 | 8 | mA | Vs = ±5V | 2 | |
| Power Supply Current (over temperature) | 12 | mA | Over full operating temperature range; Vs = ±5V | 2 | |||
| Supply Voltage Range | 2.37 | 8 | V | Dual supply ±2.37V to ±8V | 3 | ||
| Voltage Swing (RL = 5k, Pins 1,2,19,20) | 3.8 | 4 | V | Vs = ±5V, RL = 5k (Pins 1,2,19,20) | 3 | ||
| Voltage Swing (RL = 3.5k, Pins 3,18) | 3.6 | 4 | V | RL = 3.5k (Pins 3,18); over full operating temperature range | 3 | ||
| Output Short-Circuit Current (Source) | 25 | mA | Vs = ±5V | 3 | |||
| Output Short-Circuit Current (Sink) | 3 | mA | Vs = ±5V | 3 | |||
| Op Amp GBW Product | 2 | MHz | Vs = ±5V | 3 | |||
| Op Amp Slew Rate | 7 | V/µs | Vs = ±5V | 3 | |||
| Op Amp DC Open Loop Gain | 85 | dB | RL = 10k, Vs = ±5V | 3 | |||
| Clock Feedthrough | 10 | mV(P-P) | fCLK ≤ 1MHz | 2 | |||
| Max Clock Frequency (Vs = ±5V) | 1.5 | MHz | Vs = ±5V | 2 | |||
| Crosstalk | 70 | dB | Vs = ±5V | 2 | |||
| Center Frequency Range (f0*Q <= 100kHz) | f0 | 0.1 | 10 | kHz | f0*Q <= 100kHz; Vs = ±2.37V | 3 | |
| Clock-to-Center Frequency Ratio tolerance (nominal 50:1) | -0.8 | 0.8 | % | Mode 1, 50:1, fCLK = 250kHz, Q = 10; Vs = ±2.37V | 3 | ||
| Clock-to-Center Frequency Ratio tolerance (nominal 100:1) | -0.8 | 0.8 | % | Mode 1, 100:1, fCLK = 250kHz, Q = 10; Vs = ±2.37V | 3 | ||
| Q Accuracy (f0 = 2.5kHz) | -4 | 4 | % | Mode 1, 50:1 or 100:1, f0 = 2.5kHz, Q = 10; Vs = ±2.37V | 3 | ||
| Max Clock Frequency (Vs = ±2.37V) | 500 | kHz | Vs = ±2.37V | 3 | |||
| Power Supply Current | 2.5 | 4 | mA | Vs = ±2.37V | 3 | ||
| Supply Voltage | 18 | V | 2 | ||||
| Power Dissipation | 500 | mW | 2 | ||||
| Operating Temperature Range | TA | -40 | 85 | °C | LTC1060AC/LTC1060C | 2 | |
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Lead Temperature (Soldering, 10 sec) | 300 | °C | Soldering, 10 sec | 2 | |||
| Short-Circuit Current | 80 | mA | Above ±5V and at elevated temperatures (continuous short to negative supply) | 9 | |||
| Maximum Junction Temperature (N package) | TJMAX | 100 | °C | N package (LTC1060CN) | 2 | ||
| Thermal Resistance Junction-to-Ambient (N package) | θJA | 100 | °C/W | N package (LTC1060CN) | 2 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE OR TIN PLATE LEADS | 20 |
CAD (KiCad official)
- Symbol:
LTC1060CN#PBF - Footprint:
Package_DIP:DIP-20_W7.62mm - 3D model: PDIP-20 (KiCad packages3D, STEP)
- 3D model files:
ltc1060cn-pbf-etched.step/ltc1060cn-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc1060cn-pbf.step/ltc1060cn-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (20 pp, sha256
f60a2048d02258bc, retrieved 2026-10-16, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).