Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

S25FL512SAGMFIR11

Cypress Semicon · Pre-ordered Products · SOIC-16

S25FL512SAGMFIR11 from Cypress Semicon, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 HOLD#/IO3 bidirectional HOLD# input pauses a command while low when Quad mode is not enabled (CR[1]=0), and the pin acts as I/O3 when Quad mode is enabled.
2 VCC power_in Core voltage supply for all internal logic, operating range 2.7 V to 3.6 V.
3 RESET# input Hardware reset input; driving it low for tRP time starts the hardware reset process (bonded out in this R model, RFU in other models).
4 DNU unconnected Do not use: internal test signal with an internal pull-down resistor, may be left unconnected or tied to VSS and must not be connected to any host signal.
5 DNU unconnected Do not use: internal test signal with an internal pull-down resistor, may be left unconnected or tied to VSS and must not be connected to any host signal.
6 RFU unconnected Reserved for future use: no internal signal is currently connected, and it is recommended not to use it for PCB routing.
7 CS# input Chip select input; the SPI interface is in standby when CS# is high and a command begins when it goes low.
8 SO/IO1 bidirectional Serial data output in single mode and I/O1 in dual and quad modes; high impedance during hold.
9 WP#/IO2 bidirectional Write protect input, relevant only during the instruction cycles of a WRR command, and I/O2 in quad mode.
10 VSS power_in Common ground reference for the device core, input receivers and output drivers.
11 DNU unconnected Do not use: internal test signal with an internal pull-down resistor, may be left unconnected or tied to VSS and must not be connected to any host signal.
12 DNU unconnected Do not use: internal test signal with an internal pull-down resistor, may be left unconnected or tied to VSS and must not be connected to any host signal.
13 NC unconnected Not connected: no internal signal is connected, and any signal connected to it must not exceed VIO.
14 VIO power_in Versatile I/O supply for all input receivers and output drivers, range 1.65 V to VCC and never greater than VCC (bonded out in this R model, RFU in other models).
15 SI/IO0 bidirectional Serial data input in single mode and I/O0 in dual and quad modes.
16 SCK input Serial clock input for SPI modes 0 and 3.

Key specifications

Parameter Value
Manufacturer Cypress Semicon
Package SOIC-16
Category Electronic Tools/Instruments/Consumables
Pins 16

CAD (KiCad official)

  • Symbol: S25FL512SAGMFIR11
  • Footprint: Package_SO:SOIC-16_3.9x9.9mm_P1.27mm
  • 3D model: SOIC-16 (KiCad packages3D, STEP)
  • 3D model files: s25fl512sagmfir11-etched.step / s25fl512sagmfir11-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); s25fl512sagmfir11.step / s25fl512sagmfir11.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Cypress Semicon datasheet (161 pp, sha256 d1b81b9155595e47, retrieved 2026-10-30, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF