3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownS25FL512SAGMFIR11
Cypress Semicon · Pre-ordered Products · SOIC-16
S25FL512SAGMFIR11 from Cypress Semicon, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | HOLD#/IO3 | bidirectional | HOLD# input pauses a command while low when Quad mode is not enabled (CR[1]=0), and the pin acts as I/O3 when Quad mode is enabled. |
| 2 | VCC | power_in | Core voltage supply for all internal logic, operating range 2.7 V to 3.6 V. |
| 3 | RESET# | input | Hardware reset input; driving it low for tRP time starts the hardware reset process (bonded out in this R model, RFU in other models). |
| 4 | DNU | unconnected | Do not use: internal test signal with an internal pull-down resistor, may be left unconnected or tied to VSS and must not be connected to any host signal. |
| 5 | DNU | unconnected | Do not use: internal test signal with an internal pull-down resistor, may be left unconnected or tied to VSS and must not be connected to any host signal. |
| 6 | RFU | unconnected | Reserved for future use: no internal signal is currently connected, and it is recommended not to use it for PCB routing. |
| 7 | CS# | input | Chip select input; the SPI interface is in standby when CS# is high and a command begins when it goes low. |
| 8 | SO/IO1 | bidirectional | Serial data output in single mode and I/O1 in dual and quad modes; high impedance during hold. |
| 9 | WP#/IO2 | bidirectional | Write protect input, relevant only during the instruction cycles of a WRR command, and I/O2 in quad mode. |
| 10 | VSS | power_in | Common ground reference for the device core, input receivers and output drivers. |
| 11 | DNU | unconnected | Do not use: internal test signal with an internal pull-down resistor, may be left unconnected or tied to VSS and must not be connected to any host signal. |
| 12 | DNU | unconnected | Do not use: internal test signal with an internal pull-down resistor, may be left unconnected or tied to VSS and must not be connected to any host signal. |
| 13 | NC | unconnected | Not connected: no internal signal is connected, and any signal connected to it must not exceed VIO. |
| 14 | VIO | power_in | Versatile I/O supply for all input receivers and output drivers, range 1.65 V to VCC and never greater than VCC (bonded out in this R model, RFU in other models). |
| 15 | SI/IO0 | bidirectional | Serial data input in single mode and I/O0 in dual and quad modes. |
| 16 | SCK | input | Serial clock input for SPI modes 0 and 3. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Cypress Semicon |
| Package | SOIC-16 |
| Category | Electronic Tools/Instruments/Consumables |
| Pins | 16 |
CAD (KiCad official)
- Symbol:
S25FL512SAGMFIR11 - Footprint:
Package_SO:SOIC-16_3.9x9.9mm_P1.27mm - 3D model: SOIC-16 (KiCad packages3D, STEP)
- 3D model files:
s25fl512sagmfir11-etched.step/s25fl512sagmfir11-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);s25fl512sagmfir11.step/s25fl512sagmfir11.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Cypress Semicon datasheet (161 pp, sha256
d1b81b9155595e47, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).