3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLTC2873CUFD#TRPBF
Analog Devices · RS232 ICs · WQFN-24-EP(4x5)
LTC2873CUFD#TRPBF from Analog Devices, in a WQFN-24-EP(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VEE | power_out | Generated negative supply (-6.3V) for the RS232 driver; tie pins 1, 10 and 25 together and connect a 1µF capacitor between VEE (pin 10) and GND. |
| 2 | RO | output | RS485 differential receiver output and RS232 receiver output, with logic levels referenced to GND and VL. |
| 3 | 485/232 | input | Interface select: a logic low enables RS232 mode and a logic high enables RS485 mode; do not float. |
| 4 | RE485 | input | RS485 receiver enable: a logic high disables the receiver (output Hi-Z) and a logic low enables it; no function in RS232 mode; do not float. |
| 5 | DE485/F232 | input | In RS485 mode a logic high enables the driver and a logic low sets its outputs Hi-Z; in RS232 mode a logic high selects Fast mode (up to 1Mbps) and a logic low selects Slow mode (up to 250kbps); do not float. |
| 6 | DI | input | RS485 and RS232 driver input, with logic levels referenced to GND and VL; do not float. |
| 7 | SHDN | input | Shutdown control: a logic low places the device in low-power shutdown independent of other inputs, with driver and receiver outputs Hi-Z; do not float. |
| 8 | GND | power_in | Ground; tie pins 8, 11, 16 and 20 together. |
| 9 | CAP | passive | Charge pump capacitor for the generated negative supply VEE; connect a 220nF capacitor between CAP and SW. |
| 10 | VEE | power_out | Generated negative supply (-6.3V) for the RS232 driver; tie to pins 1 and 25 and connect a 1µF capacitor from this pin to GND. |
| 11 | GND | power_in | Ground; tie together with pins 8, 16 and 20. |
| 12 | SW | passive | Switch pin for the boost regulator; connect a 10µH inductor between SW and VCC. |
| 13 | VDD | power_out | Generated positive supply (+7.0V) for the RS232 driver; connect a 1µF capacitor between VDD and GND. |
| 14 | VCC | power_in | Input supply (3V to 5.5V); tie pins 14, 18 and 21 together and connect a 2.2µF or larger capacitor between VCC (adjacent to VDD) and GND. |
| 15 | B/RI | bidirectional | RS485 negative receiver input and driver output; in RS232 mode this is the RS232 receiver input. |
| 16 | GND | power_in | Ground; tie together with pins 8, 11 and 20. |
| 17 | A/DO | bidirectional | RS485 positive receiver input and driver output; in RS232 mode this is the RS232 driver output. |
| 18 | VCC | power_in | Input supply (3V to 5.5V); tie together with pins 14 and 21. |
| 19 | NC | unconnected | Not connected internally. |
| 20 | GND | power_in | Ground; tie together with pins 8, 11 and 16. |
| 21 | VCC | power_in | Input supply (3V to 5.5V); tie together with pins 14 and 18. |
| 22 | VL | power_in | Logic supply (1.7V to 5.5V) for receiver outputs, driver inputs and control inputs; keep VL ≤ VCC for guaranteed specifications and bypass with 0.1µF to GND if not tied to VCC. |
| 23 | LB | input | Loopback enable: a logic high routes driver inputs internally to receiver outputs for self-test, and a logic low disables loopback; do not float. |
| 24 | TE485 | input | RS485 termination enable: a logic low connects the 120Ω resistor between A/DO and B/RI and a logic high leaves them unterminated; do not float. |
| 25 | VEE | power_out | Exposed pad, internally VEE (generated negative supply); must be soldered to the PCB to maintain low thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | WQFN-24-EP(4x5) |
| Category | Interface |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input supply voltage (VCC, VL) | VCC, VL | -0.3 | 7 | V | 2 | ||
| Generated positive supply | VDD | 7.5 | V | min printed as VCC, 0.3 V | 2 | ||
| Generated negative supply | VEE | -7.5 | 0.3 | V | 2 | ||
| Switch pin | SW | -0.3 | V | max printed as VDD + 0.3 V | 2 | ||
| Charge pump capacitor pin | CAP | 0.3 | V | min printed as VEE, 0.3 V | 2 | ||
| Interface pins voltage | A/DO, B/RI | -15 | 15 | V | 2 | ||
| Logic input pins voltage | DI, 485/232, DE485/F232, RE485, TE485, LB | -0.3 | 7 | V | 2 | ||
| SHDN and RO pins voltage | SHDN, RO | -0.3 | V | max printed as VL + 0.3 V | 2 | ||
| Differential terminator voltage (enabled) | A/DO to B/RI | -6 | 6 | V | Terminator enabled | 2 | |
| Differential terminator voltage (disabled) | A/DO to B/RI | -30 | 30 | V | Terminator disabled | 2 | |
| Operating temperature range | 0 | 70 | °C | LTC2873C grade | 2 | ||
| Storage temperature range | -65 | 150 | °C | 2 | |||
| Maximum junction temperature | TJMAX | 150 | °C | 2 | |||
| VCC supply voltage operating range | VCC | 3 | 5.5 | V | Full operating temperature range (l) | 3 | |
| VL logic supply operating range | VL | 1.7 | V | VL ≤ VCC; max printed as VCC | 3 | ||
| VCC supply current in shutdown mode | VCC | 8 | 30 | µA | SHDN = 0V; full operating temperature range (l) | 3 | |
| VCC supply current, RS232 or RS485 mode, driver and receiver enabled, termination disabled | VCC | 4 | 9 | mA | No load, SHDN = TE485 = DE485/F232 = VL, RE485 = 0; full operating temperature range (l) | 3 | |
| VCC supply current, RS485 mode with receiver and termination enabled, driver disabled | VCC | 4 | 9 | mA | No load, SHDN = 485/232 = VL, DE485/F232 = RE485 = TE485 = 0; full operating temperature range (l) | 3 | |
| VL supply current in any mode | VL | 0 | 5 | µA | No load; full operating temperature range (l) | 3 | |
| Maximum short-circuit current, RS485 driver | IOSD485 | -250 | 250 | mA | -7V ≤ VOUT ≤ 12V (Figure 2); printed ±250 mA | 3 | |
| RS485 receiver input current (A/DO, B/RI) | IIN485 | -100 | 125 | µA | (A/DO or B/RI) = 12V or -7V, VCC = 0V or 3.3V (Figure 3) | 3 | |
| Differential input signal threshold voltage (A/DO to B/RI) | -200 | 200 | mV | -7V ≤ (A/DO or B/RI) ≤ 12V; printed ±200 mV | 3 | ||
| Differential input failsafe rising threshold voltage | -200 | -70 | -20 | mV | -7V ≤ (A/DO or B/RI) ≤ 12V, (A/D0, B/RI) rising | 3 | |
| RS485 receiver output low voltage | VOL | 0.4 | V | Output low, I(RO) = 3mA (sinking), 3V ≤ VL ≤ 5.5V | 3 | ||
| Three-state (high impedance) output current, RO | -5 | 0 | 5 | µA | 0V ≤ RO ≤ VL, VL = 5.5V, RE485 = VL; printed 0 ±5 µA | 4 | |
| Short-circuit current, RO | -135 | 135 | mA | 0V ≤ RO ≤ VL, VL = 5.5V; printed ±135 mA | 4 | ||
| RS485 terminating resistor | RTERM | 108 | 120 | 156 | Ω | TE485 = 0V, VAB = 2V, VB = -7V, 0V, 10V (Figure 8) | 4 |
| RS232 driver output low voltage | VOLD | -5 | -5.5 | V | RL = 3kΩ, VEE ≤ -6V; max printed as VEE | 4 | |
| RS232 driver output high voltage | VOHD | 5 | 5.9 | V | RL = 3kΩ, VDD ≥ 6.5V; max printed as VDD | 4 | |
| RS232 receiver input threshold voltage | 0.6 | 1.5 | 2.5 | V | 4 | ||
| RS232 receiver input hysteresis | 0.1 | 0.4 | 1 | V | 4 | ||
| RS232 receiver output low voltage | VOL | 0.4 | V | I(RO) = 1mA (sinking), 1.7V ≤ VL < 5.5V | 4 | ||
| RS232 receiver input resistance | 3 | 5 | 7 | kΩ | -15V ≤ B/RI ≤ 15V, 485/232 = 0V | 4 | |
| RS485 maximum data rate | 20 | Mbps | Note 3; Figure 15 | 5 | |||
| RS485 driver propagation delay | tPLHD485, tPHLD485 | 20 | 70 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4) | 5 | |
| RS485 driver propagation delay difference | tPLHD485, tPHLD485 | -6 | 0 | 6 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4); printed 0 ±6 ns | 5 |
| RS485 driver skew (A/DO to B/RI) | tSKEWD485 | -8 | 0 | 8 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4); printed 0 ±8 ns | 5 |
| RS485 driver rise or fall time | tRD485, tFD485 | 7.5 | 12.5 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4) | 5 | |
| RS485 driver output enable or disable time | tZLD485, tZHD485, tLZD485, tHZD485 | 120 | ns | SHDN = VL, RL = 500Ω, CL = 50pF, DE485 ↑ and ↓ (Figure 5) | 5 | ||
| RS485 driver enable from shutdown time | tZHSD485, tZLSD485 | 4 | 12 | µs | DE485/F232 = VL, RL = 500Ω, CL = 50pF, SHDN ↑ (Figure 5) | 5 | |
| RS485 driver output disable into shutdown time | tHZSD485, tLZSD485 | 0.5 | 1 | µs | DE485/F232 = VL, RL = 500Ω, CL = 50pF, SHDN ↓ (Figure 5) | 5 | |
| RS485 receiver input to output time | tPLHR485, tPHLR485 | 45 | 85 | ns | CL = 15pF, VCM = 1.5V, /A/DO to B/RI/ = 1.5V, (Figure 6) | 5 | |
| Differential receiver skew | tSKEWR485 | -9 | 0 | 9 | ns | CL = 15pF (Figure 6); printed 0 ±9 ns | 5 |
| Receiver output rise or fall time | tRR485, tFR485 | 3 | 15 | ns | CL = 15pF (Figure 6) | 5 | |
| Receiver output enable or disable time | tZLR485, tZHR485, tLZR485, tHZR485 | 12 | 85 | ns | 485/232 = SHDN = VL, RL = 1kΩ, CL = 15pF, RE485 ↓ and ↑ (Figure 7) | 5 | |
| Receiver enable from shutdown time | tZHSR485, tZLSR485 | 4 | 12 | µs | 485/232 = VL, RE485 = 0V, RL = 1kΩ, CL = 15pF, SHDN ↑ (Figure 7) | 5 | |
| Receiver output disable into shutdown time | tHZSR485, tLZSR485 | 0.5 | 1 | µs | 485/232 = VL, RE485 = 0V, RL = 1kΩ, CL = 15pF, SHDN ↓ (Figure 7) | 5 | |
| RS232 driver propagation delay, slow mode | tPHLD232, tPLHD232 | 1.5 | 3 | µs | RL = 3kΩ, CL = 50pF (Slow Mode) | 5 | |
| RS232 driver propagation delay, fast mode | tPHLD232, tPLHD232 | 0.4 | 1 | µs | RL = 3kΩ, CL = 50pF (Fast Mode) | 5 | |
| RS232 driver skew, slow mode | tSKEWD232 | -400 | 0 | 400 | ns | RL = 3kΩ, CL = 50pF (Slow Mode); printed 0 ±400 ns | 5 |
| RS232 driver skew, fast mode | tSKEWD232 | -100 | 0 | 100 | ns | RL = 3kΩ, CL = 50pF (Fast Mode); printed 0 ±100 ns | 5 |
| RS232 driver enable from shutdown time | tZLSD232, tZHSD232 | 5 | 12 | µs | VDD = 7.0V, VEE = -6.3V, 485/232 = 0V, RL = 3kΩ, CL = 50pF, SHDN ↑ (Figure 10) | 5 | |
| RS232 driver output disable into shutdown time | tLZSD232, tHZSD232 | 0.6 | 2 | µs | 485/232 = 0V, RL = 3kΩ, CL = 50pF, SHDN ↓ (Figure 10) | 5 | |
| RS232 receiver propagation delay | tPHLR232, tPLHR232 | 60 | 200 | ns | CL = 150pF (Figure 11) | 5 | |
| RS232 receiver output rise or fall time | tRR232, tFR232 | 70 | 200 | ns | CL = 150pF (Figure 11) | 5 | |
| RS232 receiver enable from shutdown time | tZLSR232, tZHSR232 | 5 | 12 | µs | VDD = 7.0V, VEE = -6.3V, 485/232 = 0V, RL = 1kΩ, CL = 150pF, SHDN ↑ (Figure 12) | 6 | |
| RS232 receiver disable into shutdown time | tLZSR232, tHZSR232 | 0.4 | 2 | µs | 485/232 = 0V, RL = 1kΩ, CL = 150pF, SHDN ↓ (Figure 12) | 6 | |
| VDD and VEE supply rise time (shutdown to RS485 ready) | tRDY | 0.2 | 1 | ms | Figure 13 | 6 | |
| Thermal resistance, junction to ambient (UFD package) | θJA | 43 | °C/W | Printed with pin configuration; no test conditions given | 2 |
CAD (KiCad official)
- Symbol:
LTC2873CUFD#TRPBF - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x5mm_P0.5mm_EP2.65x3.65mm - 3D model: WQFN-24-EP(4x5) (KiCad packages3D, STEP)
- 3D model files:
ltc2873cufd-trpbf-etched.step/ltc2873cufd-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc2873cufd-trpbf.step/ltc2873cufd-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (32 pp, sha256
d40dfc07983a4caf, retrieved 2026-10-19, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).