main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers ltc2873cufd-trpbf: viewers · Ray
ltc2873cufd-trpbf-etched.glb Publish 0.1.0 · Ray
ltc2873cufd-trpbf-etched.step ltc2873cufd-trpbf: factory component page (tier=lcsc) · Ray
ltc2873cufd-trpbf-hero.glb ltc2873cufd-trpbf: hero GLB from the etched model (keeps the MPN mark) · Ray
ltc2873cufd-trpbf-hero.overlay.json Publish 0.1.0 · Ray
ltc2873cufd-trpbf.glb Publish 0.1.0 · Ray
ltc2873cufd-trpbf.kicad_mod Publish 0.1.0 · Ray
ltc2873cufd-trpbf.kicad_sym Publish 0.1.0 · Ray
ltc2873cufd-trpbf.lbr Publish 0.1.0 · Ray
ltc2873cufd-trpbf.step Publish 0.1.0 · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray

LTC2873CUFD#TRPBF

Analog Devices · RS232 ICs · WQFN-24-EP(4x5)

LTC2873CUFD#TRPBF from Analog Devices, in a WQFN-24-EP(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VEE power_out Generated negative supply (-6.3V) for the RS232 driver; tie pins 1, 10 and 25 together and connect a 1µF capacitor between VEE (pin 10) and GND.
2 RO output RS485 differential receiver output and RS232 receiver output, with logic levels referenced to GND and VL.
3 485/232 input Interface select: a logic low enables RS232 mode and a logic high enables RS485 mode; do not float.
4 RE485 input RS485 receiver enable: a logic high disables the receiver (output Hi-Z) and a logic low enables it; no function in RS232 mode; do not float.
5 DE485/F232 input In RS485 mode a logic high enables the driver and a logic low sets its outputs Hi-Z; in RS232 mode a logic high selects Fast mode (up to 1Mbps) and a logic low selects Slow mode (up to 250kbps); do not float.
6 DI input RS485 and RS232 driver input, with logic levels referenced to GND and VL; do not float.
7 SHDN input Shutdown control: a logic low places the device in low-power shutdown independent of other inputs, with driver and receiver outputs Hi-Z; do not float.
8 GND power_in Ground; tie pins 8, 11, 16 and 20 together.
9 CAP passive Charge pump capacitor for the generated negative supply VEE; connect a 220nF capacitor between CAP and SW.
10 VEE power_out Generated negative supply (-6.3V) for the RS232 driver; tie to pins 1 and 25 and connect a 1µF capacitor from this pin to GND.
11 GND power_in Ground; tie together with pins 8, 16 and 20.
12 SW passive Switch pin for the boost regulator; connect a 10µH inductor between SW and VCC.
13 VDD power_out Generated positive supply (+7.0V) for the RS232 driver; connect a 1µF capacitor between VDD and GND.
14 VCC power_in Input supply (3V to 5.5V); tie pins 14, 18 and 21 together and connect a 2.2µF or larger capacitor between VCC (adjacent to VDD) and GND.
15 B/RI bidirectional RS485 negative receiver input and driver output; in RS232 mode this is the RS232 receiver input.
16 GND power_in Ground; tie together with pins 8, 11 and 20.
17 A/DO bidirectional RS485 positive receiver input and driver output; in RS232 mode this is the RS232 driver output.
18 VCC power_in Input supply (3V to 5.5V); tie together with pins 14 and 21.
19 NC unconnected Not connected internally.
20 GND power_in Ground; tie together with pins 8, 11 and 16.
21 VCC power_in Input supply (3V to 5.5V); tie together with pins 14 and 18.
22 VL power_in Logic supply (1.7V to 5.5V) for receiver outputs, driver inputs and control inputs; keep VL ≤ VCC for guaranteed specifications and bypass with 0.1µF to GND if not tied to VCC.
23 LB input Loopback enable: a logic high routes driver inputs internally to receiver outputs for self-test, and a logic low disables loopback; do not float.
24 TE485 input RS485 termination enable: a logic low connects the 120Ω resistor between A/DO and B/RI and a logic high leaves them unterminated; do not float.
25 VEE power_out Exposed pad, internally VEE (generated negative supply); must be soldered to the PCB to maintain low thermal resistance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package WQFN-24-EP(4x5)
Category Interface
Pins 25

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input supply voltage (VCC, VL) VCC, VL -0.3 7 V 2
Generated positive supply VDD 7.5 V min printed as VCC, 0.3 V 2
Generated negative supply VEE -7.5 0.3 V 2
Switch pin SW -0.3 V max printed as VDD + 0.3 V 2
Charge pump capacitor pin CAP 0.3 V min printed as VEE, 0.3 V 2
Interface pins voltage A/DO, B/RI -15 15 V 2
Logic input pins voltage DI, 485/232, DE485/F232, RE485, TE485, LB -0.3 7 V 2
SHDN and RO pins voltage SHDN, RO -0.3 V max printed as VL + 0.3 V 2
Differential terminator voltage (enabled) A/DO to B/RI -6 6 V Terminator enabled 2
Differential terminator voltage (disabled) A/DO to B/RI -30 30 V Terminator disabled 2
Operating temperature range 0 70 °C LTC2873C grade 2
Storage temperature range -65 150 °C 2
Maximum junction temperature TJMAX 150 °C 2
VCC supply voltage operating range VCC 3 5.5 V Full operating temperature range (l) 3
VL logic supply operating range VL 1.7 V VL ≤ VCC; max printed as VCC 3
VCC supply current in shutdown mode VCC 8 30 µA SHDN = 0V; full operating temperature range (l) 3
VCC supply current, RS232 or RS485 mode, driver and receiver enabled, termination disabled VCC 4 9 mA No load, SHDN = TE485 = DE485/F232 = VL, RE485 = 0; full operating temperature range (l) 3
VCC supply current, RS485 mode with receiver and termination enabled, driver disabled VCC 4 9 mA No load, SHDN = 485/232 = VL, DE485/F232 = RE485 = TE485 = 0; full operating temperature range (l) 3
VL supply current in any mode VL 0 5 µA No load; full operating temperature range (l) 3
Maximum short-circuit current, RS485 driver IOSD485 -250 250 mA -7V ≤ VOUT ≤ 12V (Figure 2); printed ±250 mA 3
RS485 receiver input current (A/DO, B/RI) IIN485 -100 125 µA (A/DO or B/RI) = 12V or -7V, VCC = 0V or 3.3V (Figure 3) 3
Differential input signal threshold voltage (A/DO to B/RI) -200 200 mV -7V ≤ (A/DO or B/RI) ≤ 12V; printed ±200 mV 3
Differential input failsafe rising threshold voltage -200 -70 -20 mV -7V ≤ (A/DO or B/RI) ≤ 12V, (A/D0, B/RI) rising 3
RS485 receiver output low voltage VOL 0.4 V Output low, I(RO) = 3mA (sinking), 3V ≤ VL ≤ 5.5V 3
Three-state (high impedance) output current, RO -5 0 5 µA 0V ≤ RO ≤ VL, VL = 5.5V, RE485 = VL; printed 0 ±5 µA 4
Short-circuit current, RO -135 135 mA 0V ≤ RO ≤ VL, VL = 5.5V; printed ±135 mA 4
RS485 terminating resistor RTERM 108 120 156 Ω TE485 = 0V, VAB = 2V, VB = -7V, 0V, 10V (Figure 8) 4
RS232 driver output low voltage VOLD -5 -5.5 V RL = 3kΩ, VEE ≤ -6V; max printed as VEE 4
RS232 driver output high voltage VOHD 5 5.9 V RL = 3kΩ, VDD ≥ 6.5V; max printed as VDD 4
RS232 receiver input threshold voltage 0.6 1.5 2.5 V 4
RS232 receiver input hysteresis 0.1 0.4 1 V 4
RS232 receiver output low voltage VOL 0.4 V I(RO) = 1mA (sinking), 1.7V ≤ VL < 5.5V 4
RS232 receiver input resistance 3 5 7 kΩ -15V ≤ B/RI ≤ 15V, 485/232 = 0V 4
RS485 maximum data rate 20 Mbps Note 3; Figure 15 5
RS485 driver propagation delay tPLHD485, tPHLD485 20 70 ns RDIFF = 54Ω, CL = 100pF (Figure 4) 5
RS485 driver propagation delay difference tPLHD485, tPHLD485 -6 0 6 ns RDIFF = 54Ω, CL = 100pF (Figure 4); printed 0 ±6 ns 5
RS485 driver skew (A/DO to B/RI) tSKEWD485 -8 0 8 ns RDIFF = 54Ω, CL = 100pF (Figure 4); printed 0 ±8 ns 5
RS485 driver rise or fall time tRD485, tFD485 7.5 12.5 ns RDIFF = 54Ω, CL = 100pF (Figure 4) 5
RS485 driver output enable or disable time tZLD485, tZHD485, tLZD485, tHZD485 120 ns SHDN = VL, RL = 500Ω, CL = 50pF, DE485 ↑ and ↓ (Figure 5) 5
RS485 driver enable from shutdown time tZHSD485, tZLSD485 4 12 µs DE485/F232 = VL, RL = 500Ω, CL = 50pF, SHDN ↑ (Figure 5) 5
RS485 driver output disable into shutdown time tHZSD485, tLZSD485 0.5 1 µs DE485/F232 = VL, RL = 500Ω, CL = 50pF, SHDN ↓ (Figure 5) 5
RS485 receiver input to output time tPLHR485, tPHLR485 45 85 ns CL = 15pF, VCM = 1.5V, /A/DO to B/RI/ = 1.5V, (Figure 6) 5
Differential receiver skew tSKEWR485 -9 0 9 ns CL = 15pF (Figure 6); printed 0 ±9 ns 5
Receiver output rise or fall time tRR485, tFR485 3 15 ns CL = 15pF (Figure 6) 5
Receiver output enable or disable time tZLR485, tZHR485, tLZR485, tHZR485 12 85 ns 485/232 = SHDN = VL, RL = 1kΩ, CL = 15pF, RE485 ↓ and ↑ (Figure 7) 5
Receiver enable from shutdown time tZHSR485, tZLSR485 4 12 µs 485/232 = VL, RE485 = 0V, RL = 1kΩ, CL = 15pF, SHDN ↑ (Figure 7) 5
Receiver output disable into shutdown time tHZSR485, tLZSR485 0.5 1 µs 485/232 = VL, RE485 = 0V, RL = 1kΩ, CL = 15pF, SHDN ↓ (Figure 7) 5
RS232 driver propagation delay, slow mode tPHLD232, tPLHD232 1.5 3 µs RL = 3kΩ, CL = 50pF (Slow Mode) 5
RS232 driver propagation delay, fast mode tPHLD232, tPLHD232 0.4 1 µs RL = 3kΩ, CL = 50pF (Fast Mode) 5
RS232 driver skew, slow mode tSKEWD232 -400 0 400 ns RL = 3kΩ, CL = 50pF (Slow Mode); printed 0 ±400 ns 5
RS232 driver skew, fast mode tSKEWD232 -100 0 100 ns RL = 3kΩ, CL = 50pF (Fast Mode); printed 0 ±100 ns 5
RS232 driver enable from shutdown time tZLSD232, tZHSD232 5 12 µs VDD = 7.0V, VEE = -6.3V, 485/232 = 0V, RL = 3kΩ, CL = 50pF, SHDN ↑ (Figure 10) 5
RS232 driver output disable into shutdown time tLZSD232, tHZSD232 0.6 2 µs 485/232 = 0V, RL = 3kΩ, CL = 50pF, SHDN ↓ (Figure 10) 5
RS232 receiver propagation delay tPHLR232, tPLHR232 60 200 ns CL = 150pF (Figure 11) 5
RS232 receiver output rise or fall time tRR232, tFR232 70 200 ns CL = 150pF (Figure 11) 5
RS232 receiver enable from shutdown time tZLSR232, tZHSR232 5 12 µs VDD = 7.0V, VEE = -6.3V, 485/232 = 0V, RL = 1kΩ, CL = 150pF, SHDN ↑ (Figure 12) 6
RS232 receiver disable into shutdown time tLZSR232, tHZSR232 0.4 2 µs 485/232 = 0V, RL = 1kΩ, CL = 150pF, SHDN ↓ (Figure 12) 6
VDD and VEE supply rise time (shutdown to RS485 ready) tRDY 0.2 1 ms Figure 13 6
Thermal resistance, junction to ambient (UFD package) θJA 43 °C/W Printed with pin configuration; no test conditions given 2

CAD (KiCad official)

  • Symbol: LTC2873CUFD#TRPBF
  • Footprint: Package_DFN_QFN:QFN-24-1EP_4x5mm_P0.5mm_EP2.65x3.65mm
  • 3D model: WQFN-24-EP(4x5) (KiCad packages3D, STEP)
  • 3D model files: ltc2873cufd-trpbf-etched.step / ltc2873cufd-trpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ltc2873cufd-trpbf.step / ltc2873cufd-trpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (32 pp, sha256 d40dfc07983a4caf, retrieved 2026-10-19, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF