Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT3750AEMS#TRPBF

Analog Devices · Interface - Specialized · MSOP-10

LT3750AEMS#TRPBF from Analog Devices, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VTRANS power_in Transformer supply pin powering the primary coil and boundary mode detection circuitry; bypass at the pin with a 1µF to 10µF capacitor (absolute maximum 24V, minimum 2.5V to 3V).
2 DONE output Open-collector indication pin that turns on an NPN when the target output voltage is reached or on a fault such as thermal shutdown or undervoltage lockout; requires a pull-up resistor or current source (absolute maximum 24V, ±1mA).
3 CHARGE input Starts a charge cycle when driven to 1.1V or higher and disables charging below 0.2V, requiring a step input with a minimum ramp rate of 1V/µs; GATE drives low within 200ns of CHARGE falling below the 50mV dynamic threshold (absolute maximum 24V).
4 VCC power_in Input supply pin, minimum 3V, absolute maximum 24V; bypass locally with a 1µF to 10µF ceramic capacitor.
5 GND power_in Ground pin; connect directly to the local ground plane.
6 SOURCE input Senses NMOS drain current via the NMOS source and current sense resistor, with a current limit of 78mV/RSENSE (absolute maximum 1V).
7 GATE output Gate driver output for the external NMOS, driving the gate voltage to within VCC - 2V each switching cycle (absolute maximum 24V).
8 RDCM passive Discontinuous mode sense pin that detects when transformer current has decayed to zero and starts a new charge cycle; connect a resistor (43k, 5% recommended) to the NMOS drain (current into pin ±1mA).
9 RVOUT passive Output voltage VI converter pin that develops a current proportional to the output capacitor voltage; connect a resistor to the NMOS drain (current into pin ±1mA).
10 RBG input Output voltage sense pin that senses the voltage across the RBG resistor, disabling charging and pulling DONE low when it reaches 1.24V; connect a resistor of 2.5k or less (2.49k, 1% recommended) to GND (absolute maximum 1.5V).

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-10
Category Interface
Pins 10

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Minimum VCC 2.8 3 V full temperature range 2
Minimum VTRANS 2.5 3 V full temperature range 2
VCC Quiescent Current 1.6 2.5 mA Not Switching, CHARGE = 5V 2
VCC Quiescent Current (shutdown) 1 µA Not Switching, CHARGE = 0V 2
VTRANS Quiescent Current 140 250 µA Not Switching, CHARGE = 5V 2
VTRANS Quiescent Current (shutdown) 1 µA Not Switching, CHARGE = 0V 2
CHARGE Pin Enable Voltage 0.87 1.1 V full temperature range 2
CHARGE Pin Disable Voltage DC Threshold 0.2 0.6 V DC Threshold, full temperature range 2
CHARGE Pin Disable Voltage Dynamic Threshold 30 60 mV Dynamic Threshold (Note 3) 2
VOUT Comparator Trip Voltage 1.215 1.24 1.265 V Measured RBG Pin 2
RBG Pin Bias Current 70 500 nA RBG = 1.2V 2
DCM Comparator Trip Voltage 5 36 80 mV Measured as VDRAIN, VTRANS, RDCM = 43k (Note 4) 2
Current Limit Comparator Trip Voltage 68 78 88 mV 2
DONE Output Signal Low 0.1 0.2 V 100kΩ to 5V 2
DONE Pin Leakage Current 0.2 µA DONE = 2.5V 2
GATE High Voltage 3 3.8 4.5 V CGATE = 1nF, VCC = 5V 3
GATE High Voltage 22 22.6 23.5 V CGATE = 1nF, VCC = 24V 3
Supply/pin voltage (VCC, VTRANS, GATE, DONE, CHARGE) 24 V 2
RBG pin voltage RBG 1.5 V 2
SOURCE pin voltage SOURCE 1 V 2
Current into RDCM Pin -1 1 mA 2
Current into RVOUT Pin -1 1 mA 2
Current into DONE Pin -1 1 mA 2
Operating Temperature Range -40 85 °C Note 2 2
Storage Temperature Range -65 150 °C 2
Maximum junction temperature TJMAX 125 °C 2
Thermal resistance junction to ambient θJA 160 °C/W 10-lead MSOP 2
CHARGE Pin Current 24 µA CHARGE = 24V 2
CHARGE Pin Current 19 µA CHARGE = 5V 2
CHARGE Pin Current 1 µA CHARGE = 0V 2
Minimum CHARGE Pin Low Time 20 µs High→Low→High 2
NMOS Minimum On Time 0.6 µs 2
GATE Rise Time 50 ns 3
GATE Turn Off Propagation Delay 100 ns CGATE = 1nF 3

CAD (KiCad official)

  • Symbol: LT3750AEMS#TRPBF
  • Footprint: Package_SO:MSOP-10_3x3mm_P0.5mm
  • 3D model: MSOP-10 (KiCad packages3D, STEP)
  • 3D model files: lt3750aems-trpbf-etched.step / lt3750aems-trpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt3750aems-trpbf.step / lt3750aems-trpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (16 pp, sha256 dc1d5b7724dc0fae, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF