3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownLM536025QPWPTQ1
Texas Instruments · DC-DC Converters · HTSSOP-16-EP
LM536025QPWPTQ1 from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | power_out | Regulator switch node that connects to the power inductor; pins 1 and 2 must be connected directly together at the PCB. |
| 2 | SW | power_out | Regulator switch node that connects to the power inductor; pins 1 and 2 must be connected directly together at the PCB. |
| 3 | CBOOT | power_out | Bootstrap supply for the gate drivers, requiring a high quality 470 nF capacitor from this pin to SW. |
| 4 | VCC | power_out | Internal 3.15 V regulator output supplying internal control circuits; do not connect to external loads and connect a high quality 3.3 µF capacitor to GND. |
| 5 | BIAS | power_in | Input to the internal voltage regulator that connects to the output voltage point and must not be grounded; connect a high quality 0.1 µF capacitor to GND. |
| 6 | SYNC | input | Synchronization input that locks the switching frequency to the system clock; connect to GND when unused and do not float. |
| 7 | FPWM | input | Mode control input where High selects forced PWM and Low selects automatic PFM/PWM transition; do not float. |
| 8 | RESET | output | Open drain reset output that goes low on fault or when EN is low and needs a current limiting pull-up resistor to a suitable supply (RESET pin current limited to 1 mA). |
| 9 | FB | input | Feedback input connected to the output sense point for fixed 5 V and 3.3 V options or to the feedback divider tap for the ADJ option; do not float or ground. |
| 10 | AGND | power_in | Analog ground for the regulator and system to which all electrical parameters are referenced; connect to EP and PGND on the PCB. |
| 11 | EN | input | Enable input where High turns the regulator ON and Low turns it OFF; it can be connected directly to VIN and must not float. |
| 12 | VIN | power_in | Input supply to the regulator (3.9 V to 36 V recommended operating range) requiring a high quality bypass capacitor to PGND; connect pins 12 and 13 directly together. |
| 13 | VIN | power_in | Input supply to the regulator (3.9 V to 36 V recommended operating range) requiring a high quality bypass capacitor to PGND; connect pins 12 and 13 directly together. |
| 14 | N/C | unconnected | No connection to the device. |
| 15 | PGND | power_in | Power ground for the internal low-side MOSFET that connects to AGND and system ground; connect pins 15 and 16 directly together. |
| 16 | PGND | power_in | Power ground for the internal low-side MOSFET that connects to AGND and system ground; connect pins 15 and 16 directly together. |
| 17 | EP | power_in | Exposed die attach paddle that must connect to the ground plane for adequate heat sinking and noise reduction. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Initial reference voltage accuracy for 5 V and 3.3 V options | VFB | -1 | 1 | % | VIN = 3.8 V to 36 V, FPWM, TJ = 25°C | 6 | |
| Initial reference voltage accuracy for 5 V and 3.3 V options | VFB | -1.25 | 1.25 | % | VIN = 3.8 V to 36 V, FPWM | 6 | |
| Minimum input voltage to operate, rising | VIN-operate | 3.2 | 3.95 | V | Rising | 6 | |
| Minimum input voltage to operate, falling | VIN-operate | 2.9 | 3.55 | V | Falling | 6 | |
| Operating quiescent current | IQ | 8 | 13 | µA | VBIAS = 5 V, TJ = -40°C to 125°C; measured at VIN pin | 6 | |
| Current into the BIAS pin | IB | 47 | 78 | µA | VBIAS = 5 V, FPWM = 3.3 V | 6 | |
| RESET upper threshold voltage | VRESET | 105 | 107 | 110 | % of nominal Vout | Rising, % of nominal Vout | 6 |
| RESET lower threshold voltage | VRESET | 92 | 94 | 96.5 | % of nominal Vout | Falling, % of nominal Vout | 6 |
| Low level RESET pin output voltage | VOL | 0.4 | V | 50 µA pull-up to RESET pin, Vin = 1.5 V, EN = 0 V | 6 | ||
| Enable input threshold voltage | VEN | 1.7 | 2 | V | Rising | 6 | |
| Enable input threshold for full shutdown | VEN-off | 0.8 | V | EN input voltage required for complete shutdown of the regulator, falling | 6 | ||
| Logic input high level on FPWM and SYNC pins | VIH | 1.5 | V | 6 | |||
| Logic input low level on FPWM and SYNC pins | VIL | 0.4 | V | 6 | |||
| High side switch current limit | IHS | 2.4 | 4.4 | A | LM53602-Q1 | 6 | |
| Low side switch current limit | ILS | 2 | 2.4 | 2.8 | A | LM53602-Q1 | 7 |
| Power switch on-resistance, high side MOSFET | Rdson | 135 | 290 | mΩ | High side MOSFET resistance | 7 | |
| Power switch on-resistance, low side MOSFET | Rdson | 60 | 125 | mΩ | Low side MOSFET resistance | 7 | |
| Switching frequency | FSW | 1.85 | 2.1 | 2.35 | MHz | VIN = 3.8 V to 18 V | 7 |
| Synchronizing frequency range | FSYNC | 1.9 | 2.1 | 2.3 | MHz | 7 | |
| Internal VCC voltage | VCC | 3.15 | V | VBIAS = 3.3 V | 7 | ||
| Thermal shutdown threshold, rising | TSD | 162 | 178 | °C | Rising | 7 | |
| Minimum switch on-time | TON | 50 | 80 | ns | VIN = 20 V | 8 | |
| Minimum switch off-time | TOFF | 125 | 200 | ns | VIN = 3.8 V | 8 | |
| Delay time to RESET high signal | TRESET-act | 2 | 3 | 4 | ms | 8 | |
| Glitch filter time for RESET function | TRESET-filter | 12 | 25 | 45 | µs | 8 | |
| Soft-start time | TSS | 1 | 2 | 3 | ms | 8 | |
| Turn-on delay | TEN | 0.7 | 0.8 | ms | CVCC = 1 µF, Tj = 25 °C | 8 | |
| Short circuit wait time (hiccup time) | TW | 5.5 | ms | 8 | |||
| Input voltage | VIN | 3.9 | 36 | V | 5 | ||
| Output voltage, fixed 5 V | VOUT | 0 | 5 | V | Fixed 5 V | 5 | |
| Output voltage, fixed 3.3 V | VOUT | 0 | 3.3 | V | Fixed 3.3 V | 5 | |
| Output voltage adjustment range, ADJ | VOUT | 3.3 | 6 | V | ADJ | 5 | |
| Output current for LM53602-Q1 | IOUT | 0 | 2 | A | LM53602-Q1 | 5 | |
| RESET pin current | IRESET | 0 | 1 | mA | 5 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 5 | ||
| VIN to AGND, PGND | VIN | -0.3 | 40 | V | DC | 4 | |
| CBOOT to SW | VCBOOT | -0.3 | 3.6 | V | 4 | ||
| EN to AGND, PGND | VEN | -0.3 | 40 | V | 4 | ||
| BIAS to AGND, PGND | VBIAS | -0.3 | 16 | V | 4 | ||
| FB to AGND, PGND for fixed 5 V and 3.3 V | VFB | -0.3 | 16 | V | fixed 5 V and 3.3 V | 4 | |
| FB to AGND, PGND for ADJ | VFB | -0.3 | 5.5 | V | ADJ | 4 | |
| RESET to AGND, PGND | VRESET | -0.3 | 8 | V | 4 | ||
| SYNC, FPWM to AGND, PGND | VSYNC | -0.3 | 5.5 | V | 4 | ||
| VCC to AGND, PGND | VCC | -0.3 | 4.2 | V | 4 | ||
| RESET pin current | IRESET | -0.1 | 1.2 | mA | 4 | ||
| AGND to PGND | VAGND-PGND | -0.3 | 0.3 | V | 4 | ||
| Storage temperature | Tstg | -40 | 150 | °C | 4 | ||
| Junction-to-ambient thermal resistance | RθJA | 42.5 | °C/W | PWP (HTSSOP) 16 pins | 5 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 22.6 | °C/W | PWP (HTSSOP) 16 pins | 5 | ||
| Junction-to-board thermal resistance | RθJB | 16.2 | °C/W | PWP (HTSSOP) 16 pins | 5 | ||
| Junction-to-top characterization parameter | ψJT | 0.6 | °C/W | PWP (HTSSOP) 16 pins | 5 | ||
| Junction-to-board characterization parameter | ψJB | 16 | °C/W | PWP (HTSSOP) 16 pins | 5 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 1.1 | °C/W | PWP (HTSSOP) 16 pins | 5 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | 9. Keep switch area small. The copper area connecting the SW pin to the inductor should be kept as short | 30 |
CAD (KiCad official)
- Symbol:
LM536025QPWPTQ1 - Footprint:
Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm - 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lm536025qpwptq1-etched.step/lm536025qpwptq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm536025qpwptq1.step/lm536025qpwptq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (42 pp, sha256
30558a4547afecd5, retrieved 2026-11-05, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).