main
Download ZIP Propose a change
Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers lm536025qpwptq1: viewers · Ray
lm536025qpwptq1-etched.glb Publish 0.1.0 · Ray
lm536025qpwptq1-etched.step lm536025qpwptq1: factory component page (tier=mfr) · Ray
lm536025qpwptq1-hero.glb lm536025qpwptq1: hero GLB from the etched model (keeps the MPN mark) · Ray
lm536025qpwptq1-hero.overlay.json Publish 0.1.0 · Ray
lm536025qpwptq1.glb Publish 0.1.0 · Ray
lm536025qpwptq1.kicad_mod Publish 0.1.0 · Ray
lm536025qpwptq1.kicad_sym Publish 0.1.0 · Ray
lm536025qpwptq1.lbr Publish 0.1.0 · Ray
lm536025qpwptq1.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 17 pins · Ray

LM536025QPWPTQ1

Texas Instruments · DC-DC Converters · HTSSOP-16-EP

LM536025QPWPTQ1 from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SW power_out Regulator switch node that connects to the power inductor; pins 1 and 2 must be connected directly together at the PCB.
2 SW power_out Regulator switch node that connects to the power inductor; pins 1 and 2 must be connected directly together at the PCB.
3 CBOOT power_out Bootstrap supply for the gate drivers, requiring a high quality 470 nF capacitor from this pin to SW.
4 VCC power_out Internal 3.15 V regulator output supplying internal control circuits; do not connect to external loads and connect a high quality 3.3 µF capacitor to GND.
5 BIAS power_in Input to the internal voltage regulator that connects to the output voltage point and must not be grounded; connect a high quality 0.1 µF capacitor to GND.
6 SYNC input Synchronization input that locks the switching frequency to the system clock; connect to GND when unused and do not float.
7 FPWM input Mode control input where High selects forced PWM and Low selects automatic PFM/PWM transition; do not float.
8 RESET output Open drain reset output that goes low on fault or when EN is low and needs a current limiting pull-up resistor to a suitable supply (RESET pin current limited to 1 mA).
9 FB input Feedback input connected to the output sense point for fixed 5 V and 3.3 V options or to the feedback divider tap for the ADJ option; do not float or ground.
10 AGND power_in Analog ground for the regulator and system to which all electrical parameters are referenced; connect to EP and PGND on the PCB.
11 EN input Enable input where High turns the regulator ON and Low turns it OFF; it can be connected directly to VIN and must not float.
12 VIN power_in Input supply to the regulator (3.9 V to 36 V recommended operating range) requiring a high quality bypass capacitor to PGND; connect pins 12 and 13 directly together.
13 VIN power_in Input supply to the regulator (3.9 V to 36 V recommended operating range) requiring a high quality bypass capacitor to PGND; connect pins 12 and 13 directly together.
14 N/C unconnected No connection to the device.
15 PGND power_in Power ground for the internal low-side MOSFET that connects to AGND and system ground; connect pins 15 and 16 directly together.
16 PGND power_in Power ground for the internal low-side MOSFET that connects to AGND and system ground; connect pins 15 and 16 directly together.
17 EP power_in Exposed die attach paddle that must connect to the ground plane for adequate heat sinking and noise reduction.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-16-EP
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Initial reference voltage accuracy for 5 V and 3.3 V options VFB -1 1 % VIN = 3.8 V to 36 V, FPWM, TJ = 25°C 6
Initial reference voltage accuracy for 5 V and 3.3 V options VFB -1.25 1.25 % VIN = 3.8 V to 36 V, FPWM 6
Minimum input voltage to operate, rising VIN-operate 3.2 3.95 V Rising 6
Minimum input voltage to operate, falling VIN-operate 2.9 3.55 V Falling 6
Operating quiescent current IQ 8 13 µA VBIAS = 5 V, TJ = -40°C to 125°C; measured at VIN pin 6
Current into the BIAS pin IB 47 78 µA VBIAS = 5 V, FPWM = 3.3 V 6
RESET upper threshold voltage VRESET 105 107 110 % of nominal Vout Rising, % of nominal Vout 6
RESET lower threshold voltage VRESET 92 94 96.5 % of nominal Vout Falling, % of nominal Vout 6
Low level RESET pin output voltage VOL 0.4 V 50 µA pull-up to RESET pin, Vin = 1.5 V, EN = 0 V 6
Enable input threshold voltage VEN 1.7 2 V Rising 6
Enable input threshold for full shutdown VEN-off 0.8 V EN input voltage required for complete shutdown of the regulator, falling 6
Logic input high level on FPWM and SYNC pins VIH 1.5 V 6
Logic input low level on FPWM and SYNC pins VIL 0.4 V 6
High side switch current limit IHS 2.4 4.4 A LM53602-Q1 6
Low side switch current limit ILS 2 2.4 2.8 A LM53602-Q1 7
Power switch on-resistance, high side MOSFET Rdson 135 290 mΩ High side MOSFET resistance 7
Power switch on-resistance, low side MOSFET Rdson 60 125 mΩ Low side MOSFET resistance 7
Switching frequency FSW 1.85 2.1 2.35 MHz VIN = 3.8 V to 18 V 7
Synchronizing frequency range FSYNC 1.9 2.1 2.3 MHz 7
Internal VCC voltage VCC 3.15 V VBIAS = 3.3 V 7
Thermal shutdown threshold, rising TSD 162 178 °C Rising 7
Minimum switch on-time TON 50 80 ns VIN = 20 V 8
Minimum switch off-time TOFF 125 200 ns VIN = 3.8 V 8
Delay time to RESET high signal TRESET-act 2 3 4 ms 8
Glitch filter time for RESET function TRESET-filter 12 25 45 µs 8
Soft-start time TSS 1 2 3 ms 8
Turn-on delay TEN 0.7 0.8 ms CVCC = 1 µF, Tj = 25 °C 8
Short circuit wait time (hiccup time) TW 5.5 ms 8
Input voltage VIN 3.9 36 V 5
Output voltage, fixed 5 V VOUT 0 5 V Fixed 5 V 5
Output voltage, fixed 3.3 V VOUT 0 3.3 V Fixed 3.3 V 5
Output voltage adjustment range, ADJ VOUT 3.3 6 V ADJ 5
Output current for LM53602-Q1 IOUT 0 2 A LM53602-Q1 5
RESET pin current IRESET 0 1 mA 5
Operating junction temperature TJ -40 150 °C 5
VIN to AGND, PGND VIN -0.3 40 V DC 4
CBOOT to SW VCBOOT -0.3 3.6 V 4
EN to AGND, PGND VEN -0.3 40 V 4
BIAS to AGND, PGND VBIAS -0.3 16 V 4
FB to AGND, PGND for fixed 5 V and 3.3 V VFB -0.3 16 V fixed 5 V and 3.3 V 4
FB to AGND, PGND for ADJ VFB -0.3 5.5 V ADJ 4
RESET to AGND, PGND VRESET -0.3 8 V 4
SYNC, FPWM to AGND, PGND VSYNC -0.3 5.5 V 4
VCC to AGND, PGND VCC -0.3 4.2 V 4
RESET pin current IRESET -0.1 1.2 mA 4
AGND to PGND VAGND-PGND -0.3 0.3 V 4
Storage temperature Tstg -40 150 °C 4
Junction-to-ambient thermal resistance RθJA 42.5 °C/W PWP (HTSSOP) 16 pins 5
Junction-to-case (top) thermal resistance RθJC(top) 22.6 °C/W PWP (HTSSOP) 16 pins 5
Junction-to-board thermal resistance RθJB 16.2 °C/W PWP (HTSSOP) 16 pins 5
Junction-to-top characterization parameter ψJT 0.6 °C/W PWP (HTSSOP) 16 pins 5
Junction-to-board characterization parameter ψJB 16 °C/W PWP (HTSSOP) 16 pins 5
Junction-to-case (bottom) thermal resistance RθJC(bot) 1.1 °C/W PWP (HTSSOP) 16 pins 5

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper 9. Keep switch area small. The copper area connecting the SW pin to the inductor should be kept as short 30

CAD (KiCad official)

  • Symbol: LM536025QPWPTQ1
  • Footprint: Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm
  • 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: lm536025qpwptq1-etched.step / lm536025qpwptq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm536025qpwptq1.step / lm536025qpwptq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (42 pp, sha256 30558a4547afecd5, retrieved 2026-11-05, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF