3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownNIS5420MT4TXG
onsemi · Surge Suppressors · WDFN-10(3x3)
NIS5420MT4TXG from onsemi, in a WDFN-10(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Negative input voltage to the device, used as the internal reference for the IC. |
| 2 | dv/dt | passive | Controls the output voltage slew rate at turn-on with an internal capacitor giving about a 2 ms ramp; an external capacitor can lengthen the ramp, and the pin is left open if no extra delay is needed. |
| 3 | En/Flt | bidirectional | Tri-state bidirectional enable/fault pin that is pulled to ground by an open-drain or open-collector device to shut down the eFuse, reads about 1.4 V in thermal shutdown and about 3 V in normal operation, and must not be actively driven or loaded with a capacitor. |
| 4 | ILIM | passive | A resistor between this pin and the source pin sets the overload and short-circuit current limit levels. |
| 5 | NC | unconnected | No connection for the NIS5420MT4 (this pin is ISENSE only on the MT1, MT2, MT6, MT7 and MT8 variants). |
| 6 | Src | power_out | Source of the internal power FET and output terminal of the fuse. |
| 7 | Src | power_out | Source of the internal power FET and output terminal of the fuse. |
| 8 | Src | power_out | Source of the internal power FET and output terminal of the fuse. |
| 9 | Src | power_out | Source of the internal power FET and output terminal of the fuse. |
| 10 | Src | power_out | Source of the internal power FET and output terminal of the fuse. |
| 11 | VCC | power_in | Positive input voltage to the device on the belly pad, rated -0.6 to 18 V steady-state and -0.6 to 25 V for 100 ms transients. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | WDFN-10(3x3) |
| Category | TVS/Fuse/Board Level Protection |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Off State Output Voltage | Voff | 50 | mV | VCC = 18 Vdc, VGS = 0 Vdc | 4 | ||
| Continuous Current (TA = 25°C, 100 mm2 copper) | ID | 4.6 | A | TA = 25°C, 100 mm2 copper (Note 3) | 4 | ||
| Continuous Current (TA = 80°C, minimum copper) | ID | 3.5 | A | TA = 80°C, minimum copper | 4 | ||
| Shutdown Temperature | TSD | 150 | 175 | 200 | °C | Note 3 | 4 |
| Thermal Shutdown Response Time | TSDRes | 10 | 15 | 20 | s | 4 | |
| Output Clamping Voltage (NIS5420MT1, NIS5420MT4, NIS5420MT5, NIS5420MT6) | VClamp2 | 13.6 | 16 | V | NIS5420MT1, NIS5420MT4, NIS5420MT5, NIS5420MT6 | 4 | |
| Output Clamping Response Time | TClamp_Res | 10 | s | 4 | |||
| Undervoltage Lockout (NIS5420MT1, NIS5420MT3, NIS5420MT4, NIS5420MT5, NIS5420MT6) | VUVLO1 | 7.8 | 8.5 | 9.2 | V | NIS5420MT1, MT3, MT4, MT5, MT6 | 4 |
| Kelvin Short Circuit Current Limit | ILim-SS | 1.76 | 2.1 | 2.64 | A | RLimit = 20, Note 4 | 4 |
| Logic Level Low (Output Disabled) | Vin-low | 0.35 | 0.58 | 0.81 | V | 4 | |
| Logic Level Mid (Thermal Fault, Output Disabled) | Vin-mid | 0.82 | 1.4 | 1.95 | V | Thermal Fault, Output Disabled | 4 |
| Logic Level High (Output Enabled) | Vin-high | 1.96 | 2.6 | 3 | V | Output Enabled | 4 |
| High State Maximum Voltage | Vin-max | 2.51 | 4.6 | 5 | V | 4 | |
| Logic Low Sink Current | Iin-low | -15 | -25 | A | Venable = 0 V | 4 | |
| Logic High Leakage Current for External Switch | Iin-leak | 1 | A | Venable = 3.3 V | 4 | ||
| Maximum Fanout for Fault Signal | Fan | 3 | Units | Total number of chips connected to this pin for simultaneous shutdown | 4 | ||
| Bias Current (Operational) | IBias | 450 | A | 4 | |||
| Bias Current (Shutdown) | IBias | 150 | A | 4 | |||
| Minimum Operating Voltage | Vmin | 7.7 | V | Notes 3 and 5 | 4 | ||
| Input Voltage operating, steady-state (VCC to GND) | VIN | -0.6 | 18 | V | VCC to GND, Note 1 | 3 | |
| Input Voltage transient (100 ms) | VIN | -0.6 | 25 | V | Transient (100 ms) | 3 | |
| Input Voltage input range | 8 | 18 | V | Features list | 1 | ||
| Operating Ambient Temperature Range | TA | -40 | 125 | °C | 3 | ||
| Operating Junction Temperature Range | TJ | -40 | 150 | °C | 3 | ||
| Non-operating Temperature Range | TSTG | -55 | 155 | °C | 3 | ||
| Lead Temperature, Soldering | TL | 260 | °C | 10 Sec | 3 | ||
| Total Power Dissipation | Pmax | 1.39 | W | TA = 25°C, 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu | 3 | ||
| Derating above 25°C | Pmax | 11.1 | mW/°C | Derate above 25°C | 3 | ||
| Thermal Resistance, Junction-to-Air | JA | 90 | °C/W | 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu | 3 | ||
| Thermal Characterization Parameter, Junction-to-Lead | J-L | 27.5 | °C/W | 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu | 3 | ||
| Thermal Characterization Parameter, Junction-to-Board | J-B | 27.5 | °C/W | 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu | 3 | ||
| Thermal Characterization Parameter, Junction-to-Case Top | J-T | 7.6 | °C/W | 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu | 3 |
CAD (KiCad official)
- Symbol:
NIS5420MT4TXG - Footprint:
Package_DFN_QFN:WDFN-10-1EP_3x3mm_P0.5mm_EP1.8x2.5mm - 3D model: WDFN-10(3x3) (KiCad packages3D, STEP)
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (13 pp, sha256
c34c52ca832c3473, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).