main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers nis5420mt4txg: viewers rendered from the public page · Ray
nis5420mt4txg-hero.glb Publish 0.1.0 · Ray
nis5420mt4txg-hero.overlay.json Publish 0.1.0 · Ray
nis5420mt4txg.glb Publish 0.1.0 · Ray
nis5420mt4txg.kicad_mod Publish 0.1.0 · Ray
nis5420mt4txg.kicad_sym Publish 0.1.0 · Ray
nis5420mt4txg.lbr Publish 0.1.0 · Ray
nis5420mt4txg.step Publish 0.1.0 · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 11 pins · Ray

NIS5420MT4TXG

onsemi · Surge Suppressors · WDFN-10(3x3)

NIS5420MT4TXG from onsemi, in a WDFN-10(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Negative input voltage to the device, used as the internal reference for the IC.
2 dv/dt passive Controls the output voltage slew rate at turn-on with an internal capacitor giving about a 2 ms ramp; an external capacitor can lengthen the ramp, and the pin is left open if no extra delay is needed.
3 En/Flt bidirectional Tri-state bidirectional enable/fault pin that is pulled to ground by an open-drain or open-collector device to shut down the eFuse, reads about 1.4 V in thermal shutdown and about 3 V in normal operation, and must not be actively driven or loaded with a capacitor.
4 ILIM passive A resistor between this pin and the source pin sets the overload and short-circuit current limit levels.
5 NC unconnected No connection for the NIS5420MT4 (this pin is ISENSE only on the MT1, MT2, MT6, MT7 and MT8 variants).
6 Src power_out Source of the internal power FET and output terminal of the fuse.
7 Src power_out Source of the internal power FET and output terminal of the fuse.
8 Src power_out Source of the internal power FET and output terminal of the fuse.
9 Src power_out Source of the internal power FET and output terminal of the fuse.
10 Src power_out Source of the internal power FET and output terminal of the fuse.
11 VCC power_in Positive input voltage to the device on the belly pad, rated -0.6 to 18 V steady-state and -0.6 to 25 V for 100 ms transients.

Key specifications

Parameter Value
Manufacturer onsemi
Package WDFN-10(3x3)
Category TVS/Fuse/Board Level Protection
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Off State Output Voltage Voff 50 mV VCC = 18 Vdc, VGS = 0 Vdc 4
Continuous Current (TA = 25°C, 100 mm2 copper) ID 4.6 A TA = 25°C, 100 mm2 copper (Note 3) 4
Continuous Current (TA = 80°C, minimum copper) ID 3.5 A TA = 80°C, minimum copper 4
Shutdown Temperature TSD 150 175 200 °C Note 3 4
Thermal Shutdown Response Time TSDRes 10 15 20 s 4
Output Clamping Voltage (NIS5420MT1, NIS5420MT4, NIS5420MT5, NIS5420MT6) VClamp2 13.6 16 V NIS5420MT1, NIS5420MT4, NIS5420MT5, NIS5420MT6 4
Output Clamping Response Time TClamp_Res 10 s 4
Undervoltage Lockout (NIS5420MT1, NIS5420MT3, NIS5420MT4, NIS5420MT5, NIS5420MT6) VUVLO1 7.8 8.5 9.2 V NIS5420MT1, MT3, MT4, MT5, MT6 4
Kelvin Short Circuit Current Limit ILim-SS 1.76 2.1 2.64 A RLimit = 20, Note 4 4
Logic Level Low (Output Disabled) Vin-low 0.35 0.58 0.81 V 4
Logic Level Mid (Thermal Fault, Output Disabled) Vin-mid 0.82 1.4 1.95 V Thermal Fault, Output Disabled 4
Logic Level High (Output Enabled) Vin-high 1.96 2.6 3 V Output Enabled 4
High State Maximum Voltage Vin-max 2.51 4.6 5 V 4
Logic Low Sink Current Iin-low -15 -25 A Venable = 0 V 4
Logic High Leakage Current for External Switch Iin-leak 1 A Venable = 3.3 V 4
Maximum Fanout for Fault Signal Fan 3 Units Total number of chips connected to this pin for simultaneous shutdown 4
Bias Current (Operational) IBias 450 A 4
Bias Current (Shutdown) IBias 150 A 4
Minimum Operating Voltage Vmin 7.7 V Notes 3 and 5 4
Input Voltage operating, steady-state (VCC to GND) VIN -0.6 18 V VCC to GND, Note 1 3
Input Voltage transient (100 ms) VIN -0.6 25 V Transient (100 ms) 3
Input Voltage input range 8 18 V Features list 1
Operating Ambient Temperature Range TA -40 125 °C 3
Operating Junction Temperature Range TJ -40 150 °C 3
Non-operating Temperature Range TSTG -55 155 °C 3
Lead Temperature, Soldering TL 260 °C 10 Sec 3
Total Power Dissipation Pmax 1.39 W TA = 25°C, 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu 3
Derating above 25°C Pmax 11.1 mW/°C Derate above 25°C 3
Thermal Resistance, Junction-to-Air JA 90 °C/W 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu 3
Thermal Characterization Parameter, Junction-to-Lead J-L 27.5 °C/W 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu 3
Thermal Characterization Parameter, Junction-to-Board J-B 27.5 °C/W 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu 3
Thermal Characterization Parameter, Junction-to-Case Top J-T 7.6 °C/W 4 layer High-K JEDEC JESD51-7 PCB, 100 mm2, 2 oz. Cu 3

CAD (KiCad official)

  • Symbol: NIS5420MT4TXG
  • Footprint: Package_DFN_QFN:WDFN-10-1EP_3x3mm_P0.5mm_EP1.8x2.5mm
  • 3D model: WDFN-10(3x3) (KiCad packages3D, STEP)

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (13 pp, sha256 c34c52ca832c3473, retrieved 2026-11-10, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF