Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TPIC2810D

Texas Instruments · LED Drivers · SOIC-16

TPIC2810D from Texas Instruments, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VCC power_in Logic supply voltage input, recommended range 3.0 V to 5.5 V and absolute maximum 7 V with respect to GND.
2 SDA bidirectional Open-drain bidirectional I2C serial data terminal that requires an external pullup resistor.
3 DRAIN0 output Low-side power DMOS FET drain output for resistive loads, rated 40 V drain-to-source and 100 mA continuous sink current.
4 DRAIN1 output Low-side power DMOS FET drain output for resistive loads, rated 40 V drain-to-source and 100 mA continuous sink current.
5 DRAIN2 output Low-side power DMOS FET drain output for resistive loads, rated 40 V drain-to-source and 100 mA continuous sink current.
6 DRAIN3 output Low-side power DMOS FET drain output for resistive loads, rated 40 V drain-to-source and 100 mA continuous sink current.
7 A2 input Address input 2 that sets the device's I2C slave address bit A2.
8 G input Active-low output enable; driving G high turns all drain outputs off, and driving it low makes the output storage register transparent to the outputs.
9 A0 input Address input 0 that sets the device's I2C slave address bit A0.
10 A1 input Address input 1 that sets the device's I2C slave address bit A1.
11 DRAIN4 output Low-side power DMOS FET drain output for resistive loads, rated 40 V drain-to-source and 100 mA continuous sink current.
12 DRAIN5 output Low-side power DMOS FET drain output for resistive loads, rated 40 V drain-to-source and 100 mA continuous sink current.
13 DRAIN6 output Low-side power DMOS FET drain output for resistive loads, rated 40 V drain-to-source and 100 mA continuous sink current.
14 DRAIN7 output Low-side power DMOS FET drain output for resistive loads, rated 40 V drain-to-source and 100 mA continuous sink current.
15 SCL input I2C serial clock input, specified for 100 kHz, 400 kHz and 2 MHz operation.
16 GND power_in Ground reference; all device voltages are specified with respect to GND.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SOIC-16
Category LED Drivers
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Logic supply voltage VCC 3 5.5 V 5
Drain-to-source breakdown voltage V(BR)DSX 40 V ID = 1 mA 5
Source-to-drain diode forward voltage VSD 0.85 1.2 V IF = 100 mA 5
High-level input current IIH 1 µA VCC = 5.5 V, VI = VCC 5
Low-level input current IIL -1 µA VCC = 5.5 V, VI = 0 5
Low level output current; SDA IOL 13 mA VOL = 0.4 V 5
Leakage current; SDA IL -1 1 µA VI = VCC 5
Logic supply current, all outputs off ICC 0.62 1 mA VCC = 5.5 V, all outputs off 5
Logic supply current, all outputs on ICC 0.7 1 mA VCC = 5.5 V, all outputs on 5
Logic supply current at frequency ICC(FRQ) 0.74 1 mA fSCL = 100 kHz, all outputs off, CL = 30 pF, See Figure 3 5
Off-state drain current IDSX 0.3 0.6 µA VDS = 30 V, VCC = 5.5 V 5
Thermal shutdown hysteresis THYS 10 20 30 °C 5
Static drain-source on-state resistance rDS(on) 8 10.8 Ω ID = 100 mA, VCC = 3 V 5
Static drain-source on-state resistance rDS(on) 5.1 6.9 Ω ID = 100 mA, VCC = 4.5 V 5
Static drain-source on-state resistance rDS(on) 13 18.2 Ω ID = 100 mA, VCC = 3.0 V, TC = 125°C 5
Static drain-source on-state resistance rDS(on) 8 11.2 Ω ID = 100 mA, VCC = 4.5 V, TC = 125°C 5
Logic supply voltage VCC 3 5.5 V 4
Pulse drain output current 210 mA TC = 25°C, VCC = 5 V, all outputs on (see Notes 3 and 4 and Figure 8) 4
Operating case temperature TC -40 125 °C 4
Logic supply voltage VCC 7 V see Note 1 (voltages with respect to GND) 4
Logic input voltage range VI -0.3 7 V 4
Power DMOS drain-to-source voltage VDS 40 V see Note 2 4
Continuous source-to-drain diode anode current 210 mA 4
Pulsed source-to-drain diode anode current 420 mA see Note 3 (pulse duration ≤ 100 µs, duty cycle ≤ 2%) 4
Pulsed drain current, each output, all outputs on ID 210 mA TC = 25°C (see Note 3) 4
Peak drain current, single output IDM 210 mA TC = 25°C (see Note 3) 4
Operating virtual junction temperature range TJ -40 150 °C 4
Operating case temperature range TC -40 125 °C 4
Storage temperature range Tstg -65 150 °C 4
Junction-to-ambient thermal resistance RθJA 115 °C/W All 8 outputs with equal power 7
Serial clock frequency f(SCL) 100 kHz 6
Serial clock frequency f(SCL) 400 kHz 6
Bus free time between stop and start condition t(BUF) 4.7 µs SCL = 100 kHz 6
Bus free time between stop and start condition t(BUF) 1.3 µs SCL = 400 kHz 6
Tolerable spike width on bus t(SP) 50 ns 6
SCL low to data out valid (acknowledge) tpd(ACK) 120 ns 6
SCL low time tLOW 4.7 µs SCL = 100 kHz 6
SCL low time tLOW 1.3 µs SCL = 400 kHz 6
SCL high time tHIGH 4 µs SCL = 100 kHz 6
SCL high time tHIGH 600 ns SCL = 400 kHz 6
SDA to SCL setup time tsu(DAT) 250 ns SCL = 100 kHz 6
SDA to SCL setup time tsu(DAT) 100 ns SCL = 400 kHz 6
Start condition setup time tsu(STA) 4.7 µs SCL = 100 kHz 6
Start condition setup time tsu(STA) 600 ns SCL = 400 kHz 6
Stop condition setup time tsu(STO) 4 µs SCL = 100 kHz 6
Stop condition setup time tsu(STO) 600 ns SCL = 400 kHz 6
SDA to SCL hold time th(DAT) 50 ns 6
Start condition hold time th(STA) 4 µs SCL = 100 kHz 6
Start condition hold time th(STA) 600 ns SCL = 400 kHz 6
Rise time of SCL signal tr(SCL) 1000 ns SCL = 100 kHz 6
Rise time of SCL signal tr(SCL) 300 ns SCL = 400 kHz 6
Fall time of SCL signal tf(SCL) 300 ns SCL = 100 kHz 6
Rise time of SDA signal tr(SDA) 1000 ns SCL = 100 kHz 6
Rise time of SDA signal tr(SDA) 300 ns SCL = 400 kHz 6
Fall time of SDA signal tf(SDA) 300 ns SCL = 100 kHz 6
Rise time, drain output tr(OUT) 1.05 µs ID = 75 mA, See Figures 1, 2, and 6 6
Fall time, drain output tf(OUT) 0.89 µs 6

CAD (KiCad official)

  • Symbol: TPIC2810D
  • Footprint: Package_SO:SOIC-16_3.9x9.9mm_P1.27mm
  • 3D model: SOIC-16 (KiCad packages3D, STEP)
  • 3D model files: tpic2810d-etched.step / tpic2810d-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tpic2810d.step / tpic2810d.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (23 pp, sha256 e9e24b98c49770a4, retrieved 2026-11-10, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF