3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMAX3245EEAI+T
Analog Devices Inc./Maxim Integrated · RS232 ICs · SSOP-28
MAX3245EEAI+T from Analog Devices Inc./Maxim Integrated, in a SSOP-28. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | C2+ | passive | Positive terminal of the inverting charge-pump capacitor. |
| 2 | C2- | passive | Negative terminal of the inverting charge-pump capacitor. |
| 3 | V- | power_out | -5.5V generated by the charge pump. |
| 4 | R1IN | input | RS-232 receiver 1 input (±25V input range). |
| 5 | R2IN | input | RS-232 receiver 2 input (±25V input range). |
| 6 | R3IN | input | RS-232 receiver 3 input (±25V input range). |
| 7 | R4IN | input | RS-232 receiver 4 input (±25V input range). |
| 8 | R5IN | input | RS-232 receiver 5 input (±25V input range). |
| 9 | T1OUT | output | RS-232 transmitter 1 output. |
| 10 | T2OUT | output | RS-232 transmitter 2 output. |
| 11 | T3OUT | output | RS-232 transmitter 3 output. |
| 12 | T3IN | input | TTL/CMOS transmitter 3 input; connect unused inputs to GND or VCC. |
| 13 | T2IN | input | TTL/CMOS transmitter 2 input; connect unused inputs to GND or VCC. |
| 14 | T1IN | input | TTL/CMOS transmitter 1 input; connect unused inputs to GND or VCC. |
| 15 | R5OUT | tri_state | TTL/CMOS receiver 5 output, high impedance when FORCEOFF is low. |
| 16 | R4OUT | tri_state | TTL/CMOS receiver 4 output, high impedance when FORCEOFF is low. |
| 17 | R3OUT | tri_state | TTL/CMOS receiver 3 output, high impedance when FORCEOFF is low. |
| 18 | R2OUT | tri_state | TTL/CMOS receiver 2 output, high impedance when FORCEOFF is low. |
| 19 | R1OUT | tri_state | TTL/CMOS receiver 1 output, high impedance when FORCEOFF is low. |
| 20 | R2OUTB | output | TTL/CMOS noninverting complementary receiver 2 output, always active. |
| 21 | INVALID | output | Valid signal detector output, active low; logic high indicates a valid RS-232 level is present on a receiver input. |
| 22 | FORCEOFF | input | Force-off input, active low; drive low to shut down transmitters, receivers (except R2OUTB) and charge pump, overriding AutoShutdown Plus and FORCEON. |
| 23 | FORCEON | input | Force-on input, active high; drive high to override AutoShutdown Plus, keeping transmitters and receivers on (FORCEOFF must be high). |
| 24 | C1- | passive | Negative terminal of the voltage-doubler charge-pump capacitor. |
| 25 | GND | power_in | Ground. |
| 26 | VCC | power_in | +3.0V to +5.5V single supply voltage. |
| 27 | V+ | power_out | +5.5V generated by the charge pump. |
| 28 | C1+ | passive | Positive terminal of the voltage-doubler charge-pump capacitor. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices Inc./Maxim Integrated |
| Package | SSOP-28 |
| Category | Interface |
| Pins | 28 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 3 | 5.5 | V | Single supply voltage | 7 | |
| Operating temperature (E grade) | TA | -40 | 85 | °C | MAX32__E__ | 2 | |
| Supply current, shutdown | ICC | 1 | 10 | µA | FORCEOFF = GND | 2 | |
| Supply current, AutoShutdown Plus | ICC | 1 | 10 | µA | FORCEON = GND, FORCEOFF = VCC, all R_IN idle, all T_IN idle | 2 | |
| Supply current, AutoShutdown Plus disabled | ICC | 0.3 | 1 | mA | FORCEON = FORCEOFF = VCC, no load | 2 | |
| Input logic threshold low | VIL | 0.8 | V | T_IN, FORCEON, FORCEOFF | 2 | ||
| Input logic threshold high | VIH | 2.4 | V | T_IN, FORCEON, FORCEOFF | 2 | ||
| Transmitter input hysteresis | 0.5 | V | 2 | ||||
| Input leakage current | 0.01 | 1 | µA | T_IN, FORCEON, FORCEOFF | 2 | ||
| Receiver output leakage current | 0.05 | 10 | µA | R_OUT (MAX3244/MAX3245), receivers disabled | 2 | ||
| Receiver output voltage low | VOL | 0.4 | V | IOUT = 1.6mA | 2 | ||
| Receiver input voltage range | -25 | 25 | V | 2 | |||
| Receiver input threshold low, VCC = 3.3V | 0.6 | 1.2 | V | VCC = 3.3V, TA = +25°C | 2 | ||
| Receiver input threshold low, VCC = 5.0V | 0.8 | 1.5 | V | VCC = 5.0V, TA = +25°C | 2 | ||
| Receiver input threshold high, VCC = 3.3V | 1.5 | 2.4 | V | VCC = 3.3V, TA = +25°C | 2 | ||
| Receiver input threshold high, VCC = 5.0V | 1.8 | 2.4 | V | VCC = 5.0V, TA = +25°C | 2 | ||
| Receiver input hysteresis | 0.5 | V | 2 | ||||
| Receiver input resistance | 3 | 5 | 7 | kΩ | TA = +25°C | 2 | |
| Transmitter output voltage swing | 5 | 5.4 | V | All transmitter outputs loaded with 3kΩ to ground | 3 | ||
| Transmitter output short-circuit current | 60 | mA | 3 | ||||
| Transmitter output leakage current | 25 | µA | VCC = 0 or 3V to 5.5V, VOUT = ±12V, Transmitters disabled | 3 | |||
| Mouse driveability transmitter output voltage | 5 | V | T1IN = T2IN = GND, T3IN = VCC, T3OUT loaded with 3kΩ to GND, T1OUT and T2OUT loaded with 2.5mA each | 3 | |||
| Receiver or transmitter edge to transmitters shutdown | tAUTOSHDN | 15 | 30 | 60 | s | Figure 4b | 3 |
| Receiver or transmitter edge to transmitters enabled | tWU | 100 | µs | VCC = 5V, Figure 4b | 3 | ||
| Receiver threshold to INVALID low | tINVL | 30 | µs | VCC = 5V, Figure 5b (Note 2) | 3 | ||
| Receiver threshold to INVALID high | tINVH | 1 | µs | VCC = 5V, Figure 5b (Note 2) | 3 | ||
| INVALID, READY output voltage low | 0.4 | V | IOUT = -1.6mA | 3 | |||
| Receiver input threshold to INVALID output low | -0.3 | 0.3 | V | Figure 4a | 3 | ||
| Receiver input threshold to INVALID output high, positive threshold | 2.7 | V | Figure 4a, positive threshold | 3 | |||
| Receiver input threshold to INVALID output high, negative threshold | -2.7 | V | Figure 4a, negative threshold | 3 | |||
| Maximum data rate | 250 | kbps | RL = 3kΩ, CL = 1000pF, one transmitter switching | 4 | |||
| Maximum data rate | 1000 | kbps | 4 | ||||
| Receiver propagation delay tPHL | tPHL | 0.15 | µs | R_IN to R_OUT, CL = 150pF | 4 | ||
| Receiver propagation delay tPLH | tPLH | 0.15 | µs | R_IN to R_OUT, CL = 150pF | 4 | ||
| Transition-region slew rate | 24 | 150 | V/µs | VCC = 3.3V, TA = +25°C, RL = 3kΩ to 7kΩ, CL = 150pF to 1000pF, measured from +3V to -3V or -3V to +3V | 4 | ||
| Receiver output enable time | 200 | ns | Normal operation (MAX3245 only) | 4 | |||
| Receiver output disable time | 200 | ns | Normal operation (MAX3245 only) | 4 | |||
| Transmitter skew /tPHL - tPLH/ | 25 | ns | (Note 3) | 4 | |||
| Receiver skew /tPHL - tPLH/ | 50 | ns | 4 | ||||
| VCC to GND | VCC | -0.3 | 6 | V | 2 | ||
| V+ to GND | V+ | -0.3 | 7 | V | Note 1 | 2 | |
| V- to GND | V- | -7 | 0.3 | V | Note 1 | 2 | |
| V+ + /V-/ | 13 | V | Note 1 | 2 | |||
| T_IN, FORCEON, FORCEOFF to GND | -0.3 | 6 | V | 2 | |||
| R_IN to GND | -25 | 25 | V | 2 | |||
| T_OUT to GND | -13.2 | 13.2 | V | 2 | |||
| R_OUT, INVALID, READY to GND | -0.3 | V | to (VCC + 0.3V) | 2 | |||
| Storage temperature | -65 | 160 | °C | 2 | |||
| Lead temperature (soldering, 10s) | 300 | °C | 2 | ||||
| Soldering temperature (reflow) | 260 | °C | 2 |
CAD (KiCad official)
- Symbol:
MAX3245EEAI+T - Footprint:
Package_SO:SSOP-28_5.3x10.2mm_P0.65mm - 3D model: SSOP-28 (KiCad packages3D, STEP)
- 3D model files:
max3245eeai-t-etched.step/max3245eeai-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);max3245eeai-t.step/max3245eeai-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices Inc./Maxim Integrated datasheet (19 pp, sha256
cb52c14514f7e6c3, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).