3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTPS7A7850PWPR
Texas Instruments · Linear Voltage Regulators (LDO) · HTSSOP-14-EP
TPS7A7850PWPR from Texas Instruments, in a HTSSOP-14-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SC1- | passive | Negative terminal of the switched-capacitor voltage-reduction stage; connect a minimum 1-µF, X5R (or better), 16-V-rated capacitor between this pin and SC1+. |
| 2 | SC1+ | passive | Positive terminal of the switched-capacitor voltage-reduction stage; connect a minimum 1-µF, X5R (or better), 16-V-rated capacitor between this pin and SC1-. |
| 3 | SCIN | power_in | Rectified DC-voltage input pin; place the bulk capacitor as close to the device as possible. |
| 4 | PFD | input | Power-failure detect analog input that compares the reference voltage to a resistor-divided VSCIN voltage to detect a VAC power failure. |
| 5 | AC+ | power_in | AC-supply line or neutral input after the cap-drop capacitor and surge resistor; either AC+ or AC- must have the cap-drop capacitor and surge resistor in series with the line. |
| 6 | GND | power_in | Ground pin; all device ground pins must be referenced to the same ground and connected to the thermal pad. |
| 7 | AC- | power_in | AC-supply line or neutral input after the cap-drop capacitor and surge resistor; either AC- or AC+ must have the cap-drop capacitor and surge resistor in series with the line. |
| 8 | LDO_OUT | power_out | Regulated DC output pin; connect a minimum 0.68-µF, X5R (or better) capacitor between this pin and the device GND pins, with a maximum CLDO_OUT of 100 µF. |
| 9 | LDO_IN | power_out | Charge-pump output pin, internally driven and must not be driven externally; connect a minimum 0.68-µF, X5R (or better) capacitor between this pin and the device GND pins. |
| 10 | PF | output | Open-drain power-fail indicator that goes low when VPFD is less than the VIT(PFD,FALLING) threshold; pull up through an external resistor. |
| 11 | PG | output | Open-drain power-good indicator that signals when VLDO_OUT surpasses the VIT(PG,RISING) threshold; pull up through an external resistor to VLDO_OUT or a DC rail sharing the device GND. |
| 12 | GND | power_in | Ground pin; all device ground pins must be referenced to the same ground and connected to the thermal pad. |
| 13 | SC2+ | passive | Positive terminal of the switched-capacitor voltage-reduction stage; connect a minimum 1-µF, X5R (or better), 10-V-rated capacitor between this pin and SC2-. |
| 14 | SC2- | passive | Negative terminal of the switched-capacitor voltage-reduction stage; connect a minimum 1-µF, X5R (or better), 10-V-rated capacitor between this pin and SC2+. |
| 15 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-14-EP |
| Category | Power Supply Chip |
| Pins | 15 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| AC+, AC- voltage (VAC supply mode only) | -1.5 | 30 | V | VAC supply mode only | 4 | ||
| SCIN voltage (VAC supply mode only, internally driven) | -1.5 | 30 | V | VAC supply mode only, internally driven | 4 | ||
| SCIN voltage (DC supply mode only) | -0.3 | 24 | V | DC supply mode only, voltage directly applied on SCIN pin | 4 | ||
| LDO_OUT voltage | -0.3 | 5.5 | V | 4 | |||
| PF, PG voltage | -0.3 | 6 | V | 4 | |||
| PFD voltage | -0.3 | 3 | V | 4 | |||
| LDO_OUT pin reverse current | 6 | mA | 4 | ||||
| Maximum output current IPF, IPG | IPF, IPG | 5 | mA | 4 | |||
| Storage temperature | TSTG | -65 | 150 | °C | 4 | ||
| VAC supply voltage | VAC | 18 | VRMS | Connected via CS and RS on either AC+ or AC- | 5 | ||
| Line frequency | fAC | 50 | 20000 | Hz | 5 | ||
| Peak transient current into or out of AC+ or AC- pins | ISURGE | 2.5 | A | During hot plug for <=100 µs | 5 | ||
| AC current during shunt event on AC+ or AC- pins | ISHUNT | 200 | mARMS | 5 | |||
| Bulk capacitor for VAC supply mode | CSCIN | 22 | µF | VAC supply mode | 5 | ||
| Switched-capacitor stage 1 capacitor | CSC1 | 1 | 4.7 | µF | 16 V or higher rating recommended | 5 | |
| Switched-capacitor stage 2 capacitor | CSC2 | 1 | 4.7 | µF | 10 V or higher rating recommended | 5 | |
| LDO_IN capacitor | CLDO_IN | 0.68 | 10 | 1000 | µF | 5 | |
| LDO_OUT capacitor | CLDO_OUT | 0.68 | 1 | 100 | µF | 5 | |
| PFD top resistor divider | R1 | 0 | 200 | kΩ | 5 | ||
| Power-good and power-fail pullup resistors | R3, R4 | 10 | 100 | kΩ | 5 | ||
| Output current | IOUT | 0 | 120 | mA | 5 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 5 | ||
| Junction-to-ambient thermal resistance | RθJA | 48 | °C/W | 5 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 44 | °C/W | 5 | |||
| Junction-to-board thermal resistance | RθJB | 24.2 | °C/W | 5 | |||
| Junction-to-top characterization parameter | ΨJT | 1.6 | °C/W | 5 | |||
| Junction-to-board characterization parameter | ΨJB | 24.1 | °C/W | 5 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 7.2 | °C/W | 5 | |||
| UVLO_LDO_IN threshold rising | VUVLO_LDO_IN | 3.9 | V | VSCIN rising | 6 | ||
| UVLO_LDO_IN threshold falling | VUVLO_LDO_IN | 3.5 | V | VSCIN falling | 6 | ||
| Load regulation | ΔVLDO_OUT(ΔIOUT) | 0.21 | mV/mA | 0 mA <= IOUT <= 120 mA | 6 | ||
| Output voltage accuracy | VLDO_OUT | -2 | 1 | 2 | % | VSCIN = 4(VLDO_OUT(nom)+0.6 V)+3 V, 0 mA <= IOUT <= 120 mA | 6 |
| Output current limit | ICL | 145 | 215 | 300 | mA | VLDO_OUT = 0.9 x VLDO_OUT(nom) | 6 |
| Output voltage ripple | VRipple | 3 | mV | VAC = 120 V, 60 Hz, FB, CS = 1.0 µF, CSCIN = 180 µF, VLDO_OUT(nom) = 5 V, IOUT = 10 mA, scope BW = 10 MHz | 6 | ||
| PFD pin rising threshold | VIT(PFD,RISING) | 1.24 | 1.42 | V | VPFD rising, R4 = 100 kΩ | 6 | |
| PFD pin falling threshold | VIT(PFD,FALLING) | 1.17 | 1.25 | V | VPFD falling, R4 = 100 kΩ | 6 | |
| PFD pin hysteresis | VHYS(PFD) | 110 | mV | 6 | |||
| PG pin rising threshold | VIT(PG,RISING) | 90.16 | 92 | 93.84 | %VLDO_OUT | R3 = 100 kΩ, VSCIN rising | 6 |
| PG pin falling threshold | VIT(PG,FALLING) | 88.5 | 90 | 91.5 | %VLDO_OUT | R3 = 100 kΩ | 6 |
| PG pin hysteresis | VHYS(PG) | 2 | %VLDO_OUT | 6 | |||
| PF and PG pins low-level output voltage | VOL(PF),(PG) | 0.2 | V | IPF,PG = 500 µA | 6 | ||
| PF and PG pins open-drain leakage current | ILKG(PF),(PG) | 50 | nA | VPF,PG = 5 V | 6 | ||
| Thermal shutdown temperature | TSD(Shutdown) | 162 | °C | Shutdown, temperature increasing | 6 | ||
| Thermal shutdown reset temperature | TSD(Reset) | 135 | °C | Reset, temperature decreasing | 6 | ||
| PF pin high-to-low time | tPF(HL) | 1 | µs | PF pin going from high to low | 6 | ||
| PG pin low-to-high time | tPG(LH) | 1 | µs | PG pin going from low to high | 6 | ||
| Switched capacitor stage operating frequency | fSC | 200 | kHz | 6 |
CAD (KiCad official)
- Symbol:
TPS7A7850PWPR - Footprint:
Package_SO:TSSOP-14-1EP_4.4x5mm_P0.65mm - 3D model: HTSSOP-14-EP (KiCad packages3D, STEP)
- 3D model files:
tps7a7850pwpr-etched.step/tps7a7850pwpr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps7a7850pwpr.step/tps7a7850pwpr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (40 pp, sha256
c7082dade63e2c4c, retrieved 2026-10-28, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).