Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

ZSSC3240CI3W

RENESAS · ADC/DAC - Specialized · QFN-24(4x4)

ZSSC3240CI3W from RENESAS, in a QFN-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VDDB bidirectional Positive sensor (bridge) supply or sensor-signal input.
2 INP input Positive sensor (bridge) signal input.
3 VSSB power_in Sensor (bridge) ground or sensor-signal input; the datasheet lists the pin as Analog Input and states that the ratiometric VSSB level must not exceed 0.7 V (VSSBratio_max).
4 INN input Negative sensor (bridge) signal input; absolute sensor signal input level is specified as 0.5 V to 1.2 V.
5 IDT-test unconnected Renesas-internal use only; connect to VSS or leave unconnected, floating.
6 IDT-test unconnected Renesas-internal use only; connect to VSS or leave unconnected, floating.
7 RESQ input Digital IC reset, low active, with internal pull-up.
8 IDT-test unconnected Renesas-internal use only; connect to VSS or leave unconnected, floating.
9 MOSI/SDA bidirectional Digital data input for SPI or bidirectional data I/O for I2C; pull-up to VDD required.
10 n.c. unconnected No connection; leave floating.
11 SCLK/SCL input Clock input for SPI or I2C interface, referenced to the applied VDD level.
12 MISO output Data output from ZSSC3240 to master for SPI interface, referenced to the applied VDD level.
13 SS input Slave select (interface enable) for SPI, referenced to the applied VDD level.
14 EOC output End-of-conversion and output interrupt signal.
15 OWI2in input Optional OWI interface input line for current-loop applications.
16 AOUT/OWI1 bidirectional Analog smart-sensor output signal (absolute or ratiometric voltage output) and/or OWI interface input/output line.
17 FB output Current-loop application feedback output at a level below VSS; no connection if not used.
18 VSS power_in Power supply ground.
19 VDD power_in Power supply; 2.7 V to 5.5 V recommended operating range.
20 n.c. unconnected No connection; leave floating.
21 TEXT output Current drive output for external temperature sensor and/or bridge in Current Mode; a 1500 Ω serial resistor is built in internally for pad protection.
22 n.c. unconnected No connection; leave floating.
23 LDOctrl output Control output (reference signal) for an optional external regulator or supply control loop.
24 n.c. unconnected No connection; leave floating.
25 Exposed PAD unconnected QFN bottom plate (die bottom/substrate); leave floating with no electrical connection and use only for heat dissipation.

Key specifications

Parameter Value
Manufacturer RENESAS
Package QFN-24(4x4)
Category Data Converters
Pins 25

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Maximum allowed for voltage supply VDD_max -0.3 6.5 V Referenced to VSS 8
Voltage at digital interface pins VIF_max -0.3 5.5 V I2C pins: SDA, SCL 8
Voltage at FB pin VFB_max -2 2 V 4mA to 20mA current loop interface 8
Latch-up -100 100 mA 8
ESD, Human Body Model 4000 V 8
ESD, Charged Device Model 750 V 8
Junction temperature TJ 135 °C 8
Storage temperature TS -45 150 °C 8
Power supply voltage VDD 2.7 5.5 V 8
Ambient temperature TA -40 125 °C depending on the part code 8
External (parasitic) capacitance between VDD and VSS CVDD 0 10 nF without external supply transistor regulation 8
External (parasitic) capacitance between VDD and VSS CVDD 80 100 120 nF with (optional) external supply transistor regulation 8
Recommended external capacitance between VDDB and VSS for EMI CVDDB,EMC 0 6.8 8 nF 8
Recommended external capacitance between AOUT versus VSS and versus VDD for EMI CAOUT,EMC 0 22 33 nF for applications with OWI-interface or analog voltage-output 8
Sensor load current through external sensor element ISensor 0.02 0.5 4 mA ratiometric sensor supply configuration 8
External temperature diode and RTD input range, drop over external element VDioDrop -0.2 1 V referenced to TEXT pin 8
Absolute sensor signal input level, INN, INP pins VSens_in 0.5 1.2 V 8
Minimum level at VDDB VDDBratio_min 0.9 V ratiometric sensor supply configuration 8
Maximum level at VSSB VSSBratio_max 0.7 V ratiometric sensor supply configuration 8
Maximum current load at AOUT pin for voltage outputs Imax_AOUT_V 18 mA 8
Recommended VDD rise slew rate for power-on-reset (POR) SRVDD_POR 1.5 V/ms 8
Current consumption, active IC IIC 2.3 2.8 mA excluding connected sensor elements, with LDOctrl enabled 8
Idle current consumption, IC in Idle State IIDLE 1.5 6 µA typical at 30°C, maximum at 85°C; OWI and LDOctrl disabled 8
Idle current consumption, IC in Idle State IIDLE 22 µA maximum at 125°C; OWI and LDOctrl disabled 8
Average current draw IAVE 3.5 µA mean current per complete SSC measurement cycle per second at 16-bit digital-only output 9
Target level regulation range to generate VDD after external transistor VDD,LDOctrl 4.6 5.2 5.5 V using LDOctrl and external transistor; programmable VDD_ldoctrl_target 9
Sensor bias ISUP 5 80 500 µA current mode sensor supply; setup in temp_source and sensor_sup 9
Relative sensor bias current error ErrTBIAS -3.5 -1 1.5 % 9
Drop over sensor bias current source VTBIAS 200 230 mV referenced VDDAint from internal analog regulator 9
Internally regulated analog (bridge) sensor front-end supply VDDB (VDDAint) 1.68 1.75 1.8 V ratiometric sensor supply; setup in temp_source and sensor_sup 9
Power supply rejection ratio, only internal regulator PSRRLOW 45 50 dB fVDD = 0Hz to 10MHz 9
Power supply rejection ratio, only internal regulator PSRRHIGH 20 dB fVDD > 10MHz 9
Resolution rADC 12 16 24 Bit 9
Single-conversion rate, conversions per second fS,raw 0.21 3.39 13 kHz single external sensor A2D conversion without AZ; printed min = ADC 24-bit, typ = ADC 16-bit, max = ADC 12-bit 9
Effective number of bits, noise based ENOB 15.8 18.1 Bit gain < 78, shorted input, rADC = 24-bit, no oversampling 9
DAC Resolution rDAC 13 14 16 Bit 9
Analog voltage output settling time tDACsettle 0 65 150 µs time from 30% steady state until 99% of new DAC output value 9
Addressable output voltage at AOUT pin VDACout 0.025 1 V absolute output, Aout_setup = 010BIN 9
Addressable output voltage at AOUT pin VDACout 0.025 5 V absolute output, VDD > 5.01V, Aout_setup = 011BIN 9
Addressable output voltage at AOUT pin VDACout 0.1 100 %VDD ratiometric output, Aout_setup = 001BIN 9
Output filter bandwidth BWDAC 12 15 20 kHz without external components 9
Output slew rate SRout 20 100 mV/µs resistive load > 2kΩ, capacitive load < 20nF at Aout, temperature = 25°C 9
Maximum output current IOUTmax 10 12 18 mA must be overdriven from OWI-Master if concurrent DAC-output and OWI communication 9
Current loop driving current IDRloop 100 160 µA Aout_setup = 000BIN; depends on connected bipolar transistor 9
Gain Gamp 1.32 540 V/V 120 steps 9
Gain error Gerr -2.5 0 2.5 % referenced to nominal gain, T = 25°C 9
Supported input common mode VCMin 0.7 0.85 1 V VDDAint = 1.75V; valid for ratiometric and current mode sensor supply 9
Output (Update) rate fSSCout 0.07 1.45 2.91 kHz cyclic operation 9
Output (Update) rate, complete SSC cycle (S, T) including analog output update fSSCout 1.35 1.45 1.6 kHz ADC 14-bit; DAC 14-bit 9
Relative accuracy of the effectively applied Offset Shift IOFFSC 0.89 0.98 1.07 - referenced to selected setup per ioffsc[4:0], IC-to-IC variation 14
1st order temperature coefficient for negative-voltage shift effects TCneg,IOFFSC -0.25 -0.21 0 PPT/K ioffsc[4]=0 14
1st order temperature coefficient for positive-voltage shift effects TCpos,IOFFSC 0 0.21 0.25 PPT/K ioffsc[4]=1 14
External, extra LDO: allowed parasitic capacitance at LDOctrl pin Cctrl 150 500 pF external LDO operating conditions 58
Buffer/filter capacitance between VDD and VSS CVDD 80 100 120 nF external LDO operating conditions (LDOctrl applications) 58

CAD (KiCad official)

  • Symbol: ZSSC3240CI3W
  • Footprint: Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm
  • 3D model: QFN-24(4x4) (KiCad packages3D, STEP)
  • 3D model files: zssc3240ci3w-etched.step / zssc3240ci3w-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); zssc3240ci3w.step / zssc3240ci3w.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENESAS datasheet (64 pp, sha256 db57129dd2ce085e, retrieved 2026-10-30, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF