Generated by kicad-footprint-generator · KiCad file format 20260206
ZSSC3240CI3W
RENESAS · ADC/DAC - Specialized · QFN-24(4x4)
ZSSC3240CI3W from RENESAS, in a QFN-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDDB | bidirectional | Positive sensor (bridge) supply or sensor-signal input. |
| 2 | INP | input | Positive sensor (bridge) signal input. |
| 3 | VSSB | power_in | Sensor (bridge) ground or sensor-signal input; the datasheet lists the pin as Analog Input and states that the ratiometric VSSB level must not exceed 0.7 V (VSSBratio_max). |
| 4 | INN | input | Negative sensor (bridge) signal input; absolute sensor signal input level is specified as 0.5 V to 1.2 V. |
| 5 | IDT-test | unconnected | Renesas-internal use only; connect to VSS or leave unconnected, floating. |
| 6 | IDT-test | unconnected | Renesas-internal use only; connect to VSS or leave unconnected, floating. |
| 7 | RESQ | input | Digital IC reset, low active, with internal pull-up. |
| 8 | IDT-test | unconnected | Renesas-internal use only; connect to VSS or leave unconnected, floating. |
| 9 | MOSI/SDA | bidirectional | Digital data input for SPI or bidirectional data I/O for I2C; pull-up to VDD required. |
| 10 | n.c. | unconnected | No connection; leave floating. |
| 11 | SCLK/SCL | input | Clock input for SPI or I2C interface, referenced to the applied VDD level. |
| 12 | MISO | output | Data output from ZSSC3240 to master for SPI interface, referenced to the applied VDD level. |
| 13 | SS | input | Slave select (interface enable) for SPI, referenced to the applied VDD level. |
| 14 | EOC | output | End-of-conversion and output interrupt signal. |
| 15 | OWI2in | input | Optional OWI interface input line for current-loop applications. |
| 16 | AOUT/OWI1 | bidirectional | Analog smart-sensor output signal (absolute or ratiometric voltage output) and/or OWI interface input/output line. |
| 17 | FB | output | Current-loop application feedback output at a level below VSS; no connection if not used. |
| 18 | VSS | power_in | Power supply ground. |
| 19 | VDD | power_in | Power supply; 2.7 V to 5.5 V recommended operating range. |
| 20 | n.c. | unconnected | No connection; leave floating. |
| 21 | TEXT | output | Current drive output for external temperature sensor and/or bridge in Current Mode; a 1500 Ω serial resistor is built in internally for pad protection. |
| 22 | n.c. | unconnected | No connection; leave floating. |
| 23 | LDOctrl | output | Control output (reference signal) for an optional external regulator or supply control loop. |
| 24 | n.c. | unconnected | No connection; leave floating. |
| 25 | Exposed PAD | unconnected | QFN bottom plate (die bottom/substrate); leave floating with no electrical connection and use only for heat dissipation. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | QFN-24(4x4) |
| Category | Data Converters |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Maximum allowed for voltage supply | VDD_max | -0.3 | 6.5 | V | Referenced to VSS | 8 | |
| Voltage at digital interface pins | VIF_max | -0.3 | 5.5 | V | I2C pins: SDA, SCL | 8 | |
| Voltage at FB pin | VFB_max | -2 | 2 | V | 4mA to 20mA current loop interface | 8 | |
| Latch-up | -100 | 100 | mA | 8 | |||
| ESD, Human Body Model | 4000 | V | 8 | ||||
| ESD, Charged Device Model | 750 | V | 8 | ||||
| Junction temperature | TJ | 135 | °C | 8 | |||
| Storage temperature | TS | -45 | 150 | °C | 8 | ||
| Power supply voltage | VDD | 2.7 | 5.5 | V | 8 | ||
| Ambient temperature | TA | -40 | 125 | °C | depending on the part code | 8 | |
| External (parasitic) capacitance between VDD and VSS | CVDD | 0 | 10 | nF | without external supply transistor regulation | 8 | |
| External (parasitic) capacitance between VDD and VSS | CVDD | 80 | 100 | 120 | nF | with (optional) external supply transistor regulation | 8 |
| Recommended external capacitance between VDDB and VSS for EMI | CVDDB,EMC | 0 | 6.8 | 8 | nF | 8 | |
| Recommended external capacitance between AOUT versus VSS and versus VDD for EMI | CAOUT,EMC | 0 | 22 | 33 | nF | for applications with OWI-interface or analog voltage-output | 8 |
| Sensor load current through external sensor element | ISensor | 0.02 | 0.5 | 4 | mA | ratiometric sensor supply configuration | 8 |
| External temperature diode and RTD input range, drop over external element | VDioDrop | -0.2 | 1 | V | referenced to TEXT pin | 8 | |
| Absolute sensor signal input level, INN, INP pins | VSens_in | 0.5 | 1.2 | V | 8 | ||
| Minimum level at VDDB | VDDBratio_min | 0.9 | V | ratiometric sensor supply configuration | 8 | ||
| Maximum level at VSSB | VSSBratio_max | 0.7 | V | ratiometric sensor supply configuration | 8 | ||
| Maximum current load at AOUT pin for voltage outputs | Imax_AOUT_V | 18 | mA | 8 | |||
| Recommended VDD rise slew rate for power-on-reset (POR) | SRVDD_POR | 1.5 | V/ms | 8 | |||
| Current consumption, active IC | IIC | 2.3 | 2.8 | mA | excluding connected sensor elements, with LDOctrl enabled | 8 | |
| Idle current consumption, IC in Idle State | IIDLE | 1.5 | 6 | µA | typical at 30°C, maximum at 85°C; OWI and LDOctrl disabled | 8 | |
| Idle current consumption, IC in Idle State | IIDLE | 22 | µA | maximum at 125°C; OWI and LDOctrl disabled | 8 | ||
| Average current draw | IAVE | 3.5 | µA | mean current per complete SSC measurement cycle per second at 16-bit digital-only output | 9 | ||
| Target level regulation range to generate VDD after external transistor | VDD,LDOctrl | 4.6 | 5.2 | 5.5 | V | using LDOctrl and external transistor; programmable VDD_ldoctrl_target | 9 |
| Sensor bias | ISUP | 5 | 80 | 500 | µA | current mode sensor supply; setup in temp_source and sensor_sup | 9 |
| Relative sensor bias current error | ErrTBIAS | -3.5 | -1 | 1.5 | % | 9 | |
| Drop over sensor bias current source | VTBIAS | 200 | 230 | mV | referenced VDDAint from internal analog regulator | 9 | |
| Internally regulated analog (bridge) sensor front-end supply | VDDB (VDDAint) | 1.68 | 1.75 | 1.8 | V | ratiometric sensor supply; setup in temp_source and sensor_sup | 9 |
| Power supply rejection ratio, only internal regulator | PSRRLOW | 45 | 50 | dB | fVDD = 0Hz to 10MHz | 9 | |
| Power supply rejection ratio, only internal regulator | PSRRHIGH | 20 | dB | fVDD > 10MHz | 9 | ||
| Resolution | rADC | 12 | 16 | 24 | Bit | 9 | |
| Single-conversion rate, conversions per second | fS,raw | 0.21 | 3.39 | 13 | kHz | single external sensor A2D conversion without AZ; printed min = ADC 24-bit, typ = ADC 16-bit, max = ADC 12-bit | 9 |
| Effective number of bits, noise based | ENOB | 15.8 | 18.1 | Bit | gain < 78, shorted input, rADC = 24-bit, no oversampling | 9 | |
| DAC Resolution | rDAC | 13 | 14 | 16 | Bit | 9 | |
| Analog voltage output settling time | tDACsettle | 0 | 65 | 150 | µs | time from 30% steady state until 99% of new DAC output value | 9 |
| Addressable output voltage at AOUT pin | VDACout | 0.025 | 1 | V | absolute output, Aout_setup = 010BIN | 9 | |
| Addressable output voltage at AOUT pin | VDACout | 0.025 | 5 | V | absolute output, VDD > 5.01V, Aout_setup = 011BIN | 9 | |
| Addressable output voltage at AOUT pin | VDACout | 0.1 | 100 | %VDD | ratiometric output, Aout_setup = 001BIN | 9 | |
| Output filter bandwidth | BWDAC | 12 | 15 | 20 | kHz | without external components | 9 |
| Output slew rate | SRout | 20 | 100 | mV/µs | resistive load > 2kΩ, capacitive load < 20nF at Aout, temperature = 25°C | 9 | |
| Maximum output current | IOUTmax | 10 | 12 | 18 | mA | must be overdriven from OWI-Master if concurrent DAC-output and OWI communication | 9 |
| Current loop driving current | IDRloop | 100 | 160 | µA | Aout_setup = 000BIN; depends on connected bipolar transistor | 9 | |
| Gain | Gamp | 1.32 | 540 | V/V | 120 steps | 9 | |
| Gain error | Gerr | -2.5 | 0 | 2.5 | % | referenced to nominal gain, T = 25°C | 9 |
| Supported input common mode | VCMin | 0.7 | 0.85 | 1 | V | VDDAint = 1.75V; valid for ratiometric and current mode sensor supply | 9 |
| Output (Update) rate | fSSCout | 0.07 | 1.45 | 2.91 | kHz | cyclic operation | 9 |
| Output (Update) rate, complete SSC cycle (S, T) including analog output update | fSSCout | 1.35 | 1.45 | 1.6 | kHz | ADC 14-bit; DAC 14-bit | 9 |
| Relative accuracy of the effectively applied Offset Shift | IOFFSC | 0.89 | 0.98 | 1.07 | - | referenced to selected setup per ioffsc[4:0], IC-to-IC variation | 14 |
| 1st order temperature coefficient for negative-voltage shift effects | TCneg,IOFFSC | -0.25 | -0.21 | 0 | PPT/K | ioffsc[4]=0 | 14 |
| 1st order temperature coefficient for positive-voltage shift effects | TCpos,IOFFSC | 0 | 0.21 | 0.25 | PPT/K | ioffsc[4]=1 | 14 |
| External, extra LDO: allowed parasitic capacitance at LDOctrl pin | Cctrl | 150 | 500 | pF | external LDO operating conditions | 58 | |
| Buffer/filter capacitance between VDD and VSS | CVDD | 80 | 100 | 120 | nF | external LDO operating conditions (LDOctrl applications) | 58 |
CAD (KiCad official)
- Symbol:
ZSSC3240CI3W - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: QFN-24(4x4) (KiCad packages3D, STEP)
- 3D model files:
zssc3240ci3w-etched.step/zssc3240ci3w-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);zssc3240ci3w.step/zssc3240ci3w.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (64 pp, sha256
db57129dd2ce085e, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).