3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT8610ACIMSE#TRPBF
Analog Devices · DC-DC Converters · MSOP-16-EP
LT8610ACIMSE#TRPBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SYNC | input | External clock synchronization input: ground it for low-ripple Burst Mode at light load, apply a DC voltage of 3V or higher or tie to INTVCC for pulse-skipping mode, and do not float it. |
| 2 | TR/SS | bidirectional | Output tracking and soft-start pin where a voltage below 0.8V makes FB track it, with an internal 2.2µA pull-up from INTVCC and a 230Ω pull-down during shutdown and fault, and a minimum of 100pF is required on the LT8610AC-1. |
| 3 | RT | passive | A resistor connected between RT and ground sets the switching frequency. |
| 4 | EN/UV | input | The regulator is shut down when this pin is low and active when high, with a 1.015V rising and 0.97V falling threshold, and it must be tied to VIN if the shutdown feature is not used. |
| 5 | VIN | power_in | Supplies the internal circuitry and the top power switch; pins 5 and 6 must be tied together and locally bypassed, with absolute maximum rating of 42V. |
| 6 | VIN | power_in | Supplies the internal circuitry and the top power switch; must be tied together with pin 5 and locally bypassed, with absolute maximum rating of 42V. |
| 7 | NC | unconnected | No connect; this pin is not connected to internal circuitry. |
| 8 | GND | power_in | Ground return for the internal bottom-side switch that must be tied together with pin 17 and kept close to the input capacitor negative terminal. |
| 9 | SW | output | Output of the internal power switches; pins 9, 10 and 11 must be tied together and connected to the inductor and boost capacitor, with the node kept small on the PCB. |
| 10 | SW | output | Output of the internal power switches; must be tied together with pins 9 and 11 and connected to the inductor and boost capacitor. |
| 11 | SW | output | Output of the internal power switches; must be tied together with pins 9 and 10 and connected to the inductor and boost capacitor. |
| 12 | BST | power_out | Provides a drive voltage higher than the input voltage to the top power switch, with a 0.1µF boost capacitor placed as close to the IC as possible and a 4V absolute maximum rating above the SW pin. |
| 13 | INTVCC | power_out | Internal 3.4V regulator bypass pin with a maximum output current of 20mA that must not be loaded externally and needs at least a 1µF low-ESR ceramic capacitor to power ground. |
| 14 | BIAS | power_in | Supplies the internal regulator from BIAS instead of VIN when tied above 3.1V, should be tied to VOUT for outputs of 3.3V and above, and needs a 1µF bypass if supplied from another source, with a 30V absolute maximum rating. |
| 15 | PG | output | Open-drain power-good output that stays low until FB is within ±8% of the regulation voltage with no faults, and is valid when VIN is above 3.0V regardless of EN/UV state. |
| 16 | FB | input | Feedback input that regulates to 0.800V, connected to the feedback divider tap with a 4.7pF to 10pF phase lead capacitor to VOUT, with a 4V absolute maximum rating. |
| 17 | GND | power_in | Exposed pad is ground and must be soldered to the PCB to lower the thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | 2.6 | 3 | V | 2 | |||
| VIN Quiescent Current | 1 | 3 | µA | VEN/UV = 0V | 2 | ||
| VIN Quiescent Current (full operating temperature range) | 1 | 8 | µA | VEN/UV = 0V | 2 | ||
| VIN Quiescent Current, not switching | 1.7 | 4 | µA | VEN/UV = 2V, Not Switching, VSYNC = 0V | 2 | ||
| VIN Quiescent Current, not switching (full operating temperature range) | 1.7 | 10 | µA | VEN/UV = 2V, Not Switching, VSYNC = 0V | 2 | ||
| VIN Quiescent Current, pulse-skipping | 0.28 | 0.5 | mA | VEN/UV = 2V, Not Switching, VSYNC = 2V | 2 | ||
| VIN Current in Regulation | 30 | 60 | µA | VOUT = 0.8V, VIN = 6V, Output Load = 100µA | 3 | ||
| VIN Current in Regulation (full operating temperature range) | 225 | 500 | µA | VOUT = 0.8V, VIN = 6V, Output Load = 1mA | 3 | ||
| Feedback Reference Voltage | 0.794 | 0.8 | 0.806 | V | VIN = 6V, ILOAD = 0.5A | 3 | |
| Feedback Reference Voltage (full operating temperature range) | 0.788 | 0.8 | 0.812 | V | VIN = 6V, ILOAD = 0.5A | 3 | |
| Feedback Voltage Line Regulation | 0.004 | 0.02 | %/V | VIN = 4.0V to 42V, ILOAD = 1A | 3 | ||
| Feedback Pin Input Current | -20 | 20 | nA | VFB = 1V | 3 | ||
| INTVCC Voltage | 3.23 | 3.25 | 3.4 | V | ILOAD = 0mA, VBIAS = 0V | 3 | |
| INTVCC Voltage | 3.29 | 3.35 | 3.57 | V | ILOAD = 0mA, VBIAS = 3.3V | 3 | |
| INTVCC Undervoltage Lockout | 2.37 | 2.47 | 2.57 | V | 3 | ||
| Minimum On-Time | 15 | 30 | 45 | ns | ILOAD = 1A, SYNC = 0V | 3 | |
| Minimum Off-Time | 95 | 125 | ns | 3 | |||
| Oscillator Frequency | 180 | 210 | 240 | kHz | RT = 221k, ILOAD = 1A (LT8610AC Only) | 3 | |
| Oscillator Frequency | 665 | 700 | 735 | kHz | RT = 60.4k, ILOAD = 1A (LT8610AC Only) | 3 | |
| Oscillator Frequency | 1.85 | 2 | 2.15 | MHz | RT = 18.2k, ILOAD = 1A (LT8610AC/LT8610AC-1) | 3 | |
| Top Power NMOS Current Limit | 5 | 6.7 | 8 | A | 3 | ||
| Bottom Power NMOS Current Limit | 3.4 | 4.3 | 5.4 | A | VINTVCC = 3.4V | 3 | |
| SW Leakage Current | -1.5 | 1.5 | µA | VIN = 42V, VSW = 0V, 42V | 3 | ||
| EN/UV Pin Threshold | 0.955 | 1.015 | 1.075 | V | EN/UV Rising | 3 | |
| EN/UV Pin Current | -20 | 20 | nA | VEN/UV = 2V | 3 | ||
| PG Upper Threshold Offset from VFB | 5 | 8 | 11 | % | VFB Falling | 3 | |
| PG Lower Threshold Offset from VFB | -11 | -8 | -5 | % | VFB Rising | 3 | |
| PG Leakage | -40 | 40 | nA | VPG = 3.3V | 3 | ||
| PG Pull-Down Resistance | 680 | 2000 | Ω | VPG = 0.1V | 3 | ||
| SYNC Threshold (falling) | 0.8 | 1.1 | 1.4 | V | SYNC Falling | 3 | |
| SYNC Threshold (rising) | 1.6 | 2 | 2.4 | V | SYNC Rising | 3 | |
| TR/SS Source Current | 1 | 2 | 3.2 | µA | 3 | ||
| Operating Junction Temperature Range (LT8610ACI) | -40 | 125 | °C | 2 | |||
| VIN, EN/UV, PG Voltage | 42 | V | 2 | ||||
| BIAS Voltage | 30 | V | 2 | ||||
| BST Pin Above SW Pin | 4 | V | 2 | ||||
| FB, TR/SS, RT, INTVCC Voltage | 4 | V | 2 | ||||
| SYNC Voltage | 6 | V | 2 | ||||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| INTVCC Maximum Output Current | 20 | mA | 9 | ||||
| Junction-to-Ambient Thermal Resistance | θJA | 40 | °C/W | 2 | |||
| Junction-to-Case (Exposed Pad) Thermal Resistance | θJC(PAD) | 10 | °C/W | 2 |
CAD (KiCad official)
- Symbol:
LT8610ACIMSE#TRPBF - Footprint:
Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm - 3D model: MSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lt8610acimse-trpbf-etched.step/lt8610acimse-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8610acimse-trpbf.step/lt8610acimse-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (26 pp, sha256
dd42b6a8e79c0863, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).