Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT8610ACIMSE#TRPBF

Analog Devices · DC-DC Converters · MSOP-16-EP

LT8610ACIMSE#TRPBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SYNC input External clock synchronization input: ground it for low-ripple Burst Mode at light load, apply a DC voltage of 3V or higher or tie to INTVCC for pulse-skipping mode, and do not float it.
2 TR/SS bidirectional Output tracking and soft-start pin where a voltage below 0.8V makes FB track it, with an internal 2.2µA pull-up from INTVCC and a 230Ω pull-down during shutdown and fault, and a minimum of 100pF is required on the LT8610AC-1.
3 RT passive A resistor connected between RT and ground sets the switching frequency.
4 EN/UV input The regulator is shut down when this pin is low and active when high, with a 1.015V rising and 0.97V falling threshold, and it must be tied to VIN if the shutdown feature is not used.
5 VIN power_in Supplies the internal circuitry and the top power switch; pins 5 and 6 must be tied together and locally bypassed, with absolute maximum rating of 42V.
6 VIN power_in Supplies the internal circuitry and the top power switch; must be tied together with pin 5 and locally bypassed, with absolute maximum rating of 42V.
7 NC unconnected No connect; this pin is not connected to internal circuitry.
8 GND power_in Ground return for the internal bottom-side switch that must be tied together with pin 17 and kept close to the input capacitor negative terminal.
9 SW output Output of the internal power switches; pins 9, 10 and 11 must be tied together and connected to the inductor and boost capacitor, with the node kept small on the PCB.
10 SW output Output of the internal power switches; must be tied together with pins 9 and 11 and connected to the inductor and boost capacitor.
11 SW output Output of the internal power switches; must be tied together with pins 9 and 10 and connected to the inductor and boost capacitor.
12 BST power_out Provides a drive voltage higher than the input voltage to the top power switch, with a 0.1µF boost capacitor placed as close to the IC as possible and a 4V absolute maximum rating above the SW pin.
13 INTVCC power_out Internal 3.4V regulator bypass pin with a maximum output current of 20mA that must not be loaded externally and needs at least a 1µF low-ESR ceramic capacitor to power ground.
14 BIAS power_in Supplies the internal regulator from BIAS instead of VIN when tied above 3.1V, should be tied to VOUT for outputs of 3.3V and above, and needs a 1µF bypass if supplied from another source, with a 30V absolute maximum rating.
15 PG output Open-drain power-good output that stays low until FB is within ±8% of the regulation voltage with no faults, and is valid when VIN is above 3.0V regardless of EN/UV state.
16 FB input Feedback input that regulates to 0.800V, connected to the feedback divider tap with a 4.7pF to 10pF phase lead capacitor to VOUT, with a 4V absolute maximum rating.
17 GND power_in Exposed pad is ground and must be soldered to the PCB to lower the thermal resistance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-16-EP
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Minimum Input Voltage 2.6 3 V 2
VIN Quiescent Current 1 3 µA VEN/UV = 0V 2
VIN Quiescent Current (full operating temperature range) 1 8 µA VEN/UV = 0V 2
VIN Quiescent Current, not switching 1.7 4 µA VEN/UV = 2V, Not Switching, VSYNC = 0V 2
VIN Quiescent Current, not switching (full operating temperature range) 1.7 10 µA VEN/UV = 2V, Not Switching, VSYNC = 0V 2
VIN Quiescent Current, pulse-skipping 0.28 0.5 mA VEN/UV = 2V, Not Switching, VSYNC = 2V 2
VIN Current in Regulation 30 60 µA VOUT = 0.8V, VIN = 6V, Output Load = 100µA 3
VIN Current in Regulation (full operating temperature range) 225 500 µA VOUT = 0.8V, VIN = 6V, Output Load = 1mA 3
Feedback Reference Voltage 0.794 0.8 0.806 V VIN = 6V, ILOAD = 0.5A 3
Feedback Reference Voltage (full operating temperature range) 0.788 0.8 0.812 V VIN = 6V, ILOAD = 0.5A 3
Feedback Voltage Line Regulation 0.004 0.02 %/V VIN = 4.0V to 42V, ILOAD = 1A 3
Feedback Pin Input Current -20 20 nA VFB = 1V 3
INTVCC Voltage 3.23 3.25 3.4 V ILOAD = 0mA, VBIAS = 0V 3
INTVCC Voltage 3.29 3.35 3.57 V ILOAD = 0mA, VBIAS = 3.3V 3
INTVCC Undervoltage Lockout 2.37 2.47 2.57 V 3
Minimum On-Time 15 30 45 ns ILOAD = 1A, SYNC = 0V 3
Minimum Off-Time 95 125 ns 3
Oscillator Frequency 180 210 240 kHz RT = 221k, ILOAD = 1A (LT8610AC Only) 3
Oscillator Frequency 665 700 735 kHz RT = 60.4k, ILOAD = 1A (LT8610AC Only) 3
Oscillator Frequency 1.85 2 2.15 MHz RT = 18.2k, ILOAD = 1A (LT8610AC/LT8610AC-1) 3
Top Power NMOS Current Limit 5 6.7 8 A 3
Bottom Power NMOS Current Limit 3.4 4.3 5.4 A VINTVCC = 3.4V 3
SW Leakage Current -1.5 1.5 µA VIN = 42V, VSW = 0V, 42V 3
EN/UV Pin Threshold 0.955 1.015 1.075 V EN/UV Rising 3
EN/UV Pin Current -20 20 nA VEN/UV = 2V 3
PG Upper Threshold Offset from VFB 5 8 11 % VFB Falling 3
PG Lower Threshold Offset from VFB -11 -8 -5 % VFB Rising 3
PG Leakage -40 40 nA VPG = 3.3V 3
PG Pull-Down Resistance 680 2000 Ω VPG = 0.1V 3
SYNC Threshold (falling) 0.8 1.1 1.4 V SYNC Falling 3
SYNC Threshold (rising) 1.6 2 2.4 V SYNC Rising 3
TR/SS Source Current 1 2 3.2 µA 3
Operating Junction Temperature Range (LT8610ACI) -40 125 °C 2
VIN, EN/UV, PG Voltage 42 V 2
BIAS Voltage 30 V 2
BST Pin Above SW Pin 4 V 2
FB, TR/SS, RT, INTVCC Voltage 4 V 2
SYNC Voltage 6 V 2
Storage Temperature Range -65 150 °C 2
INTVCC Maximum Output Current 20 mA 9
Junction-to-Ambient Thermal Resistance θJA 40 °C/W 2
Junction-to-Case (Exposed Pad) Thermal Resistance θJC(PAD) 10 °C/W 2

CAD (KiCad official)

  • Symbol: LT8610ACIMSE#TRPBF
  • Footprint: Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm
  • 3D model: MSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: lt8610acimse-trpbf-etched.step / lt8610acimse-trpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8610acimse-trpbf.step / lt8610acimse-trpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (26 pp, sha256 dd42b6a8e79c0863, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF