Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

STM32H7R3V8T6

ST · Microcontroller Units (MCUs/MPUs/SOCs) · LQFP-100(14x14)

STM32H7R3V8T6 from ST, in a LQFP-100(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VBAT power_in Backup-domain supply, 1.2 V to 3.6 V.
2 PC13 bidirectional FT I/O supplied via the VSW power switch (3 mA max sink), output limited to 2 MHz with 30 pF max load; functions TAMP_IN1/TAMP_OUT2, RTC_OUT1/RTC_TS, WKUP3.
3 PC14-OSC32_IN bidirectional I/O supplied via VSW (output limited to 2 MHz, 30 pF) and OSC32_IN LSE crystal input.
4 PC15-OSC32_OUT bidirectional I/O supplied via VSW (output limited to 2 MHz, 30 pF) and OSC32_OUT LSE crystal output.
5 PH0-OSC_IN bidirectional FT_h I/O, also OSC_IN HSE oscillator input.
6 PH1-OSC_OUT bidirectional FT_h I/O, also OSC_OUT HSE oscillator output.
7 NRST input Bidirectional reset pin with embedded weak pull-up resistor.
8 VSS power_in Digital ground.
9 VDD power_in Main digital supply, 1.71 V to 3.6 V.
10 PC0 bidirectional FT_h I/O with GFXTIM_FCKCAL, SAI2_FS_B, FMC_NBL1 alternate functions and ADC12_INP10 analog input.
11 PC1 bidirectional FT_h I/O with SPI2_MOSI/I2S2_SDO, SAI1_SD_A, ETH_MDC alternate functions; ADC12_INP11/INN10, TAMP_IN7/TAMP_OUT8, WKUP4.
12 VSSA power_in Analog ground.
13 VREFM power_in Negative reference voltage for ADC/VREFBUF.
14 VREFP power_in Positive reference voltage for ADC/VREFBUF.
15 VDDA power_in Analog supply, 1.62 V to 3.6 V with ADC used (2.10 V min with VREFBUF).
16 PA0 bidirectional FT_h I/O with TIM2_CH1, TIM5_CH1, USART2_CTS, UART4_TX; ADC12_INP0/INN1, WKUP1.
17 PA1 bidirectional FT_h I/O with TIM2_CH2, TIM5_CH2, USART2_RTS, UART4_RX; ADC12_INP1.
18 PA2 bidirectional FT_h I/O with TIM2_CH3, USART2_TX, ETH_MDIO; ADC12_INP14, WKUP2.
19 PA3 bidirectional FT_h I/O with TIM2_CH4, TIM5_CH4, USART2_RX, LCD_DE; ADC12_INP15.
20 VSS power_in Digital ground.
21 PA4 bidirectional FT_h I/O with SPI1_NSS/I2S1_WS, SPI3_NSS, USART2_CK, DCMIPP_HSYNC; ADC1_INP18.
22 PA5 bidirectional FT_h I/O with PWR_CSTOP, TIM2_CH1, SPI1_SCK, LCD_CLK; ADC2_INP18.
23 VDD power_in Main digital supply, 1.71 V to 3.6 V.
24 PA6 bidirectional FT_h I/O with PWR_CSLEEP, TIM1_BKIN, TIM3_CH1, SPI1_MISO; ADC12_INP3.
25 PA7 bidirectional FT_h I/O with TIM1_CH1N, TIM3_CH2, SPI1_MOSI, ETH_MII_RX_DV; ADC12_INP7/INN3.
26 PB0 bidirectional FT_h I/O with TIM1_CH2N, TIM3_CH3, SPI1_SCK, UART4_CTS; ADC12_INP9/INN5.
27 PB1 bidirectional FT_h I/O with TIM1_CH3N, TIM3_CH4, FDCAN2_TX, FMC_NOE; ADC12_INP5.
28 PB2 bidirectional FT_h I/O with RTC_OUT2, SAI1_SD_A, SPI3_MOSI, FMC_NWE.
29 PO1 bidirectional FT_h I/O providing XSPIM_P1_NCS2.
30 VDDXSPI1 power_in Octo/Hexa-SPI port 1 I/O supply, 1.62 V to 3.6 V (HSLV=0).
31 VSS power_in Digital ground.
32 PP4 bidirectional FT_h I/O providing XSPIM_P1_IO4.
33 PP2 bidirectional FT_h I/O providing XSPIM_P1_IO2.
34 PP3 bidirectional FT_h I/O providing XSPIM_P1_IO3.
35 VSS power_in Digital ground.
36 VDDXSPI1 power_in Octo/Hexa-SPI port 1 I/O supply, 1.62 V to 3.6 V (HSLV=0).
37 PO5 bidirectional FT_h I/O providing XSPIM_P1_NCLK.
38 PO4 bidirectional FT_h I/O providing XSPIM_P1_CLK.
39 PP5 bidirectional FT_h I/O providing XSPIM_P1_IO5.
40 PP0 bidirectional FT_h I/O providing XSPIM_P1_IO0.
41 VSS power_in Digital ground.
42 VDDXSPI1 power_in Octo/Hexa-SPI port 1 I/O supply, 1.62 V to 3.6 V (HSLV=0).
43 PP6 bidirectional FT_h I/O providing XSPIM_P1_IO6.
44 PO2 bidirectional FT_h I/O providing XSPIM_P1_DQS0.
45 PP7 bidirectional FT_h I/O providing XSPIM_P1_IO7.
46 PP1 bidirectional FT_h I/O providing XSPIM_P1_IO1.
47 VSS power_in Digital ground.
48 VDDXSPI1 power_in Octo/Hexa-SPI port 1 I/O supply, 1.62 V to 3.6 V (HSLV=0).
49 PO0 bidirectional FT_h I/O providing XSPIM_P1_NCS1.
50 PB10 bidirectional FT_fh (Fm+) I/O with TIM2_CH3, I2C2_SCL, SPI2_SCK, USART3_TX, ETH_MII_RX_ER.
51 PB11 bidirectional FT_fh (Fm+) I/O with TIM2_CH4, I2C2_SDA, USART3_RX, ETH_MII_TX_EN.
52 PB12 bidirectional FT_h I/O with TIM1_BKIN, I2C2_SMBA, SPI2_NSS, USART3_CK, FDCAN2_RX.
53 PB13 bidirectional FT_h I/O with TIM1_CH1N, SPI2_SCK, SDMMC1_D0, USART3_CTS, FDCAN2_TX.
54 PB14 bidirectional FT_h I/O with TIM1_CH2N, USART1_TX, SPI2_MISO, USART3_RTS, SDMMC2_D0.
55 PB15 bidirectional FT_h I/O with RTC_REFIN, TIM1_CH3N, USART1_RX, SPI2_MOSI, SDMMC2_D1; PVD_IN.
56 VCAP2 passive Core regulator output; connect a 2.2 µF (±20%) capacitor with ESR below 100 mΩ.
57 VSS power_in Digital ground.
58 VDD power_in Main digital supply, 1.71 V to 3.6 V.
59 PA8 bidirectional FT_fh (Fm+) I/O with MCO1, TIM1_CH1, I2C3_SCL, USART1_CK, OTG_FS_SOF.
60 PA9 bidirectional FT_fh (Fm+) I/O with TIM1_CH2, LPUART1_TX, I2C3_SDA, SPI2_SCK, USART1_TX.
61 PA10 bidirectional FT_h I/O with TIM1_CH3, LPUART1_RX, USART1_RX, MDIOS_MDIO.
62 PA11 bidirectional FT_h I/O with TIM1_CH4, LPUART1_CTS, SPI2_NSS, UART4_RX, USART1_CTS, FDCAN1_RX.
63 PA12 bidirectional FT_h I/O with TIM1_ETR, LPUART1_RTS, SPI2_SCK, UART4_TX, USART1_RTS, FDCAN1_TX.
64 PA13 bidirectional FT_h I/O configured after reset as JTMS-SWDIO with internal pull-up active.
65 PA14 bidirectional FT_h I/O configured after reset as JTCK-SWCLK with internal pull-down active.
66 PA15(JTDI) bidirectional FT_h I/O configured after reset as JTDI with internal pull-up active; also TIM2_CH1, SPI1_NSS, HDMI_CEC.
67 VCAP3 passive Core regulator output; connect a 2.2 µF (±20%) capacitor with ESR below 100 mΩ.
68 VSS power_in Digital ground.
69 VDD power_in Main digital supply, 1.71 V to 3.6 V.
70 PC10 bidirectional FT_h I/O with TIM1_BKIN, SPI3_SCK, USART3_TX, UART4_TX, SDMMC1_D2.
71 PC11 bidirectional FT_h I/O with SPI3_MISO, USART3_RX, UART4_RX, SDMMC1_D3.
72 PC12 bidirectional FT_h I/O with TRACED3, SPI3_MOSI, USART3_CK, UART5_TX, SDMMC1_CK.
73 PM0 bidirectional FT_uc I/O providing UCPD_CC1; UCPD dead-battery 5.1 kΩ pull-down can be active after reset.
74 PM1 bidirectional FT_uc I/O providing UCPD_CC2; UCPD dead-battery 5.1 kΩ pull-down can be active after reset.
75 PM2 bidirectional FT_ud I/O providing UCPD_DB1 (dead-battery control for CC1).
76 PM3 bidirectional FT_ud I/O providing UCPD_DB2 (dead-battery control for CC2).
77 VDD50USB power_in USB regulator supply, 4.0 V to 5.5 V when the USB regulator is ON.
78 VDD33USB power_in USB supply, 3.0 V to 3.6 V when USB is used.
79 VSSUSB power_in USB ground.
80 PM5 bidirectional FT_u I/O providing OTG_HS_DM.
81 PM6 bidirectional FT_u I/O providing OTG_HS_DP.
82 DVDD power_in USB OTG_HS PHY digital supply, 0.95 V to 1.4 V.
83 PM8 bidirectional FT_u I/O with UART7_RX and OTG_HS_VBUS.
84 PM9 bidirectional FT_u I/O with UART7_TX and OTG_HS_ID.
85 VDD power_in Main digital supply, 1.71 V to 3.6 V.
86 PM12 bidirectional FT_u I/O with SPI5_NSS and OTG_FS_DM.
87 PM11 bidirectional FT_u I/O with SPI5_SCK and OTG_FS_DP.
88 PM14 bidirectional FT_u I/O with SPI5_MISO and OTG_FS_VBUS.
89 PM13 bidirectional FT_u I/O with SPI5_MOSI and OTG_FS_ID.
90 BOOT0 input Dedicated boot pin, input up to 9.0 V; additional function VPP.
91 PB3 bidirectional FT_h I/O with JTDO-SWO, TIM2_CH2, SPI1_SCK, SPI3_SCK, SDMMC2_D2.
92 PB4 bidirectional FT_h I/O configured after reset as NJTRST with internal pull-up active.
93 PB5 bidirectional FT_h I/O with TIM17_BKIN, TIM3_CH2, I2C1_SMBA, SPI1_MOSI, FDCAN2_RX.
94 VCAP4 passive Core regulator output; connect a 2.2 µF (±20%) capacitor with ESR below 100 mΩ.
95 VSS power_in Digital ground.
96 VDD power_in Main digital supply, 1.71 V to 3.6 V.
97 PB6 bidirectional FT_fh (Fm+) I/O with TIM16_CH1N, TIM4_CH1, I2C1_SCL/I3C1_SCL, USART1_TX, FDCAN2_TX.
98 PB7 bidirectional FT_fh (Fm+) I/O with TIM17_CH1N, TIM4_CH2, I2C1_SDA/I3C1_SDA, USART1_RX.
99 PB8 bidirectional FT_fh (Fm+) I/O with TIM16_CH1, TIM4_CH3, I2C1_SCL/I3C1_SCL, UART4_RX, FDCAN1_RX.
100 PB9 bidirectional FT_fh (Fm+) I/O with TIM17_CH1, TIM4_CH4, I2C1_SDA/I3C1_SDA, FDCAN1_TX; TAMP_IN2/TAMP_OUT1.

Key specifications

Parameter Value
Manufacturer ST
Package LQFP-100(14x14)
Category Embedded Processors & Controllers
Pins 100

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
External main supply voltage (VDD, VDDSMPS, VDDA, VDDUSB, VDDXSPIx, VBAT, VREF+) abs max VDDX-VSS -0.3 4 V 152
Input voltage on TT_xx pins VIN -0.3 4 V VSS-0.3 to 4.0 152
Input voltage on BOOT0 pin VIN 0 9 V VSS to 9.0 152
Total current into all VDD lines ΣIVDD 620 mA source 153
Total current out of all VSS lines ΣIVSS 620 mA sink 153
Max current per VDD pin IVDD 100 mA source 153
Max current per VSS pin IVSS 100 mA sink 153
Output current per I/O IIO 20 mA any I/O and control pin, except Pxy_C 153
Storage temperature TSTG -65 150 °C 153
Maximum junction temperature TJ 130 °C Industrial temperature range 6; limited to 105 °C in VOS high 153
Standard operating voltage VDD 1.71 3.6 V HSLV=0 154
Standard operating voltage VDD 1.71 2.7 V HSLV=1 154
Supply voltage for internal regulator VDDLDO 1.71 3.6 V 154
Supply voltage for SMPS VDDSMPS 1.71 3.6 V 154
Octo and HexaSPI supply VDDXSPIx 1.62 3.6 V HSLV=0 154
Octo and HexaSPI supply VDDXSPIx 1.08 2.7 V HSLV=1 154
USB supply voltage VDD50USB 4 5 5.5 V USB regulator ON 154
USB supply voltage VDD33USB 3 3.6 V USB used 154
Analog operating voltage VDDA 1.62 3.6 V ADC used 154
Analog operating voltage VDDA 2.1 3.6 V VREFBUF used 154
Backup domain supply voltage VBAT 1.2 3.6 V 154
BOOT0 input voltage VIN -0.3 9 V BOOT0 154
VCORE internal regulator ON VCORE 1.15 1.21 1.26 V VOS low 154
VCORE internal regulator ON VCORE 1.15 1.36 1.4 V VOS high 154
USB OTG_HS PHY digital supply voltage DVDD 0.95 1.4 V 154
CPU clock frequency fCPU 600 MHz VOS high (400 for VOS low) 155
Ambient temperature TA -40 85 °C Maximum power dissipation 155
Junction temperature TJ -40 105 °C VOS high 155
Junction temperature TJ -40 130 °C VOS low 155
POR/PDR threshold rising VBOR0/POR/PDR 1.62 1.67 1.71 V Rising edge 162
POR/PDR threshold falling VBOR0/POR/PDR 1.58 1.62 1.68 V Falling edge 162
Reset temporization tRSTTEMPO 377 550 µs after BOR0 released 162
Internal reference voltage VREFINT 1.18 1.216 1.255 V -40°C < TJ < TJmax 164
SMPS output voltage VOUT 1.62 1.8 1.98 V Iout=600 mA 158
SMPS input voltage VDDSMPS 2.3 3.6 V VOUT = 1.8 V 158
SMPS output current IOUT 600 mA External usage only 158
Run mode supply current, VOS high 600 MHz IDD 125 135 mA All peripherals disabled, ITCM, LDO, TJ = 25°C max 166

CAD (KiCad official)

  • Symbol: STM32H7R3V8T6
  • Footprint: Package_QFP:LQFP-100_14x14mm_P0.5mm
  • 3D model: LQFP-100(14x14) (KiCad packages3D, STEP)
  • 3D model files: stm32h7r3v8t6-etched.step / stm32h7r3v8t6-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm32h7r3v8t6.step / stm32h7r3v8t6.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: ST datasheet (321 pp, sha256 2a9876c2bb49d5c7, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF