Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

ESP32-C6

ESPRESSIF SYSTEMS · Microcontrollers (MCU/MPU/SOC) · QFN-40-EP(5x5)

ESP32-C6 from ESPRESSIF SYSTEMS, in a QFN-40-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 ANT bidirectional RF input and output pin for the antenna.
2 VDDA3P3 power_in Analog power domain supply input.
3 VDDA3P3 power_in Analog power domain supply input.
4 CHIP_PU input High enables the chip (powered up), low disables it (powered down); do not leave this pin floating.
5 VDDPST1 power_in Supplies the LP digital and part of the analog pin power domain (LP IO pins).
6 XTAL_32K_P bidirectional Positive 32 kHz clock signal connected to the external crystal or oscillator; also GPIO0 and ADC1_CH0.
7 XTAL_32K_N bidirectional Negative 32 kHz clock signal connected to the external crystal or oscillator; also GPIO1 and ADC1_CH1.
8 GPIO2 bidirectional General-purpose IO with LP IO MUX and analog function ADC1_CH2; also FSPIQ function.
9 GPIO3 bidirectional General-purpose IO with LP IO MUX and analog function ADC1_CH3.
10 MTMS bidirectional JTAG test mode select, also used as a strapping pin for SDIO sampling and driving clock edge; floating by default.
11 MTDI bidirectional JTAG test data input, also used as a strapping pin for SDIO sampling and driving clock edge; floating by default.
12 MTCK bidirectional JTAG test clock; input enabled with internal weak pull-up depending on EFUSE_DIS_PAD_JTAG.
13 MTDO bidirectional JTAG test data output, high impedance type O/T in the IO MUX function table.
14 GPIO8 bidirectional General-purpose IO and strapping pin for chip boot mode and ROM message printing; floating by default.
15 GPIO9 bidirectional General-purpose IO and strapping pin for chip boot mode; internal weak pull-up enabled by default.
16 GPIO10 bidirectional General-purpose IO pin with IO MUX function GPIO10.
17 GPIO11 bidirectional General-purpose IO pin with IO MUX function GPIO11.
18 GPIO12 bidirectional General-purpose IO that is also USB_D- of the USB Serial/JTAG controller; default drive strength 40 mA.
19 GPIO13 bidirectional General-purpose IO that is also USB_D+ of the USB Serial/JTAG controller; USB pull-up enabled by default.
20 SPICS0 bidirectional SPI flash chip select (CS#) for off-package flash; powered from VDD_SPI.
21 SPIQ bidirectional SPI flash data line MISO (SIO1) for off-package flash; powered from VDD_SPI.
22 SPIWP bidirectional SPI flash write protect (WP#, SIO2); powered from VDD_SPI and reserved for flash use.
23 VDD_SPI power_out Supplies in-package and off-package flash; can only be used as GPIO27 if flash is powered by an external supply.
24 SPIHD bidirectional SPI flash hold (HOLD#, SIO3) for off-package flash; powered from VDD_SPI.
25 SPICLK bidirectional SPI flash clock output for off-package flash; powered from VDD_SPI.
26 SPID bidirectional SPI flash data line MOSI (SIO0) for off-package flash; powered from VDD_SPI.
27 GPIO15 bidirectional General-purpose IO and strapping pin for JTAG signal source control; floating by default.
28 VDDPST2 power_in Supplies the HP digital power domain (HP IO pins).
29 U0TXD bidirectional UART0 transmit data output, output enabled, internal weak pull-up enabled.
30 U0RXD bidirectional UART0 receive data input with input enabled and internal weak pull-up enabled.
31 SDIO_CMD bidirectional SDIO interface command line, input enabled with internal weak pull-up at reset.
32 SDIO_CLK input SDIO interface clock input, input enabled with internal weak pull-up at reset.
33 SDIO_DATA0 bidirectional SDIO interface data line 0, input enabled with internal weak pull-up at reset.
34 SDIO_DATA1 bidirectional SDIO interface data line 1, input enabled with internal weak pull-up at reset.
35 SDIO_DATA2 bidirectional SDIO interface data line 2, input enabled with internal weak pull-up at reset.
36 SDIO_DATA3 bidirectional SDIO interface data line 3, input enabled with internal weak pull-up at reset.
37 VDDA1 power_in Analog power domain supply input.
38 XTAL_N passive External clock input/output connected to the chip crystal or oscillator; negative side of the differential clock.
39 XTAL_P passive External clock input/output connected to the chip crystal or oscillator; positive side of the differential clock.
40 VDDA2 power_in Analog power domain supply input.
41 GND power_in External ground connection.

Key specifications

Parameter Value
Manufacturer ESPRESSIF SYSTEMS
Package QFN-40-EP(5x5)
Category Embedded Processors & Controllers
Pins 41

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Allowed input voltage (input power pins) -0.3 3.6 V 64
Cumulative IO output current Ioutput 1000 mA 64
Storage temperature TSTORE -40 150 °C 64
VDDA1, VDDA2, VDDA3P3 recommended input voltage 3 3.3 3.6 V 64
VDDPST1 recommended input voltage 3 3.3 3.6 V 64
VDD_SPI (as input) recommended input voltage 3 3.3 3.6 V 64
VDDPST2 recommended input voltage 3 3.3 3.6 V 64
Cumulative input current IVDD 0.5 A 64
Ambient temperature TA -40 105 °C 64
High-level input current IIH 50 nA 65
Low-level input current IIL 50 nA 65
Differential nonlinearity (ADC) DNL -8 12 LSB 66
Integral nonlinearity (ADC) INL -10 10 LSB 66
ADC sampling rate 100 kSPS 66
ADC total error -12 12 mV ATTEN0, effective measurement range of 0 ~ 1000 66
ADC total error -23 23 mV ATTEN2, effective measurement range of 0 ~ 1900 66
ADC total error -40 40 mV ATTEN3, effective measurement range of 0 ~ 3300 66
RF transmit power range (802.15.4, 250 Kbps) -15 20 dBm 802.15.4 250 Kbps 77
Sensitivity @1% PER (802.15.4, 250 Kbps) -104 dBm 802.15.4 250 Kbps 77
Maximum received signal @1% PER (802.15.4, 250 Kbps) 8 dBm 802.15.4 250 Kbps 77
Sensitivity @30.8% PER -98.5 dBm Bluetooth LE 1 Mbps 75
Maximum received signal @30.8% PER 8 dBm Bluetooth LE 1 Mbps 75
Sensitivity @30.8% PER -95.5 dBm Bluetooth LE 2 Mbps 75
Sensitivity @30.8% PER -106 dBm Bluetooth LE 125 Kbps 76
Maximum received signal @30.8% PER 8 dBm Bluetooth LE 125 Kbps 76
Sensitivity @30.8% PER -102 dBm Bluetooth LE 500 Kbps 76
TX EVM limit EVM -10 dB 802.11b, 1 Mbps, DSSS 70
TX EVM limit EVM -5 dB 802.11g, 6 Mbps, OFDM 70
TX EVM limit EVM -25 dB 802.11g, 54 Mbps, OFDM 71
TX EVM limit EVM -5 dB 802.11n, HT20, MCS0 71
TX EVM limit EVM -27 dB 802.11n, HT20, MCS7 71
TX EVM limit EVM -32 dB 802.11ax, HE20, MCS9 71

CAD (KiCad official)

  • Symbol: ESP32-C6
  • Footprint: Package_DFN_QFN:QFN-40-1EP_5x5mm_P0.4mm_EP3.6x3.6mm
  • 3D model: QFN-40-EP(5x5) (KiCad packages3D, STEP)
  • 3D model files: esp32-c6-etched.step / esp32-c6-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); esp32-c6.step / esp32-c6.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: ESPRESSIF SYSTEMS datasheet (86 pp, sha256 372a5b42b2900c83, retrieved 2026-10-27, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF