component
ESP32-C6
Public Made by Adomby adom
ESPRESSIF SYSTEMS Microcontrollers (MCU/MPU/SOC), QFN-40-EP(5x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownESP32-C6
ESPRESSIF SYSTEMS · Microcontrollers (MCU/MPU/SOC) · QFN-40-EP(5x5)
ESP32-C6 from ESPRESSIF SYSTEMS, in a QFN-40-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | ANT | bidirectional | RF input and output pin for the antenna. |
| 2 | VDDA3P3 | power_in | Analog power domain supply input. |
| 3 | VDDA3P3 | power_in | Analog power domain supply input. |
| 4 | CHIP_PU | input | High enables the chip (powered up), low disables it (powered down); do not leave this pin floating. |
| 5 | VDDPST1 | power_in | Supplies the LP digital and part of the analog pin power domain (LP IO pins). |
| 6 | XTAL_32K_P | bidirectional | Positive 32 kHz clock signal connected to the external crystal or oscillator; also GPIO0 and ADC1_CH0. |
| 7 | XTAL_32K_N | bidirectional | Negative 32 kHz clock signal connected to the external crystal or oscillator; also GPIO1 and ADC1_CH1. |
| 8 | GPIO2 | bidirectional | General-purpose IO with LP IO MUX and analog function ADC1_CH2; also FSPIQ function. |
| 9 | GPIO3 | bidirectional | General-purpose IO with LP IO MUX and analog function ADC1_CH3. |
| 10 | MTMS | bidirectional | JTAG test mode select, also used as a strapping pin for SDIO sampling and driving clock edge; floating by default. |
| 11 | MTDI | bidirectional | JTAG test data input, also used as a strapping pin for SDIO sampling and driving clock edge; floating by default. |
| 12 | MTCK | bidirectional | JTAG test clock; input enabled with internal weak pull-up depending on EFUSE_DIS_PAD_JTAG. |
| 13 | MTDO | bidirectional | JTAG test data output, high impedance type O/T in the IO MUX function table. |
| 14 | GPIO8 | bidirectional | General-purpose IO and strapping pin for chip boot mode and ROM message printing; floating by default. |
| 15 | GPIO9 | bidirectional | General-purpose IO and strapping pin for chip boot mode; internal weak pull-up enabled by default. |
| 16 | GPIO10 | bidirectional | General-purpose IO pin with IO MUX function GPIO10. |
| 17 | GPIO11 | bidirectional | General-purpose IO pin with IO MUX function GPIO11. |
| 18 | GPIO12 | bidirectional | General-purpose IO that is also USB_D- of the USB Serial/JTAG controller; default drive strength 40 mA. |
| 19 | GPIO13 | bidirectional | General-purpose IO that is also USB_D+ of the USB Serial/JTAG controller; USB pull-up enabled by default. |
| 20 | SPICS0 | bidirectional | SPI flash chip select (CS#) for off-package flash; powered from VDD_SPI. |
| 21 | SPIQ | bidirectional | SPI flash data line MISO (SIO1) for off-package flash; powered from VDD_SPI. |
| 22 | SPIWP | bidirectional | SPI flash write protect (WP#, SIO2); powered from VDD_SPI and reserved for flash use. |
| 23 | VDD_SPI | power_out | Supplies in-package and off-package flash; can only be used as GPIO27 if flash is powered by an external supply. |
| 24 | SPIHD | bidirectional | SPI flash hold (HOLD#, SIO3) for off-package flash; powered from VDD_SPI. |
| 25 | SPICLK | bidirectional | SPI flash clock output for off-package flash; powered from VDD_SPI. |
| 26 | SPID | bidirectional | SPI flash data line MOSI (SIO0) for off-package flash; powered from VDD_SPI. |
| 27 | GPIO15 | bidirectional | General-purpose IO and strapping pin for JTAG signal source control; floating by default. |
| 28 | VDDPST2 | power_in | Supplies the HP digital power domain (HP IO pins). |
| 29 | U0TXD | bidirectional | UART0 transmit data output, output enabled, internal weak pull-up enabled. |
| 30 | U0RXD | bidirectional | UART0 receive data input with input enabled and internal weak pull-up enabled. |
| 31 | SDIO_CMD | bidirectional | SDIO interface command line, input enabled with internal weak pull-up at reset. |
| 32 | SDIO_CLK | input | SDIO interface clock input, input enabled with internal weak pull-up at reset. |
| 33 | SDIO_DATA0 | bidirectional | SDIO interface data line 0, input enabled with internal weak pull-up at reset. |
| 34 | SDIO_DATA1 | bidirectional | SDIO interface data line 1, input enabled with internal weak pull-up at reset. |
| 35 | SDIO_DATA2 | bidirectional | SDIO interface data line 2, input enabled with internal weak pull-up at reset. |
| 36 | SDIO_DATA3 | bidirectional | SDIO interface data line 3, input enabled with internal weak pull-up at reset. |
| 37 | VDDA1 | power_in | Analog power domain supply input. |
| 38 | XTAL_N | passive | External clock input/output connected to the chip crystal or oscillator; negative side of the differential clock. |
| 39 | XTAL_P | passive | External clock input/output connected to the chip crystal or oscillator; positive side of the differential clock. |
| 40 | VDDA2 | power_in | Analog power domain supply input. |
| 41 | GND | power_in | External ground connection. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | ESPRESSIF SYSTEMS |
| Package | QFN-40-EP(5x5) |
| Category | Embedded Processors & Controllers |
| Pins | 41 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Allowed input voltage (input power pins) | -0.3 | 3.6 | V | 64 | |||
| Cumulative IO output current | Ioutput | 1000 | mA | 64 | |||
| Storage temperature | TSTORE | -40 | 150 | °C | 64 | ||
| VDDA1, VDDA2, VDDA3P3 recommended input voltage | 3 | 3.3 | 3.6 | V | 64 | ||
| VDDPST1 recommended input voltage | 3 | 3.3 | 3.6 | V | 64 | ||
| VDD_SPI (as input) recommended input voltage | 3 | 3.3 | 3.6 | V | 64 | ||
| VDDPST2 recommended input voltage | 3 | 3.3 | 3.6 | V | 64 | ||
| Cumulative input current | IVDD | 0.5 | A | 64 | |||
| Ambient temperature | TA | -40 | 105 | °C | 64 | ||
| High-level input current | IIH | 50 | nA | 65 | |||
| Low-level input current | IIL | 50 | nA | 65 | |||
| Differential nonlinearity (ADC) | DNL | -8 | 12 | LSB | 66 | ||
| Integral nonlinearity (ADC) | INL | -10 | 10 | LSB | 66 | ||
| ADC sampling rate | 100 | kSPS | 66 | ||||
| ADC total error | -12 | 12 | mV | ATTEN0, effective measurement range of 0 ~ 1000 | 66 | ||
| ADC total error | -23 | 23 | mV | ATTEN2, effective measurement range of 0 ~ 1900 | 66 | ||
| ADC total error | -40 | 40 | mV | ATTEN3, effective measurement range of 0 ~ 3300 | 66 | ||
| RF transmit power range (802.15.4, 250 Kbps) | -15 | 20 | dBm | 802.15.4 250 Kbps | 77 | ||
| Sensitivity @1% PER (802.15.4, 250 Kbps) | -104 | dBm | 802.15.4 250 Kbps | 77 | |||
| Maximum received signal @1% PER (802.15.4, 250 Kbps) | 8 | dBm | 802.15.4 250 Kbps | 77 | |||
| Sensitivity @30.8% PER | -98.5 | dBm | Bluetooth LE 1 Mbps | 75 | |||
| Maximum received signal @30.8% PER | 8 | dBm | Bluetooth LE 1 Mbps | 75 | |||
| Sensitivity @30.8% PER | -95.5 | dBm | Bluetooth LE 2 Mbps | 75 | |||
| Sensitivity @30.8% PER | -106 | dBm | Bluetooth LE 125 Kbps | 76 | |||
| Maximum received signal @30.8% PER | 8 | dBm | Bluetooth LE 125 Kbps | 76 | |||
| Sensitivity @30.8% PER | -102 | dBm | Bluetooth LE 500 Kbps | 76 | |||
| TX EVM limit | EVM | -10 | dB | 802.11b, 1 Mbps, DSSS | 70 | ||
| TX EVM limit | EVM | -5 | dB | 802.11g, 6 Mbps, OFDM | 70 | ||
| TX EVM limit | EVM | -25 | dB | 802.11g, 54 Mbps, OFDM | 71 | ||
| TX EVM limit | EVM | -5 | dB | 802.11n, HT20, MCS0 | 71 | ||
| TX EVM limit | EVM | -27 | dB | 802.11n, HT20, MCS7 | 71 | ||
| TX EVM limit | EVM | -32 | dB | 802.11ax, HE20, MCS9 | 71 |
CAD (KiCad official)
- Symbol:
ESP32-C6 - Footprint:
Package_DFN_QFN:QFN-40-1EP_5x5mm_P0.4mm_EP3.6x3.6mm - 3D model: QFN-40-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
esp32-c6-etched.step/esp32-c6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);esp32-c6.step/esp32-c6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: ESPRESSIF SYSTEMS datasheet (86 pp, sha256
372a5b42b2900c83, retrieved 2026-10-27, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).