component
MIC39102M
Public Made by Adomby adom
HGSEMI Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, SOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMIC39102M
HGSEMI · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · SOP-8
MIC39102M from HGSEMI, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Enable input is CMOS/TTL compatible: logic high enables the regulator, while logic low or open shuts it down, and EN may be tied directly to VIN and pulled up to the maximum supply voltage of 16V (absolute maximum +20V). |
| 2 | IN | power_in | Supply input, specified for 2.25V to 16V with an absolute maximum of 20V, and bypass with a 1µF or greater capacitor when the supply is a battery or more than 10 cm from bulk supply capacitance. |
| 3 | OUT | power_out | Regulator output, which requires an output capacitor (10µF or greater with ESR below 2Ω) for stability and needs a minimum load current of 10mA for proper regulation. |
| 4 | ADJ | input | Adjustment feedback input (MIC39102 only) that connects to a resistive divider between OUT and GND, setting VOUT = 1.240V × (R1/R2) over a 1.24V to 16V range with a typical bias current of 40 nA. |
| 5 | GND | power_in | Ground connection; pins 5 through 8 are all ground and should be connected together to the system ground. |
| 6 | GND | power_in | Ground connection; pins 5 through 8 are all ground and should be connected together to the system ground. |
| 7 | GND | power_in | Ground connection; pins 5 through 8 are all ground and should be connected together to the system ground. |
| 8 | GND | power_in | Ground connection; pins 5 through 8 are all ground and should be connected together to the system ground. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | HGSEMI |
| Package | SOP-8 |
| Category | Power Management (PMIC) |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VIN | -20 | 20 | V | 3 | ||
| Enable voltage | VEN | 20 | V | 3 | |||
| Storage temperature | TSTG | -65 | 150 | ℃ | 3 | ||
| Lead temperature | TL | 245 | ℃ | soldering, 10 sec. | 3 | ||
| Supply voltage | VIN | 2.25 | 16 | V | 4 | ||
| Enable voltage | VEN | 2.25 | 16 | V | 4 | ||
| Junction temperature | TJ | -40 | 125 | ℃ | 4 | ||
| Output voltage accuracy | VOUT | -1 | 1 | % | 10mA | 4 | |
| Output voltage accuracy | VOUT | -2 | 2 | % | 10mA ≤ IOUT ≤ 1A, VOUT+1V ≤ VIN ≤ 8V | 4 | |
| Line regulation | LNR | 0.06 | 0.5 | % | IOUT = 10mA, VOUT+1V ≤ VIN ≤ 16V | 4 | |
| Load regulation | LDR | 0.2 | 1 | % | VIN = VOUT+1V, 10mA ≤ IOUT ≤ 1A | 4 | |
| Dropout voltage | VDO | 150 | 250 | mV | IOUT = 100mA, VOUT = -1% | 4 | |
| Dropout voltage | VDO | 330 | 500 | mV | IOUT=750mA, VOUT = -1% | 4 | |
| Dropout voltage | VDO | 410 | 630 | mV | IOUT = 1A, VOUT = -1% | 4 | |
| Ground current | IGND | 12 | 20 | mA | IOUT = 1A, VIN = VOUT+1V | 4 | |
| Current limit | IOUT(lim) | 1.8 | 2.5 | µA | VOUT = 0V, VIN = VOUT+1V | 4 | |
| Turn-on time | tON | 1.3 | 5 | ms | 4 | ||
| Enable input voltage logic low (off) | VEN | 0.8 | V | Logic Low (off) | 4 | ||
| Enable input voltage logic high (on) | VEN | 2.25 | V | Logic High (on) | 4 | ||
| Enable input current | IEN | 1 | 15 | µA | VEN=2.25V | 4 | |
| Enable input current | IEN | 2 | 4 | µA | VEN=0.8V | 4 | |
| Flag output leakage current | IFLG(leak) | 0.01 | 2 | µA | VOH = 16V | 4 | |
| Flag output low voltage | VFLG(do) | 240 | 400 | mV | VIN = 0.9 x VOUT (Nominal), IOL= 250µA | 4 | |
| Reference voltage | VREF | 1.215 | 1.24 | 1.265 | V | 5 | |
| Reference voltage (Note 9 range) | VREF | 1.203 | 1.277 | V | Note 9 | 5 | |
| ADJ pin bias current | IADJ | 40 | 120 | nA | 5 | ||
| ADJ pin bias current temperature coefficient | 0.1 | 99.2 | nA/℃ | 5 | |||
| Output voltage temperature coefficient | ∆VOUT/∆T | 40 | 100 | ppm/℃ | 4 | ||
| Dropout voltage | VDO | 275 | mV | IOUT = 500mA, VOUT = -1% | 4 | ||
| Ground current | IGND | 700 | µA | IOUT = 100mA, VIN = VOUT+1V | 4 | ||
| Ground current | IGND | 4 | mA | IOUT = 500mA, VIN = VOUT+1V | 4 | ||
| Ground current | IGND | 7 | mA | IOUT = 750mA, VIN = VOUT+1V | 4 | ||
| Flag low threshold | VFLG | 93 | % | 4 | |||
| Flag high threshold | VFLG | 99.2 | % | 4 | |||
| Flag hysteresis | 1 | 4 | |||||
| Reference voltage temperature coefficient | 20 | ppm/℃ | 5 | ||||
| Thermal resistance junction-to-case, SOP-8 | θJC | 20 | ℃/W | 4 |
CAD (KiCad official)
- Symbol:
MIC39102M - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
mic39102m-etched.step/mic39102m-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic39102m.step/mic39102m.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: HGSEMI datasheet (12 pp, sha256
231b4f6360480038, retrieved 2026-10-19, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).