3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMT25QL128ABA8ESF-0SIT
Micron Tech · NOR FLASH · SOP-16-300mil
MT25QL128ABA8ESF-0SIT from Micron Tech, in a SOP-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DQ3/HOLD# | bidirectional | Serial I/O DQ3 shared with HOLD#, which pauses serial communication without deselecting or resetting the device (HOLD# is disabled in QIO-SPI mode or DTR operation); DQ3 must be driven HIGH or pulled up when using single/dual I/O commands. |
| 2 | VCC | power_in | Core and I/O power supply, 2.7 V to 3.6 V operating range. |
| 3 | RESET# | input | Active-low hardware reset that tri-states outputs and resets the device (data may be lost if driven LOW during a write, program or erase); it has an internal pull-up and may be left unconnected if unused. |
| 4 | DNU | unconnected | Do not use: must be left floating and not connected to any other signal or power supply. |
| 5 | DNU | unconnected | Do not use: must be left floating and not connected to any other signal or power supply. |
| 6 | DNU | unconnected | Do not use: must be left floating and not connected to any other signal or power supply. |
| 7 | S# | input | Chip select: HIGH puts the device in standby and tri-states outputs, LOW enables it, and a falling edge is required before any command after power-up. |
| 8 | DQ1 | bidirectional | Serial I/O DQ1: serial data output in legacy x1 extended SPI, bidirectional in dual and quad modes. |
| 9 | W#/DQ2 | bidirectional | Write protect input that freezes the status register when the status register write-disable bit is 1 and W# is LOW, or DQ2 I/O in quad modes; it has no internal pull-up, cannot be left floating and must be driven. |
| 10 | VSS | power_in | Core and I/O ground connection. |
| 11 | DNU | unconnected | Do not use: must be left floating and not connected to any other signal or power supply. |
| 12 | DNU | unconnected | Do not use: must be left floating and not connected to any other signal or power supply. |
| 13 | DNU | unconnected | Do not use: must be left floating and not connected to any other signal or power supply. |
| 14 | DNU | unconnected | Do not use: must be left floating and not connected to any other signal or power supply. |
| 15 | DQ0 | bidirectional | Serial I/O DQ0: serial data input in legacy x1 extended SPI, bidirectional in dual and quad modes. |
| 16 | C | input | Serial clock: command inputs latch on the rising edge, in STR data is output on the falling edge, and in DTR data is latched and output on both edges; maximum 133 MHz STR, 90 MHz DTR. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Micron Tech |
| Package | SOP-16-300mil |
| Category | Memory |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage temperature | TSTG | -65 | 150 | °C | 81 | ||
| Supply voltage | VCC | -0.6 | 4 | V | 81 | ||
| Input/output voltage with respect to ground | VIO | -0.6 | V | 81 | |||
| Electrostatic discharge voltage (human body model) | VESD | -2000 | 2000 | V | JESD22-A114A (C1=100pF, R1=1500Ω, R2=500Ω) | 81 | |
| Supply voltage | VCC | 2.7 | 3.6 | V | 81 | ||
| Ambient operating temperature | TA | -40 | 85 | °C | IT range | 81 | |
| Input/output capacitance (DQ0/DQ1/DQ2/DQ3) | CIN/OUT | 10 | pF | JEP147 VNA, VBIAS=VCC/2, TA=25°C, f=54 MHz | 81 | ||
| Input capacitance (other pins) | CIN | 6 | pF | JEP147 VNA, VBIAS=VCC/2, TA=25°C, f=54 MHz | 81 | ||
| Input/chip select capacitance | CIN/S# | 10 | pF | JEP147 VNA, VBIAS=VCC/2, TA=25°C, f=54 MHz | 81 | ||
| Input leakage current | ILI | -2 | 2 | µA | 83 | ||
| Output leakage current | ILO | -2 | 2 | µA | 83 | ||
| Standby current (IT range) | ICC1 | 15 | 50 | µA | S#=VCC, VIN=VSS or VCC | 83 | |
| Deep power-down current (IT range) | ICC2 | 5 | 30 | µA | S#=VCC, VIN=VSS or VCC | 83 | |
| Operating current (fast-read extended I/O) | ICC3 | 16 | mA | C=0.1VCC/0.9VCC at 133 MHz, DQ1 open | 83 | ||
| Operating current (fast-read extended I/O) | ICC3 | 8 | mA | C=0.1VCC/0.9VCC at 54 MHz, DQ1 open | 83 | ||
| Operating current (fast-read dual I/O) | ICC3 | 20 | mA | C=0.1VCC/0.9VCC at 133 MHz, DQ1 open | 83 | ||
| Operating current (fast-read quad I/O) | ICC3 | 22 | mA | C=0.1VCC/0.9VCC at 133 MHz, DQ1 open | 83 | ||
| Operating current (DTR) | ICC3 | 28 | mA | C=0.1VCC/0.9VCC at 80 MHz DTR, DQ open | 83 | ||
| Operating current (DTR) | ICC3 | 31 | mA | C=0.1VCC/0.9VCC at 90 MHz DTR, DQ open | 83 | ||
| Operating current (PROGRAM operations) | ICC4 | 35 | mA | S#=VCC | 83 | ||
| Operating current (WRITE operations) | ICC5 | 35 | mA | S#=VCC | 83 | ||
| Operating current (erase) | ICC6 | 35 | mA | S#=VCC | 83 | ||
| Input low voltage | VIL | -0.5 | V | 83 | |||
| Output low voltage | VOL | 0.4 | V | IOL=1.6mA | 84 | ||
| Clock frequency for all commands other than READ | fC | 133 | MHz | STR | 85 | ||
| Clock frequency for all commands other than READ | fC | 90 | MHz | DTR | 85 | ||
| Clock frequency for READ command (03h) | fR | 54 | MHz | STR | 85 | ||
| Clock frequency for READ command (03h) | fR | 27 | MHz | DTR | 85 | ||
| Clock HIGH time | tCH | 3.375 | ns | STR | 85 | ||
| Clock LOW time | tCL | 3.375 | ns | STR | 85 | ||
| Clock rise time (peak-to-peak) | tCLCH | 0.1 | V/ns | STR/DTR | 85 | ||
| Clock fall time (peak-to-peak) | tCHCL | 0.1 | V/ns | STR/DTR | 85 | ||
| S# active setup time (relative to clock) | tSLCH | 3.375 | ns | STR/DTR | 85 | ||
| S# not active hold time (relative to clock) | tCHSL | 3.375 | ns | STR/DTR | 85 | ||
| Data in setup time | tDVCH | 1.75 | ns | STR | 85 | ||
| Data in setup time | tDVCH | 1.5 | ns | DTR | 85 | ||
| Data in hold time | tCHDX | 2.3 | ns | STR/DTR | 85 | ||
| S# active hold time (relative to clock) | tCHSH | 3.375 | ns | STR | 85 | ||
| S# not active setup time (relative to clock) | tSHCH | 3.375 | ns | STR | 85 | ||
| S# deselect time after a READ command | tSHSL1 | 20 | ns | STR/DTR | 85 | ||
| S# deselect time after a nonREAD command | tSHSL2 | 50 | ns | STR/DTR, nonREAD commands | 85 | ||
| Output disable time | tSHQZ | 7 | ns | STR/DTR | 85 | ||
| Clock LOW to output valid | tCLQV | 6 | ns | STR/DTR, under 30pF | 85 | ||
| Clock LOW to output valid | tCLQV | 5 | ns | STR/DTR, under 10pF | 85 | ||
| Output hold time | tCLQX | 1.5 | ns | STR/DTR | 85 | ||
| HOLD setup time (relative to clock) | tHLCH | 3.375 | ns | STR/DTR | 85 | ||
| HOLD hold time (relative to clock) | tCHHH | 3.375 | ns | STR/DTR | 85 | ||
| HOLD to output Low-Z | tHHQX | 8 | ns | STR/DTR | 86 | ||
| HOLD to output High-Z | tHLQZ | 8 | ns | STR/DTR | 86 | ||
| Write protect setup time | tWHSL | 20 | ns | STR/DTR, applies when STATUS REGISTER WRITE is set to 1 | 86 | ||
| Write protect hold time | tSHWL | 100 | ns | STR/DTR, applies when STATUS REGISTER WRITE is set to 1 | 86 | ||
| S# HIGH to deep power-down | tDP | 3 | µs | STR/DTR | 86 | ||
| S# HIGH to standby mode (DPD exit time) | tRDP | 30 | µs | STR/DTR | 86 | ||
| WRITE STATUS REGISTER cycle time | tW | 1.3 | 8 | ms | STR/DTR | 86 | |
| Page program time (256 bytes) | tPP | 120 | 1800 | µs | STR/DTR, 256 bytes | 86 | |
| Sector erase time | tSE | 0.15 | 1 | s | STR/DTR | 86 | |
| 4KB subsector erase time | tSSE | 0.05 | 0.4 | s | STR/DTR | 86 | |
| 128Mb bulk erase time | tBE | 38 | 114 | s | STR/DTR | 86 | |
| Reset pulse width | tRLRH | 50 | ns | 87 | |||
| Reset recovery time | tRHSL | 40 | ns | device deselected (S# HIGH) and in standby mode | 87 |
CAD (KiCad official)
- Symbol:
MT25QL128ABA8ESF-0SIT - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOP-16-300mil (KiCad packages3D, STEP)
- 3D model files:
mt25ql128aba8esf-0sit-etched.step/mt25ql128aba8esf-0sit-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mt25ql128aba8esf-0sit.step/mt25ql128aba8esf-0sit.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Micron Tech datasheet (93 pp, sha256
1cbf328ecd1ee6f0, retrieved 2026-11-13, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).