3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownAL1792AFE-13
Diodes Incorporated · LED Drivers · UDFN-14-EP(4x3)
AL1792AFE-13 from Diodes Incorporated, in a UDFN-14-EP(4x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Active-high enable, internally pulled down; the device is enabled when EN is above about 2.5 V and disabled when it is below 0.4 V. |
| 2 | GND | power_in | Ground on the AL1792 (printed as PWM4/GND; PWM4 is only used on the AL1794). |
| 3 | GND | power_in | Ground on the AL1792 (printed as PWM3/GND; PWM3 is only used on the AL1793 and AL1794). |
| 4 | PWM2 | input | PWM signal input for channel 2 on the AL1792, internally pulled down; logic high needs at least 2.5 V and logic low is 0.4 V or below. |
| 5 | PWM1 | input | PWM signal input for channel 1, internally pulled down; tie to GND when channel 1 is not used. |
| 6 | LED1 | output | Channel 1 LED cathode and current-sink output; recommended maximum channel current is 0.5 A for the AL1792. |
| 7 | LED2 | output | Channel 2 LED cathode and current-sink output on the AL1792; recommended maximum channel current is 0.5 A. |
| 8 | GND | power_in | Ground. |
| 9 | GND | power_in | Ground on the AL1792 (printed as LED3/GND; LED3 is only used on the AL1793 and AL1794). |
| 10 | GND | power_in | Ground on the AL1792 (printed as LED4/GND; LED4 is only used on the AL1794). |
| 11 | LEDPG | output | LED power-good output, asserted low to report insufficient LED headroom; it needs an external pull-up resistor. |
| 12 | FAULTB | output | Open-drain fault report output, asserted low for UVLO, over-temperature, LED open or LED short; it needs an external pull-up resistor. |
| 13 | REF | passive | Reference current setting pin; an external RSET resistor sets the channel currents (VREF typically 1.5 V). |
| 14 | VIN | power_in | Voltage input, 6.5 V to 30 V recommended operating range with 30 V absolute maximum. |
| 15 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Diodes Incorporated |
| Package | UDFN-14-EP(4x3) |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 15 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage | VIN | 30 | V | TA=+25°C | 7 | ||
| Enable Voltage, PWM Voltage | VEN, VPWMx | 7 | V | TA=+25°C | 7 | ||
| Maximum Junction Temperature | TJ(MAX) | 160 | °C | 7 | |||
| Storage Temperature Range | TST | -65 | 150 | °C | 7 | ||
| Input voltage at VIN | VIN | 6.5 | 30 | V | 7 | ||
| Operating Ambient Temperature | TA | -40 | 125 | °C | 7 | ||
| High-Level Input Voltage on EN and PWMx | VIH | 2.5 | 5.5 | V | 7 | ||
| Low-Level Input Voltage on EN and PWMx | VIL | 0 | 0.4 | V | 7 | ||
| EN Low Voltage | VIL(EN) | 0 | 0.4 | V | 8 | ||
| EN High Voltage | VIH(EN) | 2.5 | V | 8 | |||
| EN Internal Pulldown | I(EN-PD) | 0.35 | 3.5 | μA | VEN=5V | 8 | |
| Digital PWM Low Voltage | VIL(PWMx) | 0.3 | V | 8 | |||
| Digital PWM High Voltage | VIH(PWMx) | 2.5 | V | 8 | |||
| Digital PWM Frequency | FPWMx | 0.5 | 4 | KHz | 8 | ||
| PWM Internal Pulldown | I(PWMx-PD) | 0.35 | 3.5 | μA | VEN=5V | 8 | |
| Reference Voltage | VREF | 1.47 | 1.5 | 1.53 | V | 8 | |
| LEDx Leakage Current | ILED_LEAK | 0.1 | 2 | μA | VPWMx=0V, VLEDx=+12V | 8 | |
| LED Current Accuracy | ILED_ACCURACY | -4 | 4 | % | RSET=12KΩ | 8 | |
| FAULTB Output Low Voltage | VFOL | 180 | mV | IFAULTB=1mA | 8 | ||
| FAULTB Leakage Current | IFOH | 1 | μA | VFAULTB=6V | 8 | ||
| UVLO Voltage | VUVLO | 6.3 | V | VIN Rising | 8 | ||
| UVLO Hysteresis | VUVHYS | 300 | mV | VIN Falling | 8 | ||
| Shutdown Supply Current | ISHDN | 10 | µA | Disabled | 8 | ||
| Quiescent Supply Current | IQ | 2 | mA | Enabled, LEDx floating, PWMx are "L", RSET is 12KΩ | 8 | ||
| Regulation Current for Channel 1 | ILED1_NOM | 250 | mA | RSET=12KΩ | 8 | ||
| Regulation Current for Channel 2 | ILED2_NOM | 250 | mA | RSET=12KΩ | 8 | ||
| Minimum LED Regulation Voltage | VLED_REG | 250 | mV | ILED1=250mA | 8 | ||
| Thermal Shutdown Threshold | TSHDN | 160 | °C | RSET=12KΩ | 8 | ||
| Thermal Resistance Junction-to-Ambient | θJA | 55 | °C/W | U-DFN4030-14 (Note 5) | 8 | ||
| Thermal Resistance Junction-to-Case | θJC | 12 | °C/W | U-DFN4030-14 (Note 5) | 8 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
AL1792AFE-13 - Footprint:
Package_DFN_QFN:DFN-14-1EP_3x4mm_P0.5mm_EP1.7x3.3mm - 3D model: UDFN-14-EP(4x3), generated on the KiCad land (body 3 x 4 mm, terminals on the pads, 0.6 mm tall, datasheet A, nominal). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
al1792afe-13-etched.step/al1792afe-13-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);al1792afe-13.step/al1792afe-13.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Diodes Incorporated datasheet (18 pp, sha256
b00e0b817e901edf, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).