Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MAX38909ATD+

Maxim Integrated · Linear Voltage Regulators (LDO) · TDFN-14(3x3)

MAX38909ATD+ from Maxim Integrated, in a TDFN-14(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 IN power_in Regulator supply input, to be connected to a voltage between 0.9V and 5.5V and bypassed with a 22μF ceramic capacitor from IN to GND.
2 IN power_in Regulator supply input, to be connected to a voltage between 0.9V and 5.5V and bypassed with a 22μF ceramic capacitor from IN to GND.
3 IN power_in Regulator supply input, to be connected to a voltage between 0.9V and 5.5V and bypassed with a 22μF ceramic capacitor from IN to GND.
4 IN power_in Regulator supply input, to be connected to a voltage between 0.9V and 5.5V and bypassed with a 22μF ceramic capacitor from IN to GND.
5 BIAS power_in Bias supply input, to be connected to a voltage between 2.7V and 20V and bypassed with a 1μF capacitor to GND, and must be at least 2.0V above the VOUT target.
6 EN input Enable input: a logic high (VEN high) enables the regulator output and a logic low (VEN low) disables it, and it can be tied to BIAS to keep the output always enabled.
7 GND power_in Regulator ground, to which the IN and OUT bypass capacitor grounds should be returned for best performance.
8 POK output Open-drain power-OK (power-on reset) output that requires a pullup resistor (10kΩ to 100kΩ) to an external supply and goes high once the output reaches its regulation target.
9 FB input Output voltage feedback input, connected to a resistor divider across OUT and GND with its center tap at this pin to set any output voltage between 0.6V and 5.0V.
10 BYP input Bypass capacitor input, to which a 0.001μF to 0.1μF capacitor is connected between OUT and BYP to reduce output noise and set the soft-start rate.
11 OUT power_out Regulator output that sources up to 2A at the regulation voltage, is bypassed with a 22μF ceramic capacitor to GND, and is pulled low through 70Ω when the regulator is disabled.
12 OUT power_out Regulator output that sources up to 2A at the regulation voltage, is bypassed with a 22μF ceramic capacitor to GND, and is pulled low through 70Ω when the regulator is disabled.
13 OUT power_out Regulator output that sources up to 2A at the regulation voltage, is bypassed with a 22μF ceramic capacitor to GND, and is pulled low through 70Ω when the regulator is disabled.
14 OUT power_out Regulator output that sources up to 2A at the regulation voltage, is bypassed with a 22μF ceramic capacitor to GND, and is pulled low through 70Ω when the regulator is disabled.
15 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Maxim Integrated
Package TDFN-14(3x3)
Category Power Supply Chip
Pins 15

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Voltage Range VIN 0.9 5.5 V Guaranteed by output accuracy, VOUT < VIN - VDO 6
Bias Voltage Range VBIAS 2.7 20 V 7
Input Undervoltage Lockout VIN_UVLO 0.35 0.45 0.55 V VIN rising, 60mV hysteresis 7
Bias Undervoltage Lockout VBIAS_UVLO 2.45 2.55 2.65 V VBIAS rising, 100mV hysteresis 7
Output Voltage Range VOUT 0.6 5 V Guaranteed by output accuracy 7
Output Capacitance COUT 10 22 μF Effective capacitance required for stability and proper operation 7
Input Supply Current IQ 70.5 150 μA VEN = 3.6V, VBIAS = 5.0V, IOUT = 0mA 7
Input Shutdown Current ISD 0.001 1 μA VEN = 0V, TJ = +25°C 7
Input Shutdown Current ISD 1 μA VEN = 0V, TJ = +125°C 7
Bias Supply Current IBIAS 1.5 4 mA VEN = 3.3V, VBIAS = 5.0V, IOUT = 0mA 7
Bias Shutdown Current IBIAS_SD 0.75 4 μA VEN = 0V 7
Feedback Voltage Accuracy VFB 0.594 0.6 0.606 V IOUT from 10mA to 2A, VIN from VOUT + 0.3V to 5.5V, VBIAS > 2.7V, VBIAS from VOUT + 2V to 20V, VOUT from 0.6V to 5.0V 7
Dropout Voltage VDO 36 80 mV IOUT = 2A, VOUT_NOM = 1.2V, VBIAS = 5.0V, TDFN 7
Dropout Voltage VDO 50 100 mV IOUT = 2A, VOUT_NOM = 1.2V, VBIAS = 3.3V, TDFN 7
Current Limit ILIM 2.2 2.8 3.4 A VOUTS/OUT = 0.9 x VOUT_NOM, VIN - VOUT = 300mV 7
EN Input Threshold High VIH 1 1.6 V EN rising 8
EN Input Threshold Low VIL 0.4 0.9 V EN falling 8
EN Input Leakage Current IEN_LK -1 0.001 1 μA VEN from 0V to 5.5V, VBIAS from 8V to 20V, TA = +25°C 8
POK Threshold VOUT 88 91 94 % VOUT rising (POK switches) 8
POK Voltage, Low VOL 10 100 mV IPOK = 1mA 8
POK Leakage Current IPOK_LK -1 0.001 1 μA VPOK = 5.5V, TA = +25°C 8
BYP Capacitor Range CBYP 0.001 0.1 μF Regulator remains stable; guaranteed by design 8
IN, FB, OUT, BYP, POK to GND -0.3 6 V 6
BIAS to GND -0.3 22 V 6
EN to GND -0.3 V Upper limit printed as VBIAS + 0.3V 6
Continuous Power Dissipation, TDFN 1951.2 mW TA = +70°C, derate 24.4mW/°C 6
Maximum Junction Temperature TJ 150 °C 6
Storage Temperature Range TSTG -65 150 °C 6
Lead Temperature 300 °C Soldering, 10s 6
Operating Junction Temperature Range TJ -40 125 °C 6
Thermal Resistance Junction to Ambient, Four-Layer Board θJA 41 °C/W 14 TDFN, JESD51-7 four-layer board 6
Thermal Resistance Junction to Case θJC 8 °C/W 14 TDFN 6
Thermal Resistance Junction to Ambient, Single-Layer Board θJA 54 °C/W 14 TDFN, single-layer board 6

CAD (KiCad official)

  • Symbol: MAX38909ATD+
  • Footprint: Package_DFN_QFN:DFN-14-1EP_3x3mm_P0.4mm_EP1.78x2.35mm
  • 3D model: TDFN-14(3x3) (KiCad packages3D, STEP)
  • 3D model files: max38909atd-etched.step / max38909atd-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); max38909atd.step / max38909atd.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Maxim Integrated datasheet (20 pp, sha256 cd6742c08d5c5a9b, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF