3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMD7682B50SF4
Shanghai Mingda Microelectronics · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · ESOP-8
MD7682B50SF4 from Shanghai Mingda Microelectronics, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VOUT | power_out | Regulator output pin, which needs an output ceramic capacitor of 4.7µF or greater placed close to VOUT and GND. |
| 2 | ADJ | input | Adjustable pin that sets VOUT through an external feedback resistor divider, or connected to GND for the internally set VOUT = 5V. |
| 3 | GND | power_in | Ground signal pin. |
| 4 | ILIM | passive | Current limit adjustment pin where a resistor to GND sets the limit between 300mA and 3000mA (typ.), shorting to GND gives 3000mA, and leaving it open forces the switch transistor off. |
| 5 | EN | input | Enable pin that needs a minimum of 1.6V to enable the device and a maximum of 0.4V to shut it down. |
| 6 | N.C. | unconnected | No connection pin, which may be connected to GND or left open. |
| 7 | N.C. | unconnected | No connection pin, which may be connected to GND or left open. |
| 8 | VIN | power_in | Power input pin that must be closely decoupled to GND with a ceramic capacitor of 4.7µF or greater. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Shanghai Mingda Microelectronics |
| Package | ESOP-8 |
| Category | Power Management (PMIC) |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage | VIN | 2 | 6 | V | 3 | ||
| Output Voltage Tolerance | VOUT(S) | -2 | 2 | % | IOUT=1mA | 3 | |
| Reference Voltage Tolerance | 0.686 | 0.7 | 0.714 | V | 3 | ||
| Temperature Stability | ΔVOUT/ΔTa•VOUT(s) | -40 | 40 | ppm/℃ | VIN=VEN=VOUT(S)+1.0V, IOUT=1mA, -40℃≤TA≤125℃ | 3 | |
| Enable Turn-On Threshold | 1.6 | V | Output ON | 3 | |||
| Enable Turn-Off Threshold | 0.4 | V | Output OFF | 3 | |||
| ADJ Pin Threshold | 0.05 | 0.1 | 0.2 | V | 3 | ||
| Dropout Voltage | VDROP | 380 | 500 | mV | VEN=VIN, IOUT=2A, VOUT=1.8V | 3 | |
| Dropout Voltage | VDROP | 250 | 370 | mV | VEN=VIN, IOUT=2A, VOUT=3.3V | 3 | |
| Dropout Voltage | VDROP | 240 | 360 | mV | VEN=VIN, IOUT=2A, VOUT=5V | 3 | |
| Line Regulation | 3 | 15 | mV | VOUT(S)+1V≤VIN=VEN≤6V, IOUT=1mA | 3 | ||
| Load Regulation | VOUT | 10 | 20 | mV | VIN=VEN=VOUT(S)+1.0V, 1mA≤IOUT≤2A | 3 | |
| Ground Current | IGND | 65 | μA | VEN=VIN, no load | 3 | ||
| Ground Current | IGND | 410 | μA | VEN=VIN, IOUT=100mA | 3 | ||
| Shutdown Current | ISHUT | 0.01 | μA | VEN=0 | 3 | ||
| Output Current Limit | ILIM | 3 | A | 3 | |||
| Continuous Output Current | IOUT | 2 | A | VIN>2.3V | 3 | ||
| ADJ Pin Current | 10 | nA | VADJ = VREF | 3 | |||
| Shutdown Pin Current | 0.1 | 0.5 | μA | 3 | |||
| Shutdown Exit Delay Time | 0 | μs | 3 | ||||
| Max Output Discharge Resistance to GND during Shutdown | 22 | Ω | 3 | ||||
| Reverse Current | IREV | 0.1 | 0.5 | μA | VIN=0V, VEN=2V, VOUT=5.5V | 3 | |
| VOUT Sink Current at Reverse condition | IREVS | 0.14 | 0.5 | μA | VIN=VEN=5V, VOUT=5.5V | 3 | |
| Power Supply Ripple Rejection | PSRR | 75 | dB | f=1kHz, IOUT=10mA | 3 | ||
| Power Supply Ripple Rejection | PSRR | 57 | dB | f=10kHz, IOUT=10mA | 3 | ||
| Power Supply Ripple Rejection | PSRR | 46 | dB | f=100kHz, IOUT=10mA | 3 | ||
| Power Supply Ripple Rejection | PSRR | 55 | dB | f=1MHz, IOUT=10mA | 3 | ||
| Output Noise Voltage | VOUTN | 100 | µVRMS | VOUT=3.3V, f=10Hz~100KHz | 3 | ||
| Thermal Shutdown Temperature | TSD | 160 | ℃ | IOUT=1mA | 3 | ||
| Thermal Shutdown Hysteresis | TSD_HYS | 25 | ℃ | 3 | |||
| Input Voltage | VIN | -0.3 | 7 | V | 2 | ||
| Enable Voltage | VEN | -0.3 | 7 | V | 2 | ||
| Thermal Resistance | RθJB | 80 | ℃/W | ESOP8, junction-to-board, JEDEC 4-layer (2s2p) PCB | 2 | ||
| ESD Protection HBM | ESD HBM | 4000 | V | HBM | 2 | ||
| Operating Ambient Temperature | Topr | -40 | 85 | ℃ | 2 | ||
| Storage Temperature | Tstg | -40 | 125 | ℃ | 2 |
CAD (KiCad official)
- Symbol:
MD7682B50SF4 - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm - 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files:
md7682b50sf4-etched.step/md7682b50sf4-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);md7682b50sf4.step/md7682b50sf4.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Shanghai Mingda Microelectronics datasheet (12 pp, sha256
ff741744dcd0c417, retrieved 2026-11-07, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).