Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MD7682B50SF4

Shanghai Mingda Microelectronics · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · ESOP-8

MD7682B50SF4 from Shanghai Mingda Microelectronics, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VOUT power_out Regulator output pin, which needs an output ceramic capacitor of 4.7µF or greater placed close to VOUT and GND.
2 ADJ input Adjustable pin that sets VOUT through an external feedback resistor divider, or connected to GND for the internally set VOUT = 5V.
3 GND power_in Ground signal pin.
4 ILIM passive Current limit adjustment pin where a resistor to GND sets the limit between 300mA and 3000mA (typ.), shorting to GND gives 3000mA, and leaving it open forces the switch transistor off.
5 EN input Enable pin that needs a minimum of 1.6V to enable the device and a maximum of 0.4V to shut it down.
6 N.C. unconnected No connection pin, which may be connected to GND or left open.
7 N.C. unconnected No connection pin, which may be connected to GND or left open.
8 VIN power_in Power input pin that must be closely decoupled to GND with a ceramic capacitor of 4.7µF or greater.
9 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Shanghai Mingda Microelectronics
Package ESOP-8
Category Power Management (PMIC)
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Voltage VIN 2 6 V 3
Output Voltage Tolerance VOUT(S) -2 2 % IOUT=1mA 3
Reference Voltage Tolerance 0.686 0.7 0.714 V 3
Temperature Stability ΔVOUT/ΔTa•VOUT(s) -40 40 ppm/℃ VIN=VEN=VOUT(S)+1.0V, IOUT=1mA, -40℃≤TA≤125℃ 3
Enable Turn-On Threshold 1.6 V Output ON 3
Enable Turn-Off Threshold 0.4 V Output OFF 3
ADJ Pin Threshold 0.05 0.1 0.2 V 3
Dropout Voltage VDROP 380 500 mV VEN=VIN, IOUT=2A, VOUT=1.8V 3
Dropout Voltage VDROP 250 370 mV VEN=VIN, IOUT=2A, VOUT=3.3V 3
Dropout Voltage VDROP 240 360 mV VEN=VIN, IOUT=2A, VOUT=5V 3
Line Regulation 3 15 mV VOUT(S)+1V≤VIN=VEN≤6V, IOUT=1mA 3
Load Regulation VOUT 10 20 mV VIN=VEN=VOUT(S)+1.0V, 1mA≤IOUT≤2A 3
Ground Current IGND 65 μA VEN=VIN, no load 3
Ground Current IGND 410 μA VEN=VIN, IOUT=100mA 3
Shutdown Current ISHUT 0.01 μA VEN=0 3
Output Current Limit ILIM 3 A 3
Continuous Output Current IOUT 2 A VIN>2.3V 3
ADJ Pin Current 10 nA VADJ = VREF 3
Shutdown Pin Current 0.1 0.5 μA 3
Shutdown Exit Delay Time 0 μs 3
Max Output Discharge Resistance to GND during Shutdown 22 Ω 3
Reverse Current IREV 0.1 0.5 μA VIN=0V, VEN=2V, VOUT=5.5V 3
VOUT Sink Current at Reverse condition IREVS 0.14 0.5 μA VIN=VEN=5V, VOUT=5.5V 3
Power Supply Ripple Rejection PSRR 75 dB f=1kHz, IOUT=10mA 3
Power Supply Ripple Rejection PSRR 57 dB f=10kHz, IOUT=10mA 3
Power Supply Ripple Rejection PSRR 46 dB f=100kHz, IOUT=10mA 3
Power Supply Ripple Rejection PSRR 55 dB f=1MHz, IOUT=10mA 3
Output Noise Voltage VOUTN 100 µVRMS VOUT=3.3V, f=10Hz~100KHz 3
Thermal Shutdown Temperature TSD 160 ℃ IOUT=1mA 3
Thermal Shutdown Hysteresis TSD_HYS 25 ℃ 3
Input Voltage VIN -0.3 7 V 2
Enable Voltage VEN -0.3 7 V 2
Thermal Resistance RθJB 80 ℃/W ESOP8, junction-to-board, JEDEC 4-layer (2s2p) PCB 2
ESD Protection HBM ESD HBM 4000 V HBM 2
Operating Ambient Temperature Topr -40 85 ℃ 2
Storage Temperature Tstg -40 125 ℃ 2

CAD (KiCad official)

  • Symbol: MD7682B50SF4
  • Footprint: Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm
  • 3D model: ESOP-8 (KiCad packages3D, STEP)
  • 3D model files: md7682b50sf4-etched.step / md7682b50sf4-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); md7682b50sf4.step / md7682b50sf4.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Shanghai Mingda Microelectronics datasheet (12 pp, sha256 ff741744dcd0c417, retrieved 2026-11-07, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF