Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LM27403SQX

Texas Instruments · DC-DC Controllers · WQFN-24-EP(4x4)

LM27403SQX from Texas Instruments, in a WQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SS/TRACK bidirectional Soft-start or tracking input; a capacitor to GND sets the startup rate, charged by a 3-µA current source until the reference reaches 0.6 V, or driven by an external voltage for tracking.
2 RS input Negative remote sense input that eliminates the voltage drop between GND and the load ground; connect to GND at the IC if not used.
3 FB input Feedback input to the error amplifier inverting input that sets the output voltage; FB is at 0.6 V ±1% in regulation.
4 COMP output Error amplifier output, connected to FB through a compensation network to ensure stability.
5 FADJ input Frequency adjust input; a resistor to GND programs the switching frequency between 200 kHz and 1.2 MHz.
6 SYNC input Synchronization input for PLL lock to an external clock; defaults to the FADJ-set frequency if no signal is present and should be tied to GND if not used.
7 UVLO/EN input Precision UVLO/enable input with 1.15-V rising enable threshold, 0.985-V falling threshold, 165-mV hysteresis and a 1.8-µA internal pullup that becomes 10.5 µA after enable.
8 OTP input Overtemperature protection setpoint pin; a resistor and 0.1-µF capacitor to GND set the OTP threshold, or connect to GND if system-level OTP is not required.
9 D+ input External temperature sense input for a 2N3904-type NPN transistor (base and collector shorted) used to sense inductor temperature for DCR compensation and system-level thermal shutdown.
10 D- input External temperature sense return for the thermal diode transistor, routed as a differential pair with D+ and connected to GND.
11 PGOOD output Open-drain power good output with 20-µs deglitch filter that goes low on fault or non-regulation; requires an external pullup and must not exceed 5.5 V.
12 VIN power_in Input voltage rail (3 V to 20 V) providing feedforward modulation and the internal bias supply; decouple locally to GND with a 1-µF ceramic capacitor.
13 GND power_in Common ground connection providing power and signal return for analog functions including low-side MOSFET gate return, soft-start capacitor, OTP resistor and frequency adjust resistor.
14 VDD power_out Subregulated 4.7-V internal and gate drive bias supply rail that also supplies CBOOT; decouple with a 10-µF ceramic capacitor and do not use for auxiliary loads.
15 LG output Low-side N-FET MOSFET gate drive output.
16 SW passive Power stage switch-node connection and return for the high-side N-FET gate driver.
17 HG output High-side N-FET MOSFET gate drive output.
18 CBOOT passive High-side bootstrap connection supplying the high-side gate driver; connect a 100-nF ceramic capacitor between CBOOT and SW.
19 NC unconnected No connection; connect directly to GND.
20 NC unconnected No connection; connect directly to GND.
21 NC unconnected No connection; connect directly to GND.
22 NC unconnected No connection; connect directly to GND.
23 CS+ input Current-sense positive input, the noninverting input to the current-sense comparator.
24 CS- input Current-sense negative input to the current-sense comparator; 9.9 µA of nominal offset current at room temperature adjusts the current limit setpoint.
25 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WQFN-24-EP(4x4)
Category Power Supply Chip
Pins 25

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Voltage VIN, CS+, CS-, SW -0.3 22 V 5
Voltage VDD, PGOOD -0.3 6 V 5
CBOOT voltage -0.3 24 V 5
CBOOT to SW -0.3 6 V 5
CS+ to CS- -1 1 V 5
Operating junction temperature (abs max) TJ -40 150 °C 5
Storage temperature Tstg -65 150 °C 5
ESD HBM V(ESD) -2 2 kV all pins 5
ESD CDM V(ESD) -500 500 V all pins 5
Input voltage VIN 3 20 V 5
Input voltage, VIN tied to VDD VIN 3 5.5 V VIN tied to VDD 5
VDD pin voltage VDD 2.6 4.7 5.5 V 5
SW pin voltage SW -0.3 20 V 5
Operating junction temperature TJ -40 125 °C 5
Operating free-air temperature TA -40 125 °C 5
Junction-to-ambient thermal resistance θJA 32.7 °C/W RTW 24 pins 6
Junction-to-case (top) thermal resistance θJCtop 31.2 °C/W 6
Junction-to-board thermal resistance θJB 11.2 °C/W 6
Junction-to-case (bottom) thermal resistance θJCbot 1.4 °C/W 6
Quiescent current IQ 3.5 5 mA VFB = 0.6 V (not switching) 6
Shutdown quiescent current IQ-SD 25 45 µA VUVLO/EN = 0 V 6
FB pin voltage accuracy VFB 594 600 606 mV 6
FB pin bias current IFB -165 0 165 nA VFB = 0.65 V 6
Input undervoltage lockout UVLO 2.6 2.7 2.8 V VVIN rising, VVDD rising 6
Switching frequency FSW 925 1050 1150 kHz RFADJ = 4.12 kΩ 6
Switching frequency FSW 435 500 555 kHz RFADJ = 20 kΩ 6
Switching frequency FSW 185 215 250 kHz RFADJ = 95.3 kΩ 6
Maximum duty cycle DMAX 90 93 % FSW = 500 kHz 6
Minimum off-time TOFF-MIN 110 150 190 ns VFB = 0.5 V, FSW = 500 kHz 6
VDD subregulator output voltage VDD 4.2 4.7 5.3 V IVDD = 25 mA 6
Current limit comparator offset voltage VCS_OFFSET -3.5 0 3.5 mV 6
Current limit offset current ICS 9.3 9.9 10.5 µA VCS- = 3 V, ΔVBE = 59.4 mV, TJ = 25°C 7
Current limit offset current ICS 3.4 5 6.6 µA VCS- = 3 V, D+ shorted to D- 7
ICS temperature coefficient ICS-TC 160 187 212 nA/mV Referenced to ΔVBE 7
Soft-start source current ISS 1 3 5 µA VSS/TRACK = 0 V 7
PGOOD low sink current IPGS 70 µA VPGOOD = 0.2 V, VFB = 0.75 V 7
PGOOD leakage current IPGL 1 10 µA VPGOOD = 5 V 7
Overvoltage threshold OVT 111 116.5 123 % VFB rising, RS tied to GND 7
Undervoltage threshold UVT 86 91 97 % VFB rising, RS tied to GND 7
UVLO/EN logic low threshold VUVLO1 0.94 0.985 1.03 V VUVLO/EN falling 7
UVLO/EN logic high threshold VUVLO2 1.11 1.15 1.18 V VUVLO/EN rising 7
UVLO/EN voltage hysteresis VUVLO-HYS 139 165 190 mV VUVLO/EN falling 7
UVLO/EN pullup current, disabled IUVLO1 0.8 1.8 2.7 µA VUVLO/EN = 0 V 7
UVLO/EN pullup current, enabled IUVLO2 5.5 10.5 15.5 µA VUVLO/EN = 1.25 V 7
Remote thermal current IOTP 13.5 14.6 15.5 µA ΔVBE = 79.3 mV 8
IOTP temperature coefficient IOTP-TC 158 187 213 nA/mV Referenced to ΔVBE 8
OTP resistance, thermal shutdown ROTP -5 5 % ROTP(nom) = 80.7 kΩ, ΔVBE = 79.3 mV, TJ = 125°C 8
Internal thermal shutdown threshold TSHD 150 °C Rising 8

CAD (KiCad official)

  • Symbol: LM27403SQX
  • Footprint: Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm
  • 3D model: WQFN-24-EP(4x4) (KiCad packages3D, STEP)
  • 3D model files: lm27403sqx-etched.step / lm27403sqx-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm27403sqx.step / lm27403sqx.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (56 pp, sha256 b9d9b331b0096516, retrieved 2026-10-31, tier: manufacturer)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF