3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLM27403SQX
Texas Instruments · DC-DC Controllers · WQFN-24-EP(4x4)
LM27403SQX from Texas Instruments, in a WQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SS/TRACK | bidirectional | Soft-start or tracking input; a capacitor to GND sets the startup rate, charged by a 3-µA current source until the reference reaches 0.6 V, or driven by an external voltage for tracking. |
| 2 | RS | input | Negative remote sense input that eliminates the voltage drop between GND and the load ground; connect to GND at the IC if not used. |
| 3 | FB | input | Feedback input to the error amplifier inverting input that sets the output voltage; FB is at 0.6 V ±1% in regulation. |
| 4 | COMP | output | Error amplifier output, connected to FB through a compensation network to ensure stability. |
| 5 | FADJ | input | Frequency adjust input; a resistor to GND programs the switching frequency between 200 kHz and 1.2 MHz. |
| 6 | SYNC | input | Synchronization input for PLL lock to an external clock; defaults to the FADJ-set frequency if no signal is present and should be tied to GND if not used. |
| 7 | UVLO/EN | input | Precision UVLO/enable input with 1.15-V rising enable threshold, 0.985-V falling threshold, 165-mV hysteresis and a 1.8-µA internal pullup that becomes 10.5 µA after enable. |
| 8 | OTP | input | Overtemperature protection setpoint pin; a resistor and 0.1-µF capacitor to GND set the OTP threshold, or connect to GND if system-level OTP is not required. |
| 9 | D+ | input | External temperature sense input for a 2N3904-type NPN transistor (base and collector shorted) used to sense inductor temperature for DCR compensation and system-level thermal shutdown. |
| 10 | D- | input | External temperature sense return for the thermal diode transistor, routed as a differential pair with D+ and connected to GND. |
| 11 | PGOOD | output | Open-drain power good output with 20-µs deglitch filter that goes low on fault or non-regulation; requires an external pullup and must not exceed 5.5 V. |
| 12 | VIN | power_in | Input voltage rail (3 V to 20 V) providing feedforward modulation and the internal bias supply; decouple locally to GND with a 1-µF ceramic capacitor. |
| 13 | GND | power_in | Common ground connection providing power and signal return for analog functions including low-side MOSFET gate return, soft-start capacitor, OTP resistor and frequency adjust resistor. |
| 14 | VDD | power_out | Subregulated 4.7-V internal and gate drive bias supply rail that also supplies CBOOT; decouple with a 10-µF ceramic capacitor and do not use for auxiliary loads. |
| 15 | LG | output | Low-side N-FET MOSFET gate drive output. |
| 16 | SW | passive | Power stage switch-node connection and return for the high-side N-FET gate driver. |
| 17 | HG | output | High-side N-FET MOSFET gate drive output. |
| 18 | CBOOT | passive | High-side bootstrap connection supplying the high-side gate driver; connect a 100-nF ceramic capacitor between CBOOT and SW. |
| 19 | NC | unconnected | No connection; connect directly to GND. |
| 20 | NC | unconnected | No connection; connect directly to GND. |
| 21 | NC | unconnected | No connection; connect directly to GND. |
| 22 | NC | unconnected | No connection; connect directly to GND. |
| 23 | CS+ | input | Current-sense positive input, the noninverting input to the current-sense comparator. |
| 24 | CS- | input | Current-sense negative input to the current-sense comparator; 9.9 µA of nominal offset current at room temperature adjusts the current limit setpoint. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-24-EP(4x4) |
| Category | Power Supply Chip |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage VIN, CS+, CS-, SW | -0.3 | 22 | V | 5 | |||
| Voltage VDD, PGOOD | -0.3 | 6 | V | 5 | |||
| CBOOT voltage | -0.3 | 24 | V | 5 | |||
| CBOOT to SW | -0.3 | 6 | V | 5 | |||
| CS+ to CS- | -1 | 1 | V | 5 | |||
| Operating junction temperature (abs max) | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| ESD HBM | V(ESD) | -2 | 2 | kV | all pins | 5 | |
| ESD CDM | V(ESD) | -500 | 500 | V | all pins | 5 | |
| Input voltage | VIN | 3 | 20 | V | 5 | ||
| Input voltage, VIN tied to VDD | VIN | 3 | 5.5 | V | VIN tied to VDD | 5 | |
| VDD pin voltage | VDD | 2.6 | 4.7 | 5.5 | V | 5 | |
| SW pin voltage | SW | -0.3 | 20 | V | 5 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 5 | ||
| Operating free-air temperature | TA | -40 | 125 | °C | 5 | ||
| Junction-to-ambient thermal resistance | θJA | 32.7 | °C/W | RTW 24 pins | 6 | ||
| Junction-to-case (top) thermal resistance | θJCtop | 31.2 | °C/W | 6 | |||
| Junction-to-board thermal resistance | θJB | 11.2 | °C/W | 6 | |||
| Junction-to-case (bottom) thermal resistance | θJCbot | 1.4 | °C/W | 6 | |||
| Quiescent current | IQ | 3.5 | 5 | mA | VFB = 0.6 V (not switching) | 6 | |
| Shutdown quiescent current | IQ-SD | 25 | 45 | µA | VUVLO/EN = 0 V | 6 | |
| FB pin voltage accuracy | VFB | 594 | 600 | 606 | mV | 6 | |
| FB pin bias current | IFB | -165 | 0 | 165 | nA | VFB = 0.65 V | 6 |
| Input undervoltage lockout | UVLO | 2.6 | 2.7 | 2.8 | V | VVIN rising, VVDD rising | 6 |
| Switching frequency | FSW | 925 | 1050 | 1150 | kHz | RFADJ = 4.12 kΩ | 6 |
| Switching frequency | FSW | 435 | 500 | 555 | kHz | RFADJ = 20 kΩ | 6 |
| Switching frequency | FSW | 185 | 215 | 250 | kHz | RFADJ = 95.3 kΩ | 6 |
| Maximum duty cycle | DMAX | 90 | 93 | % | FSW = 500 kHz | 6 | |
| Minimum off-time | TOFF-MIN | 110 | 150 | 190 | ns | VFB = 0.5 V, FSW = 500 kHz | 6 |
| VDD subregulator output voltage | VDD | 4.2 | 4.7 | 5.3 | V | IVDD = 25 mA | 6 |
| Current limit comparator offset voltage | VCS_OFFSET | -3.5 | 0 | 3.5 | mV | 6 | |
| Current limit offset current | ICS | 9.3 | 9.9 | 10.5 | µA | VCS- = 3 V, ΔVBE = 59.4 mV, TJ = 25°C | 7 |
| Current limit offset current | ICS | 3.4 | 5 | 6.6 | µA | VCS- = 3 V, D+ shorted to D- | 7 |
| ICS temperature coefficient | ICS-TC | 160 | 187 | 212 | nA/mV | Referenced to ΔVBE | 7 |
| Soft-start source current | ISS | 1 | 3 | 5 | µA | VSS/TRACK = 0 V | 7 |
| PGOOD low sink current | IPGS | 70 | µA | VPGOOD = 0.2 V, VFB = 0.75 V | 7 | ||
| PGOOD leakage current | IPGL | 1 | 10 | µA | VPGOOD = 5 V | 7 | |
| Overvoltage threshold | OVT | 111 | 116.5 | 123 | % | VFB rising, RS tied to GND | 7 |
| Undervoltage threshold | UVT | 86 | 91 | 97 | % | VFB rising, RS tied to GND | 7 |
| UVLO/EN logic low threshold | VUVLO1 | 0.94 | 0.985 | 1.03 | V | VUVLO/EN falling | 7 |
| UVLO/EN logic high threshold | VUVLO2 | 1.11 | 1.15 | 1.18 | V | VUVLO/EN rising | 7 |
| UVLO/EN voltage hysteresis | VUVLO-HYS | 139 | 165 | 190 | mV | VUVLO/EN falling | 7 |
| UVLO/EN pullup current, disabled | IUVLO1 | 0.8 | 1.8 | 2.7 | µA | VUVLO/EN = 0 V | 7 |
| UVLO/EN pullup current, enabled | IUVLO2 | 5.5 | 10.5 | 15.5 | µA | VUVLO/EN = 1.25 V | 7 |
| Remote thermal current | IOTP | 13.5 | 14.6 | 15.5 | µA | ΔVBE = 79.3 mV | 8 |
| IOTP temperature coefficient | IOTP-TC | 158 | 187 | 213 | nA/mV | Referenced to ΔVBE | 8 |
| OTP resistance, thermal shutdown | ROTP | -5 | 5 | % | ROTP(nom) = 80.7 kΩ, ΔVBE = 79.3 mV, TJ = 125°C | 8 | |
| Internal thermal shutdown threshold | TSHD | 150 | °C | Rising | 8 |
CAD (KiCad official)
- Symbol:
LM27403SQX - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: WQFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
lm27403sqx-etched.step/lm27403sqx-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm27403sqx.step/lm27403sqx.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (56 pp, sha256
b9d9b331b0096516, retrieved 2026-10-31, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).