Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

STM32G071CBU6

STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · UFQFPN-48(7x7)

STM32G071CBU6 from STMicroelectronics, in a UFQFPN-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 PC13 bidirectional I/O port PC13 is a 5 V-tolerant FT pin supplied through the power switch, limited to about 3 mA sink and to 2 MHz output at 30 pF.
2 PC14-OSC32_IN bidirectional PC14 is a 5 V-tolerant FT GPIO that doubles as the 32.768 kHz oscillator input OSC32_IN, and it is supplied through the power switch.
3 PC15-OSC32_OUT bidirectional PC15 is a 5 V-tolerant FT GPIO that doubles as the 32.768 kHz oscillator output OSC32_OUT, and it is supplied through the power switch.
4 VBAT power_in VBAT is the backup supply for the RTC, TAMP, LSE and backup registers, specified at 1.55 V to 3.6 V when VDD is absent.
5 VREF+ power_in VREF+ is the analog reference input, which must equal VDDA when VDDA is below 2 V, and it can be grounded when analog peripherals are inactive.
6 VDD/VDDA power_in VDD/VDDA is the 1.7 V to 3.6 V digital supply that also feeds the analog supply VDDA (ADC/COMP 1.62 V min, DAC 1.8 V min, VREFBUF 2.4 V min).
7 VSS/VSSA power_in VSS/VSSA is the common ground for the digital and analog supply domains.
8 PF0-OSC_IN bidirectional PF0 is an FT GPIO that doubles as the HSE crystal oscillator input OSC_IN, and it also carries TIM14_CH1.
9 PF1-OSC_OUT bidirectional PF1 is an FT GPIO that doubles as the HSE crystal oscillator output OSC_OUT, and it also carries TIM15_CH1N and OSC_EN.
10 PF2-NRST bidirectional PF2 is an FT I/O that is also the bidirectional NRST reset pin with an embedded weak pull-up resistor, and it can output MCO.
11 PA0 bidirectional PA0 is a FT_a I/O with analog switch function that also provides ADC_IN0, WKUP1 and COMP1_OUT alternate outputs.
12 PA1 bidirectional PA1 is a FT_a I/O with analog switch function that also provides ADC_IN1, COMP1_INP and SPI1_SCK/I2S1_CK alternate functions.
13 PA2 bidirectional PA2 is a FT_a I/O with analog switch function that also provides ADC_IN2, COMP2_INM, WKUP4 and USART2_TX alternate functions.
14 PA3 bidirectional PA3 is a FT_a I/O with analog switch function that also provides ADC_IN3, COMP2_INP and USART2_RX alternate functions.
15 PA4 bidirectional PA4 is a TT_a I/O (3.6 V tolerant) with analog switch function that also provides ADC_IN4, DAC_OUT1 and RTC_OUT2.
16 PA5 bidirectional PA5 is a TT_a I/O (3.6 V tolerant) with analog switch function that also provides ADC_IN5 and DAC_OUT2 alternate outputs.
17 PA6 bidirectional PA6 is a FT_a I/O with analog switch function that also provides ADC_IN6 and COMP1_OUT alternate outputs.
18 PA7 bidirectional PA7 is a FT_a I/O with analog switch function that also provides ADC_IN7 and COMP2_OUT alternate outputs.
19 PB0 bidirectional PB0 is a FT_a I/O with analog switch function that also provides ADC_IN8 and COMP1_OUT alternate outputs.
20 PB1 bidirectional PB1 is a FT_a I/O with analog switch function that also provides ADC_IN9, COMP1_INM and LPUART1_RTS_DE alternate functions.
21 PB2 bidirectional PB2 is a FT_a I/O with analog switch function that also provides ADC_IN10, COMP1_INP and SPI2_MISO alternate functions.
22 PB10 bidirectional PB10 is a FT_fa I/O (Fm+ capable, with analog switch) that also provides ADC_IN11, I2C2_SCL and COMP1_OUT alternate functions.
23 PB11 bidirectional PB11 is a FT_fa I/O (Fm+ capable, with analog switch) that also provides ADC_IN15, I2C2_SDA and COMP2_OUT alternate functions.
24 PB12 bidirectional PB12 is a FT_a I/O with analog switch function that also provides ADC_IN16, SPI2_NSS and TIM1_BKIN alternate functions.
25 PB13 bidirectional PB13 is a FT_f I/O (Fm+ capable) that also provides SPI2_SCK, I2C2_SCL and TIM1_CH1N alternate functions.
26 PB14 bidirectional PB14 is a FT_f I/O (Fm+ capable) that also provides SPI2_MISO, I2C2_SDA and UCPD1_FRSTX alternate functions.
27 PB15 bidirectional PB15 is a FT_c I/O (USB Type-C PD capable) that also provides SPI2_MOSI, TIM1_CH3N and UCPD1_CC2 alternate functions.
28 PA8 bidirectional PA8 is a FT_c I/O (USB Type-C PD capable) that also provides MCO, SPI2_NSS, TIM1_CH1 and UCPD1_CC1 alternate functions.
29 PA9 bidirectional PA9 is a FT_fd I/O (Fm+ capable, USB Type-C dead battery) that also provides MCO, USART1_TX, TIM1_CH2 and I2C1_SCL alternate functions.
30 PC6 bidirectional PC6 is an FT I/O that also provides UCPD1_FRSTX, TIM3_CH1 and TIM2_CH3 alternate functions.
31 PC7 bidirectional PC7 is an FT I/O that also provides UCPD2_FRSTX, TIM3_CH2 and TIM2_CH4 alternate functions.
32 PA10 bidirectional PA10 is a FT_fd I/O (Fm+ capable, USB Type-C dead battery) that also provides SPI2_MOSI, USART1_RX, TIM1_CH3 and I2C1_SDA alternate functions.
33 PA11 [PA9] bidirectional PA11 is a FT_f I/O (Fm+ capable) that also provides SPI1_MISO/I2S1_MCK, USART1_CTS, TIM1_CH4 and I2C2_SCL, and it can be remapped with PA9 through SYSCFG_CFGR1.
34 PA12 [PA10] bidirectional PA12 is a FT_f I/O (Fm+ capable) that also provides SPI1_MOSI/I2S1_SD, USART1_RTS_DE_CK, TIM1_ETR and I2C2_SDA, and it can be remapped with PA10 through SYSCFG_CFGR1.
35 PA13 bidirectional PA13 is a FT I/O that carries the SWDIO serial-wire debug data line and has an internal pull-up enabled after reset.
36 PA14-BOOT0 bidirectional PA14 is a FT I/O that carries the SWCLK debug clock and doubles as the BOOT0 boot-mode pin, with an internal pull-down enabled after reset.
37 PA15 bidirectional PA15 is a FT I/O that provides SPI1_NSS/I2S1_WS, USART2_RX, TIM2_CH1_ETR and USART3_RTS_DE_CK alternate functions.
38 PD0 bidirectional PD0 is a FT_c I/O (USB Type-C PD capable) that also provides EVENTOUT, SPI2_NSS, TIM16_CH1 and UCPD2_CC1 alternate functions.
39 PD1 bidirectional PD1 is a FT_d I/O (USB Type-C PD dead battery) that also provides EVENTOUT, SPI2_SCK, TIM17_CH1 and UCPD2_DBCC1 alternate functions.
40 PD2 bidirectional PD2 is a FT_c I/O (USB Type-C PD capable) that also provides USART3_RTS_DE_CK, TIM3_ETR, TIM1_CH1N and UCPD2_CC2 alternate functions.
41 PD3 bidirectional PD3 is a FT_d I/O (USB Type-C PD dead battery) that also provides USART2_CTS, SPI2_MISO, TIM1_CH2N and UCPD2_DBCC2 alternate functions.
42 PB3 bidirectional PB3 is a FT_a I/O with analog switch function that also provides SPI1_SCK/I2S1_CK, TIM1_CH2, TIM2_CH2 and COMP2_INM.
43 PB4 bidirectional PB4 is a FT_a I/O with analog switch function that also provides SPI1_MISO/I2S1_MCK, TIM3_CH1, USART1_CTS and COMP2_INP.
44 PB5 bidirectional PB5 is an FT I/O that also provides SPI1_MOSI/I2S1_SD, TIM3_CH2, I2C1_SMBA, LPTIM1_IN1, COMP2_OUT and the WKUP6 wakeup function.
45 PB6 bidirectional PB6 is a FT_fa I/O (Fm+ capable, with analog switch) that also provides USART1_TX, TIM1_CH3, I2C1_SCL and COMP2_INP alternate functions.
46 PB7 bidirectional PB7 is a FT_fa I/O (Fm+ capable, with analog switch) that also provides USART1_RX, SPI2_MOSI, I2C1_SDA, COMP2_INM and PVD_IN.
47 PB8 bidirectional PB8 is a FT_f I/O (Fm+ capable) that also provides CEC, SPI2_SCK, TIM16_CH1, USART3_TX and I2C1_SCL alternate functions.
48 PB9 bidirectional PB9 is a FT_f I/O (Fm+ capable) that also provides IR_OUT, UCPD2_FRSTX, TIM17_CH1, USART3_RX, SPI2_NSS and I2C1_SDA alternate functions.
49 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package UFQFPN-48(7x7)
Category Embedded Processors & Controllers
Pins 49

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Standard operating voltage VDD 1.7 3.6 V 55
Analog supply voltage for ADC and COMP operation VDDA 1.62 3.6 V For ADC and COMP operation 55
Analog supply voltage for DAC operation VDDA 1.8 3.6 V For DAC operation 55
Analog supply voltage for VREFBUF operation VDDA 2.4 3.6 V For VREFBUF operation 55
Backup operating voltage VBAT 1.55 3.6 V 55
Internal AHB clock frequency fHCLK 0 64 MHz 55
Internal APB clock frequency fPCLK 0 64 MHz 55
Ambient temperature (suffix 6) TA -40 85 °C Suffix 6 55
Junction temperature (suffix 6) TJ -40 105 °C Suffix 6 55
External supply voltage VDD -0.3 4 V 54
External supply voltage on VBAT pin VBAT -0.3 4 V 54
Current into VDD/VDDA power pin (source) IVDD/VDDA 100 mA 54
Current out of VSS/VSSA ground pin (sink) IVSS/VSSA 100 mA 54
Output current sunk by any I/O and control pin IIO(PIN) 15 mA Except FT_f pins 54
Output current sunk by any FT_f pin IIO(PIN) 20 mA FT_f pin 54
Output current sourced by any I/O and control pin IIO(PIN) 15 mA 54
Total output current sunk by sum of all I/Os and control pins ∑IIO(PIN) 80 mA 54
Total output current sourced by sum of all I/Os and control pins ∑IIO(PIN) 80 mA 54
Storage temperature range TSTG -65 150 °C 55
Maximum junction temperature TJ 150 °C 55
Internal reference voltage VREFINT 1.182 1.212 1.232 V -40°C < TJ < 130°C 57
Power-on reset threshold VPOR 1.62 1.66 1.7 V 56
Power-down reset threshold VPDR 1.6 1.64 1.69 V 56
Brownout reset threshold 1, VDD rising VBOR1 2.05 2.1 2.18 V VDD rising 56
Brownout reset threshold 2, VDD rising VBOR2 2.2 2.31 2.38 V VDD rising 56
Brownout reset threshold 3, VDD rising VBOR3 2.5 2.62 2.68 V VDD rising 56
Brownout reset threshold 4, VDD rising VBOR4 2.8 2.91 3 V VDD rising 56
POR temporization when VDD crosses VPOR tRSTTEMPO 250 400 μs VDD rising 56
HSI16 frequency fHSI16 15.88 16.08 MHz VDD=3.0 V, TA=30 °C 72
LSI frequency fLSI 31.04 32.96 kHz VDD = 3.0 V, TA = 30 °C 73
LSI frequency over supply and temperature fLSI 29.5 34 kHz VDD = 1.62 V to 3.6 V, TA = -40 to 125 °C 73
HSE oscillator frequency fOSC_IN 4 8 48 MHz 69
HSE feedback resistor RF 200 kΩ 69
PLL input clock frequency fPLL_IN 2.66 16 MHz 74
ADC clock frequency, Range 1 fADC 0.14 35 MHz Range 1 85
ADC clock frequency, Range 2 fADC 0.14 16 MHz Range 2 85
External input impedance RAIN 50 kΩ 85
Weak pull-up equivalent resistor RPU 25 40 55 kΩ VIN = VSS 79
Weak pull-down equivalent resistor RPD 25 40 55 kΩ VIN = VDDIO1 79
Supply current in Standby mode, RTC disabled IDD(Standby) 0.2 0.9 µA VDD = 3.0 V, 25 °C 62
Flash endurance NEND 10 kcycles TA = -40 to +105 °C 75
I/O pin capacitance CIO 5 pF 79
ADC internal sample and hold capacitor CADC 5 pF 85

CAD (KiCad official)

  • Symbol: STM32G071CBU6
  • Footprint: Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm
  • 3D model: UFQFPN-48(7x7) (KiCad packages3D, STEP)
  • 3D model files: stm32g071cbu6-etched.step / stm32g071cbu6-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm32g071cbu6.step / stm32g071cbu6.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (133 pp, sha256 96d7e9ca1500e794, retrieved 2026-11-05, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF