Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT8608EDC#TRMPBF

Analog Devices · DC-DC Converters · DFN-8-EP(2x2)

LT8608EDC#TRMPBF from Analog Devices, in a DFN-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 BST passive Provides drive voltage higher than VIN to the topside power switch; place a 0.1µF boost capacitor as close as possible to the IC with no series resistor.
2 SW output Output of the internal power switches; connect to the inductor and boost capacitor and keep the node small on the PCB.
3 INTVCC power_out Internal 3.5V regulator bypass pin (varies 2.8V to 3.5V, 20mA max output); decouple with at least 1µF low-ESR ceramic and do not load with external circuitry.
4 RT passive A resistor from RT to ground sets the switching frequency (200kHz to 2.2MHz range).
5 FB input Feedback input regulated to 0.778V; connect the feedback resistor divider tap here.
6 PG output Open-drain power-good output that stays low until FB is within ±8.5% of final regulation and no faults exist; valid when VIN is above 3.2V.
7 VIN power_in Supplies the internal circuitry and topside power switch (3.0V to 42V operating range, 42V abs max); must be locally bypassed close to VIN and GND.
8 EN/UV input Shuts down the part when low and enables when high, with 1.05V rising and 1.00V falling thresholds; tie to VIN if unused or use a divider from VIN to set UVLO.
9 GND power_in Exposed pad ground; connect to the negative terminal of the input capacitor and solder to the PCB to lower thermal resistance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package DFN-8-EP(2x2)
Category Power Supply Chip
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Minimum Input Voltage VIN(MIN) 2.5 3 V over full operating temperature range 2
VIN Quiescent Current (shutdown) IQ 1 4 µA VEN/UV = 0V, VSYNC = 0V 2
VIN Quiescent Current (not switching) IQ 1.7 12 µA VEN/UV = 2V, Not Switching, VSYNC = 0V or LT8608 DFN, VIN ≤ 36V 2
VIN Current in Regulation (100µA load) 56 90 µA VIN = 6V, VOUT = 2.7V, Output Load = 100µA 2
VIN Current in Regulation (1mA load) 500 700 µA VIN = 6V, VOUT = 2.7V, Output Load = 1mA 2
Feedback Reference Voltage DFN VFB 0.773 0.778 0.783 V DFN Package, VIN = 6V, ILOAD = 100mA 3
Feedback Reference Voltage DFN (full temp) VFB 0.753 0.778 0.803 V DFN Package, VIN = 6V, ILOAD = 100mA, over full temperature range 3
Feedback Voltage Line Regulation 0.02 0.06 %/V VIN = 4.0V to 40V 3
Feedback Pin Input Current -20 20 nA VFB = 1V 3
Minimum On-Time tON(MIN) 35 65 ns ILOAD = 1A, SYNC = 0V or LT8608 DFN 3
Minimum Off Time tOFF(MIN) 93 130 ns 3
Oscillator Frequency DFN (RT=221k) fSW 130 200 270 kHz RT = 221k, ILOAD = 500mA 3
Oscillator Frequency DFN (RT=60.4k) fSW 610 700 790 kHz RT = 60.4k, ILOAD = 500mA 3
Oscillator Frequency DFN (RT=18.2k) fSW 1.85 2 2.15 MHz RT = 18.2k, ILOAD = 200mA 3
Top Power NMOS On-Resistance RDS(ON) 350 mΩ ILOAD = 0.5A 3
Top Power NMOS Current Limit ILIM 2.1 2.9 3.9 A 3
Bottom Power NMOS On-Resistance RDS(ON) 230 mΩ 3
SW Leakage Current 15 µA VIN = 36V 3
EN/UV Pin Threshold 0.99 1.05 1.11 V EN/UV Rising 3
EN/UV Pin Hysteresis 50 mV 3
EN/UV Pin Current -20 20 nA VEN/UV = 2V 3
PG Upper Threshold Offset from VFB 5 8.5 13 % VFB Rising 3
PG Lower Threshold Offset from VFB 5 8.5 13 % VFB Falling 3
PG Hysteresis 0.5 % 3
PG Leakage -200 200 nA VPG = 42V 3
PG Pull-Down Resistance 550 1200 Ω VPG = 0.1V 3
VIN, EN/UV, PG Voltage 42 V 2
FB Voltage 4 V FB, TR/SS 2
Operating Junction Temperature Range LT8608E TJ -40 125 °C LT8608E 2
Storage Temperature Range TSTG -65 150 °C 2

CAD (KiCad official)

  • Symbol: LT8608EDC#TRMPBF
  • Footprint: Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.45mm_EP0.64x1.37mm
  • 3D model: DFN-8-EP(2x2) (KiCad packages3D, STEP)
  • 3D model files: lt8608edc-trmpbf-etched.step / lt8608edc-trmpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8608edc-trmpbf.step / lt8608edc-trmpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (24 pp, sha256 ef5ca800fd4c6a67, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF